Mec Speed Level Series Service & Parts Manual page 105

Secton 8 - Troubleshootng - 3084RT Models
Operation ID
5F-1
5F-2
5F-3
5F
5F-4
OUTRIGGERS
5F-5
Called "Outriggers"
5F-6
on the EZ-Cal,
5F-7
these personalities
effect Auto-level
5F-8
function
5F-9
5F-10
5F-11
5G-1
5G
5G-2
GROUND MODE
5G-3
5G-4
Lower Control
5G-5
Operations
5G-6
5H-1
5H-2
5H
TILT
5H-3
5H-4
TILT 2 5H-4
5H-5A
Sub Menu 5H-5B
5H-5C
5I-1
5I
OVERLOAD
5I-2
5I-3
ANSI: values = 0
5I-4
CE: values apply 5I-5
5I-6
5I-7
OVERLOAD 2 5I-8
5I-8a
Sub Menu
5I-8b
5J-1
5J
5J-2
ALARMS
5J-3
5K-1
5K-2
5K-3
5K-4
5K
HEIGHTS
5K-5
5K-6
5K-7
5K-8
Page 98
Personality Factory Setting
Outriggers
Extend
Level
Retract
Debounce
Initial
Tilt filter
X Tilt target 0.2 deg
Y Tilt target 0.2 deg
Tilt Slack 0.3 deg
Outrigger Test Yes/No
UP
DOWN
OUT
IN
ACCEL 1.0 sec
DECEL 1.0 sec
X Trip 2.0 degrees
Y Trip 2.0 degrees
Delay Trip 2.0 sec
Delay Clear 0.5 sec
Tilt 2
At Height
X Trip 2 1.5 sec
Y Trip 2 1.5 sec
Trip @ ANSI: 0%
Lamp @ ANSI: 0%
Alarm @ ANSI: 0%
@ Height ANSI: 0%
Safe Down ANSI: 0%
Delay Trip 1.5 sec
Delay Clear 1.5 sec
Overload # 2
@ Height
Scale
Drive: Yes/No
Lift 2 = Down
Tilt 1 = When Elevated
Elevation
Maximum Drive
Maximum Lift ANSI: 101%
Armguard
Overload ANSI: 0%
Safe Down ANSI: 0%
Overload # 2
Tilt # 2 ANSI: 0%
Speed Level Seres - Servce & Parts Manual
2 Not Used
50% O/R speed before all legs down
35% O/R speed after all legs touch down
55% Maximum speed potential
0.35 Compensates for switch bounce
0.5 Not Used
6 Compensates for tilt sensor free movement
Target level stops movement
Target level stops movement
Additional compensation
Not Used
53% Maximum speed potential
0% Gravity down
0% Power deck operation (not used)
0% Power deck operation (not used)
Ramp-up time to maximum
Ramp-down drive output
Angle tilt sensor signals Out Of Level
Angle tilt sensor signals Out Of Level
Time delay between Tip and Signal
Time delay between Tip and Signal OFF
- Sub category, press ENTER to access
101% Point where lesser tilt angle used
Not Used
Not Used
CE: 110% % of weight over maximum to trigger overload
CE: 0% % of weight over maximum to trigger lamp
CE: 0% % of weight over maximum to trigger alarm
CE: 8% % of elevation load sense starts monitoring weight
CE: 12% % of elevation lift-down still operates in overload
Delay before overload trip
Delay before overload clear
- Sub category, press ENTER to access
0% % of height for secondary overload valve
100% % of reduced overload valve
No 1 = FWD
1 = UP
1 = When Elevated
15% Point at which machine enters elevated mode
101% Maximum drivable height
CE: 98% Maximum elevated height potential
101% Stops descent for 5 sec
CE: 8% % of elevation load sense starts monitoring weight
CE: 12% % of elevation lift-down still operates in overload
0% Not Used
CE: 0% Reduced degree of tilt at % elevation
January 2019
Explanation
2 = REV 3 = Both 4 = All Motion
2 = DOWN 3 = Both 4 = All Motion
2 = Always