Toshiba e-STUDIO477S Service Manual page 406

e-STUDIO477S/527S
05/08 Mode Element Sub Element
08 Setting System User interface
mode
08 Setting System Finisher
mode
08 Setting System Finisher
mode
08 Setting System Finisher
mode
08 Setting System Finisher
mode
08 Setting System Finisher
mode
08 Setting System Finisher
mode
08 Setting System Scanning
mode
08 Setting System Maintenance
mode
08 Setting System User interface
mode
08 Setting System
mode
08 Setting System HDD
mode
08 Setting System HDD
mode
08 Setting Mode
Item Subitem Code
Counter installed 9037
externally
Finisher tray 9048
operating mode
Finisher tray 9048
operating mode
Finisher tray 9048
operating mode
Finisher tray 9048
operating mode
Finisher tray 9048
operating mode
Finisher tray 9048
operating mode
9049
General 9050
Display setting 9051
9060
9065
9072
Sub- Default
Details
Code value
Job handling-short paid- 1
coin controller
0 Operating mode 1 0
1 Operating mode 2 0
2 Operating mode 3 0
3 Operating mode 4 0
4 Operating mode 5 0
5 Operating mode 6 0
Scanning operating mode 0
Performing panel calibration
Panel calibration setting 0
value
Destination display at Refer to
SRAM initialization contents
HDD diagnostic menu
display
Performing HDD testing
53
Acceptable
RAM Contents
value
0~2 SYS Sets whether pause or stop the printing job when it
is short paid using a coin controller.
0: Pause the job
1: Stop the job
2: Stop the job immediately
It is recommended to select "2" (Stop the job
immediately) when you want to set "stop" while the
multiple numbers of USB direct printing is
performed. (To shorten of hours)
0~1 SYS For plain paper, thick 1, LG. For non-sort mode
and sort mode. Do not change this setting unless
otherwise instructed.
0: Disabled 1: Enabled
0~1 SYS For thick 2. Do not change this setting unless
otherwise instructed.
0: Disabled 1: Enabled
0~1 SYS For thick 3. Do not change this setting unless
otherwise instructed.
0: Disabled 1: Enabled
0~1 SYS For thick 4. Do not change this setting unless
otherwise instructed.
0: Disabled 1: Enabled
0~1 SYS For LG. For Single-sided stapling. Do not change
this setting unless otherwise instructed.
0: Disabled 1: Enabled
0~1 SYS For single-sided stapling. Do not change this
setting unless otherwise instructed.
0: Disabled 1: Enabled
0~1 SYS Do not change this setting unless otherwise
instructed.
0: Operating mode 1
1: Operating mode 2
SYS Performs the calibration of the pressing position on
the touch panel (LCD screen).
The calibration is performed by pressing 4
reference positions after this code is started up.
0~1 SYS Switches whether the screen for displaying panel
calibration setting values is displayed or not.
0: Disabled (screen not displayed)
1: Enabled (screen displayed)
0~255 SYS 0: MJD 1: NAD 2: JPD 3: AUD 4: Not defined 5:
Not defined 6: Not defined 7: Not defined 8: Not
defined 9: Not defined 10: ARD 11: Not defined
<Default value>
JPD: 2 NAD: 1 MJD: 0 AUD: 3 ARD: 10
SYS Displays the HDD information.
SYS Checks the bad sector. It may take more than 30
minutes to finish the checking.
Proc
ServiceUI
edure
1
4
4
4
4
4
4
1
1 Yes
1 Yes
2
2 Yes
3
Ver03