HP StoreAll Series Installation Manual page 120

9. If the server is an HP StoreAll 9300, 9320, 8200 or 8800 Storage system, configure iLO
settings:
a. Enter the following command:
ibrix_ilo
<ILOIPADDRESS> is the iLO IP address of the server that has been registered. It is the
address listed in the iLO IP Address column of the File Servers screen. See
117). In
10.103.10.106.
<ILOSUBNETMASK> in the above command is the subnetmask for the server iLO port.
NOTE:
b. Enter the following command:
ibrix_ilo
The following example shows the commands and the output:
[root@r3r10-s6 ibrix]# ibrix_ilo -v -a -i 10.103.10.106 -m 255.255.255.0
CMD:
/sbin/hponcfg -f /tmp/ibrix_ilo-24811.xml
XML:
<RIBCL VERSION="2.0">
<LOGIN USER_LOGIN="Administrator" PASSWORD="">
<RIB_INFO MODE="write">
</RIB_INFO>
</LOGIN>
</RIBCL>
HP Lights-Out Online Configuration utility
Version 4.2.0 Date 6/10/2013 (c) Hewlett-Packard Company, 2013
Firmware Revision = 1.30 Device type = iLO 4 Driver name = hpilo
<INFORM> DHCP is currently disabled, enable DHCP to use any DHCP setting.</INFORM>
<INFORM>Integrated Lights-Out will reset at the end of the script.</INFORM>
Please wait while the firmware is reset. This might take a minute
Script succeeded
[root@r3r10-s6 ibrix]# ibrix_ilo -u ibrixpwr -p hpinvent
HP Lights-Out Online Configuration utility
Version 4.2.0 Date 6/10/2013 (c) Hewlett-Packard Company, 2013
Firmware Revision = 1.30 Device type = iLO 4 Driver name = hpilo
Script succeeded
10. Log in to the server that is running the active version of Fusion Manager ( the same server
running the Getting Started wizard), and enter:
/usr/local/ibrix/autocfg/bin/StoreAll_hosts_setup
The following example shows the commands and the output:
120 Configuring clusters remotely with the Getting Started Wizard
v a i <ILOIPADDRESS> -m <ILOSUBNETMASK>
Figure 44 (page 117), the value of <ILOIPADDRESS> for server r3r10-s6 is
Use the iLO utility tools to determine the subnetmask.
u ibrixpwr
<MOD_NETWORK_SETTINGS>
<ENABLE_NIC value="Yes"/>
<SPEED_AUTOSELECT value="Yes"/>
<FULL_DUPLEX value="Yes"/>
<DHCP_ENABLE value="No"/>
<IP_ADDRESS value="10.103.10.106"/>
<SUBNET_MASK value="255.255.255.0"/>
<DNS_NAME value=""/>
<DHCP_DOMAIN_NAME value="No"/>
<DHCP_GATEWAY value="No"/>
<DHCP_DNS_SERVER value="No"/>
<DHCP_WINS_SERVER value="No"/>
<DHCP_STATIC_ROUTE value="No"/>
<REG_WINS_SERVER value="No"/>
<REG_DDNS_SERVER value="No"/>
<PING_GATEWAY value="No"/>
<PRIM_DNS_SERVER value="0.0.0.0"/>
<SEC_DNS_SERVER value="0.0.0.0"/>
<TER_DNS_SERVER value="0.0.0.0"/>
<PRIM_WINS_SERVER value="0.0.0.0"/>
<SEC_WINS_SERVER value="0.0.0.0"/>
<STATIC_ROUTE_1 DEST="0.0.0.0" GATEWAY="0.0.0.0"/>
<STATIC_ROUTE_2 DEST="0.0.0.0" GATEWAY="0.0.0.0"/>
<STATIC_ROUTE_3 DEST="0.0.0.0" GATEWAY="0.0.0.0"/>
</MOD_NETWORK_SETTINGS>
p hpinvent
Figure 44 (page