Stereo-Linking Aux Channels - RSS M-380 Owner's Manual

AUX channel and MAIN L/R channel operations
a. Fader
This adjusts the output level in the range of -Inf dB–+10.0 dB.
b. S button
This turns SOLO on/off for the channel.
c. M button
This turns MUTE on/off for the channel.
d. Channel meter
This indicates the signal level of the channel. For stereo-linked
channels, two meters (L and R) are shown. The point at which
the signal level is detected will be as specified in the METER
screen. For details, refer to "Editing the meter settings" (p. 96).
The function buttons have the following operations.
[F1 (LINK)]* Turns channel link on/off.
[F2 (NAME EDIT)] Accesses the NAME EDIT
popup where you can specify
the channel name.
[F3 (COPY)] Accesses the AUX/MAIN
COPY popup where you can
copy channel settings.
[F4 (LIBRARY) Accesses the AUX/MAIN LI-
BRARY popup where you can
use the channel library.
[F5 (GROUP ASSIGN)] Accesses the GROUP ASSIGN
popup where you can make
DCA group and MUTE group
assignments.
[F6 (PEAK CLEAR)] Clears the level meter peak
hold or over indication.
[F7 (COPY MAIN Copies the send amount from
MIX)] * each input channel to MAIN
L/R.
Switches between the MTX
[F7 ( MTX SENDS)]
SENDS display and the AUX
[F7 ( AUX SENDS)]
SENDS display. This exists
only for the MAIN L/R chan-
nel.
[F8 (Patchbay)] Accesses the PATCHBAY
screen.
* AUX channels only
If you press [F8 (Patchbay)] to access the PATCHBAY screen,
the currently selected channel will be highlighted in the
PATCHBAY screen.
Accessing the CHANNEL DISPLAY
screen
1.
In the fader module section, press [SEL] to select MAIN L/R
or an AUX channel.
The MAIN L channel or MAIN R channel will be selected
alternately each time you press MAIN [SEL].
62
2.
In the CHANNEL EDIT section, press [CH DISP] to access
the CHANNEL DISPLAY screen.
fig.ScrChAux.eps
p. 62
By pressing a different [SEL] while the CHANNEL DISPLAY
p. 51
screen is shown, you can switch to the display for that channel.
p. 63
If you've selected the "CHANNEL DISPLAY follows CH
SELECT" button located in the CHANNEL SELECT area of
User Preference (p. 155), pressing a [SEL] will recall the
p. 64
CHANNEL DISPLAY screen for that channel.
p. 54

Stereo-linking AUX channels

You can stereo-link adjacent odd-numbered and even-numbered
AUX channels so that their parameters will have the same settings.
This is convenient when you want stereo output.
p. 65
1.
Access the CHANNEL DISPLAY screen for the AUX channel
that you want to stereo-link.
2.
Press [F1 (LINK)].
p. 90
A confirmation message will appear, asking you to confirm the
stereo-link operation.
The function buttons have the following operations.
[F6 (CANCEL)]
[F7 (LINK (L <- R))]
[F8 (LINK (L -> R))]
3.
Press [F7 (LINK (L <- R))] or [F8](LINK (L -> R) ] , the AUX
channels will be stereo-linked.
Cancels the stereo-link operation
and closes the popup.
The parameters of the odd-num-
bered channel will be set to the val-
ues of the even-numbered channel.
The parameters of the even-num-
bered channel will be set to the val-
ues of the odd-numbered channel.