Mitsubishi Electric MR-J5-G-N1 User Manual page 147

■[Bit 10: OMS]
Setting value Name
1 (pp) Target reached
3 (pv)
4 (tq) Target reached (not
supported)
6 (hm) Target reached
8 (csp) 
9 (csv)
10 (cst)
*1
-100 (jg) Target reached
*1
-101 (pt)
*1 Available on servo amplifiers with firmware version B8 or later.
Description
0: Halt (Bit 8) = 0: Target position not reached.
0: Halt (Bit 8) = 1: Axis decelerates.
1: Halt (Bit 8) = 0: Target position reached.
1: Halt (Bit 8) = 1: Velocity of axis is 0.
Judgment condition of Target position reached:
When the time set in [Position window time (Obj. 6068h)] elapses in a state where the difference between the
values in [Position actual value (Obj. 6064h)] and [Target position (Obj. 607Ah)] is equal to or below the value set
in [Position window (Obj. 6067h)], the state becomes "Target position reached".
0: Halt (Bit 8) = 0: Target velocity not reached.
0: Halt (Bit 8) = 1: Axis decelerates.
1: Halt (Bit 8) = 0: Target velocity reached.
1: Halt (Bit 8) = 1: Velocity of axis is 0.
Judgment condition of Target velocity reached:
When the time set in [Velocity window time (Obj. 606Eh)] elapses in a state where the difference between the
values in [Velocity actual value (Obj. 606Ch)] and [Target velocity (Obj. 60FFh)] is equal to or below the value set
in [Velocity window (Obj. 606Dh)], the state becomes "Target velocity reached".
0: Halt (Bit 8) = 0: Target torque not reached.
0: Halt (Bit 8) = 1: Axis decelerates.
1: Halt (Bit 8) = 0: Target torque reached.
1: Halt (Bit 8) = 1: Velocity of axis is 0.
Judgment condition of Target torque reached:
When the time set in [Torque window time] elapses in a state where the difference between the values in [Torque
actual value (Obj. 6077h)] and [Target torque (Obj. 6071h)] is equal to or below the value set in [Torque window],
the state becomes "Target torque reached".
Bit 13 off/bit 12 off/bit 10 off: Homing procedure is in progress.
Bit 13 off/bit 12 off/bit 10 on: Homing procedure is interrupted or not started.
Bit 13 off/bit 12 on/bit 10 off: Homing is attained, but target is not reached.
Bit 13 off/bit 12 on/bit 10 on: Homing procedure is completed successfully.
Bit 13 on/bit 12 off/bit 10 off: Homing error occurred, velocity is not 0.
Bit 13 on/bit 12 off/bit 10 on: Homing error occurred, velocity is 0.
Bit 13 on/bit 12 on/bit 10 off: -

0: Halt (Bit 8) = 0: Target position not reached.
0: Halt (Bit 8) = 1: Axis decelerates.
1: Halt (Bit 8) = 0: Target position reached.
1: Halt (Bit 8) = 1: Velocity of axis is 0.
Judgment condition of Target position reached:
When the time set in [Position window time (Obj. 6068h)] elapses in a state where the difference between the
current position and the command position is equal to or below the value set in [Position window (Obj. 6067h)],
the state becomes "Target position reached".
0: Halt (Bit 8) = 0: Target position not reached.
0: Halt (Bit 8) = 1: Axis decelerates.
1: Halt (Bit 8) = 0: Target position reached.
1: Halt (Bit 8) = 1: Velocity of axis is 0.
Judgment condition of Target position reached:
When the time set in [Position window time (Obj. 6068h)] elapses in a state where the difference between the
current position and the point table command position is equal to or below the value set in [Position window (Obj.
6067h)], the state becomes "Target position reached".
10 PDS Control Objects
10.3 [Statusword (Obj. 6041h)]
11
145