HEIDENHAIN TNC 620 User Manual page 667

Incremental definition............ 438
Point definition....................... 436
Positioning behavior............... 441
Projection angle definition...... 431
Resetting................................ 428
Selection of possible solutions....
444
Spatial angle definition........... 429
Vector definition..................... 434
Plan view................................. 553
PLC and NC synchronization.... 331
Pocket table............................. 184
Polar coordinates...................... 102
Fundamentals......................... 102
Programming.......................... 236
Positioning................................ 542
With Manual Data Input......... 542
With tilted working plane....... 456
With tilted working plane....... 375
Preset table...................... 497, 512
Transferring test results.......... 512
Principal axes................... 101, 101
Probing a plane........................ 524
Probing cycles.......................... 507
Manual operating mode......... 507
Processing DXF data
Basic settings......................... 264
Filter for hole positions........... 276
Selecting a contour................ 269
Selecting hole positions
Single selection................ 273
Selecting machining positions 272
Setting layers......................... 266
Program.................................... 105
Editing.................................... 113
Opening a new program........ 109
Organization........................... 105
Structuring.............................. 150
Program call
Any desired program as
subprogram............................ 285
Program defaults...................... 393
Programming graphics............. 245
Programming tool movements. 110
Program run............................. 561
Execute.................................. 562
Interrupt................................. 563
Mid-program startup.............. 570
Optional block skip................. 574
Overview................................ 561
Resuming after interruption.... 566
Retraction............................... 567
Program-section repeat............ 283
Projection in three planes......... 553
Protection zone........................ 582
Pulsing spindle speed.............. 419
HEIDENHAIN | TNC 620 | Conversational Programming User's Manual | 10/2015
Q
Q parameter
Export..................................... 332
Transfer values to the
PLC................................ 331, 332
Q parameter programming.... 300,
347
Additional functions................ 314
Angle functions...................... 308
Calculation of circles.............. 309
If-then decisions..................... 310
Mathematical functions.......... 305
Programming notes....
302, 348, 349, 350, 352, 354
Q parameters................... 300, 347
Checking................................ 312
Local parameters QL.............. 300
Preassigned............................ 358
Residual parameters QR........ 300
R
Radius compensation............... 195
Entering.................................. 196
Outside corners, inside
corners................................... 197
Rapid traverse.......................... 172
Reading out machine parameters....
355
Reference system............ 101, 101
Replacing texts......................... 116
Resonance vibration................. 419
Retraction................................. 567
After a power interruption...... 567
Retraction from the contour..... 385
Returning to the contour.......... 572
Rotary axes.............................. 449
Rotary axis
Reduce display M94............... 451
Shortest-path traverse: M126. 450
Rounded corners...................... 227
Rounding corners M197........... 390
S
Save service files..................... 164
Screen keyboard...................... 146
Screen layout............................. 76
Search function........................ 116
Selecting a contour from DXF.. 269
Selecting positions from DXF... 272
Selecting the datum................. 104
Selecting the unit of measure.. 109
Select kinematics..................... 583
Set BAUD rate......................... 588
Set data transmission speed.... 588
Software number..................... 587
SPEC FCT................................ 392
Special functions...................... 392
SQL commands....................... 333
Status display............................. 80
Additional................................. 82
General..................................... 80
Straight line...................... 225, 237
String parameters.................... 347
Structuring programs................ 150
Subprogram.............................. 281
Superimposing handwheel
positioning M118...................... 383
Surface normal vector....
434, 448, 462,
Switch-off................................. 478
Switch-on................................. 476
T
TCPM....................................... 457
Reset...................................... 461
Teach In............................ 112, 225
Test Run................................... 558
Test run
Execute.................................. 560
Test Run
Overview................................ 558
test run
Setting speed......................... 549
Text File.................................... 410
Text file
Delete functions..................... 411
Finding text sections.............. 413
Opening and exiting............... 410
Text variables........................... 347
Tilted axes................................ 452
Tilting
Resetting................................ 428
Tilting the Working Plane....
425, 426,
Tilting the working plane
Manual................................... 535
Tilting without rotary axes........ 446
TNCguide................................. 165
TNCremo.................................. 592
TNCremoNT............................. 592
Tool carrier management.......... 395
Tool change.............................. 189
Tool compensation................... 194
Length.................................... 194
Tool Compensation
Radius.................................... 195
Tool compensation
Three-dimensional.................. 462
Tool data................................... 174
Call......................................... 187
Delta values........................... 175
Entering into the program...... 175
Enter into the table................ 176
Export..................................... 205
Import.................................... 205
Tool data
463
535
667