SELVA MARINE Wahoo 15 Service Manual page 287

Disassembling the gear pump ..................7-38
Disassembling the lower case ..................6-13
Disassembling the manual starter...............5-9
Disassembling the power tilt motor ...........7-31
Disassembling the propeller
shaft assembly ..........................................6-7
Disassembling the propeller
shaft housing assembly ............................6-7
Disassembling the starter motor ...............8-14
Disassembling the swivel bracket .............7-22
Disassembling the tiller handle ...................7-3
Disassembling the tilt cylinder...................7-43
Disassembling the upper case..................7-15
Disassembly and assembly ........................1-5
Draining the fuel..........................................3-3
Drive shaft and lower case........................6-11
E.
Electrical ......................................... 2-12
Electrical component and wiring
harness routing .........................................8-1
Engine electric control system ..................8-25
F.
Fire prevention ............................................1-4
Friction plate (tiller handle model)...............7-5
Fuel filter .....................................................4-2
Fuel hose, blowby hose, and
cooling water hose ....................................4-1
Fuel pump ...................................................4-4
Fuel system..............................2-11
G.
General .....................................................3-16
General specification ..................................2-1
General torque ..........................................2-33
Good working practice ................................1-5
H.
Hose routing................................................4-1
How to use this manual...............................1-1
I.
Identification................................................1-6
Ignition and ignition control system...........8-21
Ignition coil and Rectifier Regulator ..........5-17
Installing the carburetor ............................4-14
Installing the clamp bracket ............ 7-24
Installing the cylinder head .......................5-47
Installing the lower unit .............................6-17
Installing the power tilt unit........................7-28
6AG3J11
Installing the power unit............................ 5-61
Installing the propeller shaft housing ........ 6-16
Installing the shift rod,
drive shaft housing, and drive shaft........ 6-15
Installing the sprocket and timing belt ...... 5-31
Installing the starter motor ........................ 8-18
Installing the steering arm ........................ 7-18
Installing the upper case........................... 7-19
Installing the water pump.......................... 6-16
L.
Lower unit ...................... 2-12
Lubricating the outboard motor................. 3-18
M.
Maintenance interval chart ......................... 3-1
Maintenance specification .......................... 2-7
Manual format............................................. 1-1
,
2-21
Manual starter (manual starter model) ....... 5-7
Measuring the forward and
reverse gear backlash ............................ 6-23
Measuring the peak voltage ..................... 8-11
Model.......................................................... 1-6
P.
Part, lubricant, and sealant......................... 1-4
Port view..................................................... 8-7
Power tilt cylinder (power tilt model)......... 7-41
Power tilt electrical system
(power tilt model) .................................... 7-47
, ,
2-19 3-2
Power tilt gear pump (power tilt model) .... 7-35
Power tilt motor (power tilt model) ............ 7-30
Power unit........................ 2-7
Power unit (check and adjustment) ............ 5-1
Power unit assembly
(remote control model) ........................... 5-15
Power unit assembly
(tiller handle model) ................................ 5-13
Precaution when transporting or
storing the outboard motor ..................... 1-19
Predelivery check ..................................... 1-12
Propeller selection .................................... 1-12
Propeller shaft housing............................... 6-6
Propeller size............................................ 1-12
R.
Refacing the valve seat ............................ 5-41
Removing the carburetor .......................... 4-12
,
7-28
Removing the clamp bracket ...........7-22
Removing the cylinder head ..................... 5-37
Removing the drive shaft,
drive shaft housing, and shift rod............ 6-12
Index
1
2
, , ,
2-20 3-14 6-1
3
4
5
6
, , ,
2-16 3-3 5-13
7
8
9
,
7-27
i-3