Comtech EF Data SNM-1001L Installation And Operation Manual page 287

SNM-1001L Satellite Modem
Remote Control Operation
AUPC Command:
Maximum Response:
Power Limit Status:
Response:
AUPC Command:
Minimum Response:
Power Limit Status:
Response:
AUPC Command:
Eb/N0 Response:
Target Set Status:
Point Response:
AUPC Command:
Maximum Response:
Tracking Status:
Rate Response:
AUPC Local Command:
Carrier Loss Response:
Action Status:
Response:
AUPC Command:
Remote Response:
Carrier Loss Status:
Action Response:
Remote Notes:
Modem 1. Always wait 3 seconds between consecutive remote modem command/status polls.
AUPC 2. If Local AUPC is not enabled, status commands will return last known condition. They will also request status
Commands from the remote modem. This allows a second request to return proper status.
Remote Command:
AUPC Response:
Enable
Remote Command:
Interface Response:
Substitution Status:
Pattern Response:
Remote Command:
Interface Response:
Baseband Status:
Loopback Response:
<add/MAXP_snn.n'cr'
>add/MAXP_snn.n'cr''lf']
<add/MAXP_'cr'
>add/MAXP_snn.n'cr''lf']
<add/MINP_snn.n'cr'
>add/MINP_snn.n'cr''lf']
<add/MINP_'cr'
>add/MINP_snn.n'cr''lf']
<add/ENSP_nn.n'cr'
>add/ENSP_nn.n'cr''lf']
<add/ENSP_'cr'
>add/ENSP_nn.n'cr''lf']
<add/MAXT_n.n'cr'
>add/MAXT_n.n'cr''lf']
<add/MAXT_'cr'
>add/MAXT_n.n'cr''lf']
<add/LCL_xxxx'cr'
>add/LCL_xxxx'cr''lf']
<add/LCL_'cr'
>add/LCL_xxxx'cr''lf']
<add/RCL_xxxx'cr'
>add/RCL_xxxx'cr''lf']
<add/RCL_'cr'
>add/RCL_xxxx'cr''lf']
<add/RPC_xxx'cr'
>add/RPC_xxx'cr''lf'
<add/RISP_xxx'cr'
>add/RISP_xxx'cr''lf']
<add/RISP_'cr'
>add/RISP_xxx'cr''lf']
<add/RBBL_xxx'cr'
>add/RBBL_xxx'cr''lf']
<add/RBBL_'cr'
>add/RBBL_xxx'cr''lf']
Where: snn.n = -30.0 to -5.0, in 0.1 steps (nominal range
in dBm).
Notes:
1. The nominal power range is modified relative to
the value specified by the modulator power offset
(MPO_).
2. ASYNC or AUPC Overhead only.
Where: snn.n = -30.0 to -5.0, in 0.1 steps (nominal range
in dBm).
Notes:
1. The nominal power range is modified relative to
the value specified by the modulator power offset
(MPO_).
2. ASYNC or AUPC Overhead only.
Where: nn.n = 3.2 to 16.0, in 0.1 increments (Eb/N0 in
dB).
Note: AUPC Overhead only.
Where: n.n = 0.5 to 6.0, in 0.5 increments (max tracking
rate in dBm/minute).
Note: AUPC Overhead only.
Where: xxxx = HOLD, NOM, or MAX (power level setting
when local carrier loss).
Note: AUPC Overhead only.
Where: xxxx = HOLD, NOM, or MAX (power level setting
when remote carrier loss).
Note: AUPC Overhead only.
Where: xxx = ON or OFF (remote AUPC enable).
Note: AUPC Overhead only.
Where: xxx = ON or OFF (remote transmit 2047 pattern
enable).
Notes:
1. Transmit 2047 Pattern.
2. AUPC Overhead only.
Where: xxx = ON or OFF (remote baseband loopback
enable).
Note: ASYNC or AUPC Overhead only.
B–13
Revision 1
MN/SNM1001L.IOM