Comtech EF Data SNM-1001L Installation And Operation Manual page 282

SNM-1001L Satellite Modem
Remote Control Operation
Demodulator Command:
Rate Variable Response:
Assignment
& Selection Status:
Descramble Command:
Enable Response:
Status:
Response:
Differential Command:
Decoder Response:
Enable Status:
Response:
IF Loopback Command:
TX L-Band Response:
modem Status:
Response:
Sweep Command:
Center Response:
Frequency Status:
Response:
Sweep Width Command:
Range Response:
Status:
Response:
Sweep Command:
Reacquisi- Response:
tion Status:
Response:
Bit Error Rate Command:
Threshold Response:
Status:
Response:
Demodulator Command:
Type Response:
Status:
Response:
Demodulator Command:
Decoder Response:
Type Status:
Response:
Demodulator Command:
Spectrum Response:
Rotation Status:
Response:
Reed- Command:
Solomon Response:
Decoder
Enable Status:
Response:
Receive Command:
BPSK Data Response:
Ordering Status:
Response:
<add/SDRV_nnnn_mmmm.mmm'cr'
>add/SDRV_nnnn_mmmm.mmm'cr''lf']
See DR command.
<add/DE_xxx'cr'
>add/DE_xxx'cr''lf']
<add/DE_'cr'
>add/DE_xxx'cr''lf']
<add/DDEC_xxx'cr'
>add/DDEC_xxx'cr''lf']
<add/DDEC_'cr'
>add/DDEC_xxx'cr''lf']
<add/IFL_xxx'cr'
>add/IFL_xxx'cr''lf']
<add/IFL_'cr'
>add/IFL_xxx'cr''lf']
<add/SCF_snnnnn'cr'
>add/SCF_snnnnn'cr''lf']
<add/SCF_'cr'
>add/SCF_snnnnn'cr''lf']
<add/SWR_nnnnnn'cr'
>add/SWR_nnnnnn'cr''lf']
<add/SWR_'cr'
>add/SWR_nnnnnn'cr''lf']
<add/SR_xxx'cr'
>add/SR_xxx'cr''lf']
<add/SR_'cr'
>add/SR_xxx'cr''lf']
<add/BERT_xxxx'cr'
>add/BERT_xxxx'cr''lf']
<add/BERT_'cr'
>add/BERT_xxxx'cr''lf']
<add/DT_xxxx'cr'
>add/DT_xxxx'cr''lf']
<add/DT_'cr'
>add/DT_xxxx'cr''lf']
<add/DDT_xxx'cr'
>add/DDT_xxx'cr''lf']
<add/DDT_'cr'
>add/DDT_xxx'cr''lf']
<add/DSR_xxx'cr'
>add/DSR_xxx'cr''lf']
<add/DSR_'cr'
>add/DSR_xxx'cr''lf']
<add/RSDE_xxx'cr'
>add/RSDE_xxx'cr'lf']
<add/RSDE_'cr'
>add/RSDE_xxx'cr'lf']
<add/RDA_xxx'cr'
>add/RDA_xxx'cr''lf']
<add/RDA_xxx'cr'
>add/RDA_xxx'cr''lf']
Where:
nnnn = 1/2 (QPSK 1/2 Turbo and non-Turbo),
[coder rate], 3/4 (QPSK 3/4 Turbo and non-
Turbo), 7/8 (QPSK 7/8), BP12 (BPSK ½), 8P23
(8PSK 2/3), OQ12 (OQPSK 1/2 Turbo and non-
Turbo), OQ34 (OQPSK 3/4 Turbo and non-Turbo),
OQ78 (OQPSK 7/8), BPSK (BPSK1/1 Turbo and
non-Turbo), QPSK (QPSK 1/1 Turbo and non-
Turbo), OQSK (OQPSK 1/1 Turbo, and non-
Turbo), 2144 (BPSK 21/44 Turbo Only), B516
(BPSK 5/16 Turbo Only), and 8P34 (8PSK 3/4
Turbo Only).
mmmm.mmm = Data rate in kHz
Burst Mode = nnnn= 1/2
mmmm.nnn = 19.2 or 57.6 kbps
Where: xxx = ON or OFF.
Where: xxx = ON or OFF.
Where: xxx = ON or OFF.
Where: snnnnn = -75000 to +75000, in 1 Hz steps.
Where: nnnnnn = 0 to 150000, in 1 Hz steps.
Where: xxx = 0 to 999 (number of seconds).
Where: xxxx = NONE, or 1E-n, where n = 3, 4, 5, 6, 7,
or 8 (exponent of threshold).
Where: xxxx = INTL (INTELSAT OPEN NETWORK),
EFD (EF DATA CLOSED NETWORK), CSC
(COMSTREAM CLOSED NETWORK), FDC
(FAIRCHILD CLOSED NETWORK).
Where: xxx = VIT (K-7 VITERBI ENCODER), SEQ
(SEQUENTIAL ENCODER) or TUR (TURBO).
Where: xxx = NRM (normal spectrum), INV (inverted
spectrum).
Where: xxx = ON, OFF, or CORR_OFF.
Where: xxx = NRM (STANDARD), INV (NON-
STANDARD).
B–8
Revision 1
MN/SNM1001L.IOM