Comtech EF Data SNM-1001L Installation And Operation Manual page 284

SNM-1001L Satellite Modem
Remote Control Operation
Receive Command:
Clock Response:
Phase Status:
Response:
Baseband Command:
Loopback Response:
Status:
Response:
Interface Command:
Loopback Response:
Status:
Response:
Interface Command:
Loop Timing Response:
Status:
Response:
Interface Buffer size programming is supported in two formats; bits, or milli-seconds. The selected format must be chosen
Buffer Size using the buffer programming command (IBP_). If the buffer is to be programmed in milli-seconds and
plesiochronous slips are required use the receive framing structure command (IRFS_) to define the proper framing
format.
Interface Command:
Buffer Size Response:
(Bit Format) Status:
Response:
Interface Command:
Buffer Size Response:
(Milli- Status:
second Response:
Format)
Interface Command:
Buffer Response:
Center
Interface Command:
Buffer Response:
Program-
ming Status:
Response:
Interface Command:
Receive Response:
Farming Status:
Structure Response:
Interface Command:
Substitute Response:
Pattern Status:
Response:
Interface Command:
Read Error Response:
Select Status:
Response:
Transmit Command:
Data Fault Response:
Status:
Response:
Receive Command:
Data Fault Response:
Status:
Response:
<add/RCP_xxx'cr'
>add/RCP_xxx'cr''lf']
<add/RCP_'cr'
>add/RCP_xxx'cr''lf']
<add/BBL_xxx'cr'
>add/BBL_xxx'cr''lf']
<add/BBL_'cr'
>add/BBL_xxx'cr''lf']
<add/ILB_xxx'cr'
>add/ILB_xxx'cr''lf']
<add/ILB_'cr'
>add/ILB_xxx'cr''lf']
<add/ILT_xxx'cr'
>add/ILT_xxx'cr''lf']
<add/ILT_'cr'
>add/ILT_xxx'cr''lf']
<add/IBS _nnnnnn'cr'
>add/IBS _nnnnnn'cr''lf']
<add/IBS _'cr'
>add/IBS _nnnnnn'cr''lf']
<add/IBS _nn'cr'
>add/IBS _nn'cr''lf']
<add/IBS _'cr'
>add/IBS _nn'cr''lf']
<add/IBC_'cr'
>add/IBC_'cr''lf']
<add/IBP_xxxx'cr'
>add/IBP_xxxx'cr''lf']
<add/IBP_'cr'
>add/IBP_xxxx'cr''lf']
<add/IRFS_ff_ssss'cr'
>add/IRFS_ff_ssss'cr''lf']
<add/IRFS_ff'cr'
>add/IRFS_ff_ssss'cr''lf']
<add/ISP_xxxxxx'cr'
>add/ISP_xxxxxx'cr''lf']
<add/ISP_'cr'
>add/ISP_xxxxxx'cr''lf'
<add/IRE_xxxxxx'cr'
>add/IRE_xxxxxx'cr''lf']
<add/IRE_'cr'
>add/IRE_xxxxxx'cr''lf']
<add/TDF_xxxx'cr'
>add/TDF_xxxx'cr''lf']
<add/TDF_'cr'
>add/TDF_xxxx'cr''lf']
<add/RDF_xxxx'cr'
>add/RDF_xxxx'cr''lf']
<add/RDF_'cr'
>add/RDF_xxxx'cr''lf']
Where: xxx = NRM (normal clock phasing), INV
(inverted clock phasing).
Where: xxx = ON or OFF.
Where: xxx = ON or OFF.
Where: xxx = ON or OFF.
Where: nnnnnn = 32 to 262144, in 16 bit
increments.
Where: nn = 0 to 99 (buffer size in milli-seconds).
Note: For Drop & Insert:
1. nn = 7.5, 15, or 30 (milli-seconds) for
E1CAS format.
2. nn = 6, 12, 24, or 30 (milli-seconds) for
T1S/T1ESFS format.
3. nn = 1, 2, 4, 8, 16, or 32 (milli-seconds)
for all other D&I formats.
Where: xxxx = BITS or MS (milli-seconds).
Where:
ff = T1 or E1 (frame type).
ssss = NONE or G704 (framing structure).
Where: xxxxxx = ON or OFF.
Note: Transmit 2047 Pattern.
Where: xxxxxx = ON or OFF.
Note: Receive 2047 Pattern.
Where: xxxx = NONE, DATA, or AIS.
Where: xxxx = NONE, DATA, or AIS.
B–10
Revision 1
MN/SNM1001L.IOM