Table 5-4: Proxy & Registration Parameters (Continues On Pages 72 To 78) - AudioCodes Mediant 1000 User Manual

Table 5-4: Proxy & Registration Parameters (continues on pages 72 to 78)
Parameter
Enable Proxy
[IsProxyUsed]
Proxy Name
[ProxyName]
Proxy IP Address
[ProxyIP]
First Redundant Proxy IP
Address
[ProxyIP]
Second Redundant Proxy
IP Address
[ProxyIP]
SIP User's Manual
Description
Don't Use Proxy [0] = Proxy isn't used, the internal routing table is used instead
(default).
Use Proxy [1] = Proxy is used.
If you are using a Proxy server, enter the IP address of the primary Proxy server in
the Proxy IP address field.
If you are not using a Proxy server, you must configure the Tel to IP Routing table on
the gateway (described in Section
Defines the Home Proxy Domain Name.
If specified, the Proxy Name is used as Request-URI in REGISTER, INVITE and
other SIP messages. If not specified, the Proxy IP address is used instead.
IP address (and optionally port number) of the primary Proxy server you are using.
Enter the IP address as FQDN or in dotted format notation (for example 201.10.8.1).
You can also specify the selected port in the format: <IP Address>:<port>.
This parameter is applicable only if you select 'Yes' in the 'Is Proxy Used' field.
If you enable Proxy Redundancy (by setting EnableProxyKeepAlive=1 or 2), the
gateway can work with up to four Proxy servers. If there is no response from the
primary Proxy, the gateway tries to communicate with the redundant Proxies. When
a redundant Proxy is found, the gateway either continues working with it until the
next failure occurs or reverts to the primary Proxy (refer to the 'Redundancy Mode'
parameter). If none of the Proxy servers respond, the gateway goes over the list
again.
The gateway also provides real time switching (hotswap mode), between the primary
and redundant proxies ('IsProxyHotSwap=1'). If the first Proxy doesn't respond to
INVITE message, the same INVITE message is immediately sent to the second
Proxy.
Note 1: If 'EnableProxyKeepAlive=1 or 2', the gateway monitors the connection with
the Proxies by using keep-alive messages (OPTIONS or REGISTER).
Note 2: To use Proxy Redundancy, you must specify one or more redundant
Proxies using multiple 'ProxyIP= <IP address>' definitions.
Note 3: When port number is specified (e.g., domain.com:5080), DNS NAPTR/SRV
queries aren't performed, even if ProxyDNSQueryType is set to 1 or 2.
IP addresses of the first redundant Proxy you are using.
Enter the IP address as FQDN or in dotted format notation (for example
192.10.1.255). You can also specify the selected port in the format: <IP
Address>:<port>.
Note 1: This parameter is available only if you select 'Use Proxy' in the 'Enable
Proxy' field.
Note 2: When port number is specified, DNS NAPTR/SRV queries aren't performed,
even if ProxyDNSQueryType is set to 1 or 2.
ini file note: The IP address of the first redundant Proxy is defined by the second
repetition of the ini file parameter 'ProxyIP'.
IP addresses of the second redundant Proxy you are using.
Enter the IP address as FQDN or in dotted format notation (for example
192.10.1.255). You can also specify the selected port in the format: <IP
Address>:<port>.
Note 1: This parameter is available only if you select 'Use Proxy' in the 'Enable
Proxy' field.
Note 2: When port number is specified, DNS NAPTR/SRV queries aren't performed,
even if ProxyDNSQueryType is set to 1 or 2.
ini file note: The IP address of the second redundant Proxy is defined by the third
repetition of the ini file parameter 'ProxyIP'.
5.5.4.2 on page 107).
72
Mediant 1000
Document #: LTRT-83301