Table 5-30: Media Settings, Rtp / Rtcp Parameters (Continues On Pages 156 To 157) - AudioCodes Mediant 1000 User Manual

SIP User's Manual
Table 5-30: Media Settings, RTP / RTCP Parameters (continues on pages 155 to 156)
Parameter
Dynamic Jitter Buffer Minimum Delay
[DJBufMinDelay]
Dynamic Jitter Buffer Optimization
Factor
[DJBufOptFactor]
RTP Redundancy Depth
[RTPRedundancyDepth]
Packing Factor
[RTPPackingFactor]
Basic RTP Packet Interval
[BasicRTPPacketInterval]
RTP Directional Control
[RTPDirectionControl]
RFC 2833 TX Payload Type
[RFC2833TxPayloadType]
RFC 2833 RX Payload Type
[RFC2833RxPayloadType]
RFC 2198 Payload Type
[RFC2198PayloadType]
Fax Bypass Payload Type
[FaxBypassPayloadType]
Enable RFC 3389 CN Payload Type
[EnableStandardSIDPayloadType]
Comfort Noise Generation
Negotiation
[ComfortNoiseNegotiation]
Analog Signal Transport Type
[AnalogSignalTransportType]
Version 5.0
Description
Minimum delay for the Dynamic Jitter Buffer.
The valid range is 0 to 150 milliseconds.
The default delay is 10 milliseconds.
Note: For more information on the Jitter Buffer, refer to Section
page 283.
Dynamic Jitter Buffer frame error / delay optimization factor.
The valid range is 0 to 13.
The default factor is 10.
Note 1: Set to 13 for data (fax and modem) calls.
Note 2: For more information on the Jitter Buffer, refer to Section
page 283.
[0] = Disable the generation of redundant packets (default).
[1] = Enable the generation of RFC 2198 redundancy packets.
N/A.
Controlled internally by the gateway according to the selected coder.
N/A.
Controlled internally by the gateway according to the selected coder.
Note: This parameter should not be used. Use the 'Coders' screen under
'Protocol Definition' instead.
N/A.
Controlled internally by the gateway according to the selected coder.
N/A.
Use the ini file parameter RFC2833PayloadType instead.
N/A.
Use the ini file parameter RFC2833PayloadType instead.
RTP redundancy packet payload type, according to RFC 2198.
The range is 96-127. The default is 104.
Applicable if 'RTP Redundancy Depth=1'
Determines the fax bypass RTP dynamic payload type.
The valid range is 96 to 120. The default value is 102.
Determines whether Silence Indicator (SID) packets that are sent and
received are according to RFC 3389.
Disable [0] = G.711 SID packets are sent in a proprietary method
(default).
Enable [1] = SID (comfort noise) packets are sent with the RTP SID
payload type according to RFC 3389. Applicable to G.711 and G.726
coders.
Enables negotiation and usage of Comfort Noise (CN).
Valid options include:
0 = Disable (default)
1 = Enable Comfort Noise negotiation
The use of CN is indicated by including a payload type for CN on the
media description line of the SDP. The gateway can use CN with a codec
whose RTP timestamp clock rate is 8,000 Hz (G.711/G.726). The static
payload type 13 is used. The use of CN is negotiated between sides;
therefore, if the remote side doesn't support CN, it is not used.
Note: Silence Suppression must be enabled to generate CN.
Ignore analog signals [0] = Hook-flash isn't transferred to the remote side
(default).
RFC 2833 analog signal relay [1] = Hook-flash is transferred via RFC
2833.
155
5. Web Management
9.7 on
9.7 on
December 2006