AudioCodes Mediant 1000 User Manual page 86

Table 5-7: Advanced Parameters, General Parameters (continues on pages 85 to 90)
Parameter
Enable Digit Delivery to Tel
[EnableDigitDelivery]
Enable DID Wink
[EnableDIDWink]
Delay Before DID Wink
[DelayBeforeDIDWink]
Reanswer Time
[RegretTime]
SIP User's Manual
Description
Disable [0] = Disabled (default).
Enable [1] = Enable Digit Delivery feature for Mediant 1000.
The digit delivery feature enables sending of DTMF digits to the gateway's port
after the call was answered. For IPàTel calls, after answering the call, the
Mediant 1000 plays the DTMF digits (of the called number) towards the phone
line.
Note 1: The called number can include characters 'p' (1.5 seconds pause) and
'd' (detection of dial tone). If character 'd' is used, it must be the first 'digit' in the
called number. The character 'p' can be used several times.
For example (for FXS/FXO module), the called number can be as follows:
d1005, dpp699, p9p300. To add the 'd' and 'p' digits, use the usual number
manipulation rules.
Note 2: To use this feature with FXO modules, configure the gateway to
operate in one stage dialing mode.
Note 3: If the parameter 'EnableDigitDelivery' is enabled, it is possible to
configure the FXS/FXO gateway to wait for dial tone per destination phone
number (before or during dialing of destination phone number), therefore, the
parameter 'IsWaitForDialTone' (configurable for the entire gateway) is ignored.
Note 4: For digital modules, if the called number in IP-to-Tel call includes the
characters 'w' or 'p', the gateway places a call with the first part of the called
number (before 'w' or 'p') , and plays DTMF digits after the call is answered. If
the character 'w' is used, the gateway waits for detection of dial tone before it
starts playing DTMF digits. For example, if the number '1007766p100' is
defined as the called number, the gateway places a call with 1007766 as the
destination number, then, after the call is answered, it waits for 1.5 seconds and
plays the rest of the number (100) as DTMF digits.
Other examples: 1664wpp102, 66644ppp503, 7774w100pp200.
Note 5: The FXS and digital modules send SIP 200 OK responce only after the
DTMF dialing has completed.
Disable [0] = DID is disabled (default).
Enable [1] = Enable DID.
If enabled, the Mediant 1000 can be used for connection to EIA/TIA-464B DID
Loop Start lines. Both FXO (detection) and FXS (generation) are supported.
An FXO module dials DTMF digits after a Wink signal is detected (instead of a
Dial tone).
An FXS module generates the Wink signal after the detection of offhook
(instead of playing a Dial tone).
Defines the time interval (in seconds) between detection of offhook and
generation of DID Wink. Applicable only to FXS modules.
The valid range is 0 to 1,000. The default value is 0.
Analog: The time period after user hangs up the phone and before call is
disconnected (FXS). Also called regret time.
Digital: Determines the time period (in seconds) the gateway waits for an
MFC R2 Resume (Reanswer) signal once a Suspend (Clear back) signal
was received from the PBX. If this timer expires, the call is released..
Applicable only for MFC R2 CAS Brazil variant.
The valid range is 0 to 255 (in seconds). The default value is 0.
86
Mediant 1000
Document #: LTRT-83301