Table of Contents
Advertisement
Index
Station Address Setting Error ................................................. 221
Stationary Auto-Tuning..........................................................95
Stationary Auto-Tuning for Line-to-Line Resistance ........................94
Status Display .....................................................................90
Stopping Method Selection.................................................... 101
Storage Temperature .............................................................38
Supported Properties of Objects .............................................. 339
Surrounding Area .................................................................38
SvE ............................................................................... 219
T
T1-03 ...............................................................................96
T1-04 ...............................................................................96
T1-05 ...............................................................................96
T1-06 ...............................................................................96
T1-07 .......................................................................... 96, 97
TdE ............................................................................... 219
Terminal A1 Bias Setting...................................................... 143
Terminal A1 Function Selection.............................................. 143
Terminal A1 Gain Setting ..................................................... 143
Terminal A1 Signal Level Selection ......................................... 142
Terminal A2 Bias Setting...................................................... 145
Terminal A2 Function Selection.............................................. 145
Terminal A2 Gain Setting ..................................................... 145
Terminal A2 Signal Level Selection ......................................... 144
Terminal A3 Bias Setting...................................................... 144
Terminal A3 Function Selection.............................................. 144
Terminal A3 Gain Setting ..................................................... 144
Terminal A3 Signal Level Selection ......................................... 144
Terminal Block Configuration ..................................................52
Terminal Board Not Connected............................................... 206
Test Run....................................................................... 94, 97
Through Mode .................................................................. 139
TIM ............................................................................... 219
Time Data Error................................................................. 219
Time Not Set .................................................................... 219
Time to Continue Making Fault Restarts .................................... 302
Too Many Speed Search Restarts............................................. 218
Torque Compensation Gain ............................................. 122, 200
Torque Compensation Primary Delay Time ................................ 200
Torque Detection ............................................................... 147
Torque Detection 1 ............................................................. 139
Torque Detection Level 1................................................ 159, 302
Torque Detection Selection 1 ........................................... 158, 302
Torque Detection Time 1 ................................................ 159, 302
Troubleshooting without Fault Display...................................... 236
Tuning Errors.................................................................... 201
Types of Alarms, Faults, and Errors ......................................... 201
Types of Auto-Tuning for Induction Motors..................................94
U
U1-07 ............................................................................. 236
U2-oo, U3-oo, and UB-oo Initialization ..................................... 165
UL3 ......................................................................... 219, 228
UL5 ............................................................................... 220
UL Standards Compliance.......................................................54
Undertorque Detection 1................................................. 219, 228
Undertorque Detection Operation ............................................ 158
Undervoltage .................................................................... 228
Undervoltage Protection ....................................................... 273
438
Unexpected Noise from Connected Machinery............................. 241
Unit Capacity Setting Fault.................................................... 229
Unit Code ........................................................................ 165
Up/Down Command Operation............................................... 134
Up Arrow Key.....................................................................79
User Monitor Selection after Power Up ..................................... 163
User-Set Display Units Decimal Display.................................... 165
User-Set Display Units Maximum Value.................................... 165
User-Set Speed Agree 1........................................................ 137
User-Set Speed Agree 2........................................................ 139
Uv ................................................................................. 228
Uv1 ............................................................................... 220
Uv2 ............................................................................... 220
Uv3 ............................................................................... 220
V
V/f Characteristics .............................................................. 273
V/f Control.........................................................................25
V/f Control Mode Tuning ..................................................... 200
V/f Control Mode Tuning Parameters ....................................... 200
V/f Data Setting Error.......................................................... 231
V/f Gain During Speed Search................................................ 105
V/f Pattern Selection ........................................................... 127
Verifying Parameter Changes ...................................................87
Voltage drop calculation formula...............................................54
Voltage Reduction Rate.................................................. 167, 307
Voltage Restoration Complete Level .................................. 168, 307
Voltage Restoration Level ............................................... 167, 307
Voltage Restoration Sensitivity Time Constant ...................... 168, 307
Voltage Restoration Time Constant at Impact ........................ 168, 307
W
Waiting for Run ................................................................. 228
Warranty Information ............................................................22
Welded K3 Contactor Fault Select ........................................... 186
Wiring the Control Circuit Terminal ...........................................67
Writing BACnet Bypass Parameters ......................................... 346
Writing to Multiple Registers ................................................. 363
WrUn ............................................................................. 228
Z
Z: Bypass Parameters .......................................................... 176
Zero Servo Fault ................................................................ 219
Zero Speed....................................................................... 136
YASKAWA SIEP YAIZ1D 01C Z1000U HVAC MATRIX Drive Bypass Technical Manual
Advertisement
Chapters
Table of Contents
