YASKAWA Z1000U Technical Manual page 427

No.
L5-03 Time to Continue Making Fault Restarts
L5-04 Fault Reset Interval Time
L5-05 Fault Reset Operation Selection
L6-01 Torque Detection Selection 1
L6-02 Torque Detection Level 1
L6-03 Torque Detection Time 1
L6-13 Motor Underload Protection Selection
Motor Underload Protection Level at Minimum
L6-14
Frequency
L8-02 Overheat Alarm Level
L8-05 Input Phase Loss Protection Selection
L8-06 Input Phase Loss Detection Level
L8-07 Output Phase Loss Protection
L8-09 Output Ground Fault Detection Selection
L8-38 Carrier Frequency Reduction Selection
n1-01 Hunting Prevention Selection
n1-02 Hunting Prevention Gain Setting
n3-13 Overexcitation Deceleration Gain
o1-01
Drive Mode Unit Motor Selection
o1-02
User Monitor Selection after Power Up
o1-03 Digital Operator Display Selection
o1-09 Frequency Reference Display Units
o1-10 User-Set Display Units Maximum Value
o1-11 User-Set Display Units Decimal Display
o2-04 Drive Model Selection
o4-03 Cooling Fan Maintenance Operation Time Setting
o4-11 UB-9 to UB-16 Initialization
o4-19 Power Unit Price
S1-01 Stillness Control Selection
S1-02 Voltage Reduction Rate
S1-03 Voltage Restoration Level
S1-04 Voltage Restoration Complete Level
S1-05 Voltage Restoration Sensitivity Time Constant
S1-06 Voltage Restoration Time Constant at Impact
S2-01 Sequence Timer 1 Start Time
S2-02 Sequence Timer 1 Stop Time
S2-03 Sequence Timer 1 Day Selection
S2-04 Sequence Timer 1 Selection
S2-05 Sequence Timer 1 Reference Source
S2-06 Sequence Timer 2 Start Time
S2-07 Sequence Timer 2 Day Selection
S2-08 Sequence Timer 2 Day Selection
S2-09 Sequence Timer 2 Selection
S2-10 Sequence Timer 2 Reference Source
S2-11 Sequence Timer 3 Start Time
S2-12 Sequence Timer 3 Stop Time
S2-13 Sequence Timer 3 Day Selection
S2-14 Sequence Timer 3 Selection
S2-15 Sequence Timer 3 Reference Source
S2-16 Sequence Timer 4 Start Time
YASKAWA SIEP YAIZ1D 01C Z1000U HVAC MATRIX Drive Bypass Technical Manual
User
Name
Setting
<1>
<1>
No. Name
S2-17 Sequence Timer 4 Stop Time
S2-18 Sequence Timer 4 Day Selection
S2-19 Sequence Timer 4 Selection
S2-20 Sequence Timer 4 Reference Source
T1-01 Auto-Tuning Mode Selection
T1-02 Motor Rated Power
T1-03 Motor Rated Voltage
T1-04 Motor Rated Current
T1-05 Motor Base Frequency
T1-06 Number of Motor Poles
T1-07 Motor Base Speed
T1-11 Motor Iron Loss
Z1-01
Initialize
Z1-02
Password
Z1-03
Password Change
Z1-05
Auto Transfer to Bypass Upon Drive Fault
Z1-06
Power-Up Mode
Z1-07
Speed Reference Select
Z1-08
Run Command Select
Z1-09
HAND Mode Drive Speed Reference
Z1-10
Smoke Purge Preset Frequency Reference
Z1-11
2-Motor AND/OR Function Select
Z1-12
Run Delay Time
Z1-13
Pre-Interlock Run Select
Z1-14
Run Delay Frequency Reference
Z1-15
Interlock Wait Time
Z1-24
Contactor Open Delay Time
Z1-25
Contactor Close Delay Time
Z1-27
Phase Loss Brownout Voltage Level
Z1-28
Phase Loss Brownout Detection Time
H.3 User Setting Table
User
Setting
427
H