YASKAWA Z1000U Technical Manual page 435

Motor Hunting and Oscillation Control Parameters ....................... 200
Motor Iron Loss .............................................................98, 310
Motor is Too Hot ............................................................... 239
Motor No-Load Current........................................................ 131
Motor Overheat ................................................................. 226
Motor Overheat Alarm (PTC Input).......................................... 215
Motor Overheat Fault (PTC Input) ........................................... 216
Motor Overload ................................................................. 216
Motor Overload Estimate (oL1) .............................................. 317
Motor Overload Protection Selection ........................................ 150
Motor Overload Protection Time ............................................. 151
Motor Performance Fine-Tuning ............................................. 200
Motor Poles........................................................................96
Motor Protection ................................................................ 150
Motor q-Axis Current at Previous Fault ..................................... 315
Motor Rated Current ............................................ 96, 98, 131, 310
Motor Rated Power .........................................................97, 310
Motor Rated Voltage .................................................. 96, 97, 310
Motor Rotates in One Direction Only........................................ 239
Motor Underload Protection Level at Minimum Frequency ........ 160, 303
Motor Underload Protection Selection................................. 159, 302
Motor Wiring......................................................................56
Multi-Function Analog Inputs ................................................ 142
Multi-Function Analog Input Selection Error............................... 230
Multi-Function Analog Input Terminal Settings ........................... 143
Multi-Function Analog Outputs .............................................. 148
Multi-Function Analog Output Terminal AM Bias ........................ 149
Multi-Function Analog Output Terminal AM Gain........................ 149
Multi-Function Analog Output Terminal AM Monitor Selection........ 148
Multi-Function Analog Output Terminal AM Signal Level Selection .. 149
Multi-Function Analog Output Terminal FM Bias......................... 148
Multi-Function Analog Output Terminal FM Gain ........................ 148
Multi-Function Analog Output Terminal FM Monitor Selection ........ 148
Multi-Function Analog Output Terminal FM Signal Level Selection... 149
Multi-Function Digital Input Terminal Settings ............................ 133
Multi-Function Digital Outputs ............................................... 135
Multi-Function Input Selection Error ........................................ 229
Multi-Step Speed Selection.................................................... 124
N
n1-02.............................................................................. 200
N2 Configuration ............................................................... 402
N2 Serial Communication ..................................................... 405
N2 Setup Parameters ........................................................... 405
N2 Specifications ............................................................... 402
Network Digital Input Select.................................................. 193
Network Termination .............................................. 334, 355, 404
No-Load Current Alarm ....................................................... 232
No-Load Current Error......................................................... 233
Notes on Stationary Auto-Tuning ..............................................95
nSE ............................................................................... 212
Number of Auto Restart Attempts...................................... 156, 302
Number of Motor Poles ....................................................98, 310
Number of Run Commands ................................................... 317
Number of Speed Search Restarts ............................................ 107
O
oC ................................................................................. 212
oFA00 ............................................................................ 213
oFA01 ............................................................................ 213
YASKAWA SIEP YAIZ1D 01C Z1000U HVAC MATRIX Drive Bypass Technical Manual
oFA03 to oFA06 ................................................................ 213
oFA10 ............................................................................ 213
oFA11 ............................................................................ 213
oFA12 to oFA17 ................................................................ 213
oFA30 to oFA43 ................................................................ 213
oFb00 ............................................................................. 214
oFb01 ............................................................................. 214
oFb02 ............................................................................. 214
oFb03 to oFb11 ................................................................. 214
oFb12 to oFb17 ................................................................. 214
oFC00 ............................................................................ 214
oFC01 ............................................................................ 214
oFC02 ............................................................................ 215
oFC03 to oFC11 ................................................................ 215
oFC12 to oFC17 ................................................................ 215
oFC50 to oFC55 ................................................................ 215
OFF button Input ............................................................... 233
OFF Key ...........................................................................79
OFF Key Function Selection .................................................. 305
oH ........................................................................... 215, 226
oH1 ............................................................................... 215
oH2 ............................................................................... 226
oH3 ......................................................................... 215, 226
oH4 ............................................................................... 216
oH Pre-Alarm Time Limit ..................................................... 142
oL1................................................................................ 216
oL2................................................................................ 217
oL3.......................................................................... 217, 227
oL4................................................................................ 217
oL5................................................................................ 217
oPE ............................................................................... 229
oPE01 ............................................................................ 229
oPE02 ............................................................................ 229
oPE03 ............................................................................ 229
oPE04 ............................................................................ 230
oPE05 ............................................................................ 230
oPE07 ............................................................................ 230
oPE08 ............................................................................ 230
oPE09 ............................................................................ 230
oPE10 ............................................................................ 231
oPE11 ............................................................................ 231
oPE16 ............................................................................ 231
oPE27 ............................................................................ 231
oPE28 ............................................................................ 231
oPE30 ............................................................................ 231
oPE Fault Parameter............................................................ 314
Operation Errors .......................................................... 201, 204
Operation Status Monitors..................................................... 175
Operator Related Settings...................................................... 163
oPr ................................................................................ 217
Option card connection error (CN5-A) ...................................... 213
Option Card Connection Error at Option Port CN5-A..................... 213
Option Card Connection Error at Option Port CN5-C..................... 214
Option card error occurred at option port CN5-A .......................... 213
Option card error occurred at option port CN5-B .......................... 214
Option card error occurred at option port CN5-C .......................... 215
Option Card External Fault.............................................. 207, 224
Option Card Fault at Option Port CN5-A ................................... 213
Option Card Fault at Option Port CN5-B.................................... 214
Option Card Fault at Option Port CN5-C.............................. 214, 215
Index
435