YASKAWA Z1000U Technical Manual page 426

H.3 User Setting Table
No.
C4-01
Torque Compensation Gain
C6-02 Carrier Frequency Selection
C7-60 Output Voltage Limit Mode Selection
d1-01
Frequency Reference 1
d1-02
Frequency Reference 2
d1-03
Frequency Reference 3
d1-04
Frequency Reference 4
d2-01 Frequency Reference Upper Limit
d2-02 Frequency Reference Lower Limit
d2-03 Master Speed Reference Lower Limit
d3-01 Jump Frequency 1
d3-02 Jump Frequency 2
d3-03 Jump Frequency 3
d3-04 Jump Frequency Width
E1-03 V/f Pattern Selection
E1-05 Maximum Voltage
E2-01 Motor Rated Current
E2-03 Motor No-Load Current
F6-01 Communications Error Operation Selection
External Fault from Communications Option
F6-02
Detection Selection
External Fault from Communications Option
F6-03
Operation Selection
Multi-Function Digital Input Terminal S3 Function
H1-03
Selection
Multi-Function Digital Input Terminal S4 Function
H1-04
Selection
Multi-Function Digital Input Terminal S5 Function
H1-05
Selection
Multi-Function Digital Input Terminal S6 Function
H1-06
Selection
Multi-Function Digital Input Terminal S7 Function
H1-07
Selection
Multi-Function Digital Input Terminal S8 Function
H1-08
Selection
H2-01 Multi-Function Contact Output (Terminal M1-M2)
Multi-Function Contact Output 2 (Terminal M3-
H2-02
M4)
Multi-Function Contact Output 3 (Terminal MD-
H2-03
ME-MF)
H3-01 Terminal A1 Signal Level Selection
H3-02 Terminal A1 Function Selection
H3-03
Terminal A1 Gain Setting
H3-04
Terminal A1 Bias Setting
H3-05 Terminal A3 Signal Level Selection
426
Name
Setting
User
No.
H3-06 Terminal A3 Function Selection
H3-07 Terminal A3 Gain Setting
H3-08
Terminal A3 Bias Setting
H3-09 Terminal A2 Signal Level Selection
H3-10 Terminal A2 Function Selection
H3-11
Terminal A2 Gain Setting
H3-12
Terminal A2 Bias Setting
H3-13 Analog Input Filter Time Constant
H3-14 Analog Input Terminal Enable Selection
H3-16 Terminal A1 Offset
H3-17 Terminal A2 Offset
H3-18 Terminal A3 Offset
Multi-Function Analog Output Terminal FM
H4-01
Monitor Selection
H4-02
Multi-Function Analog Output Terminal FM Gain
H4-03
Multi-Function Analog Output Terminal FM Bias
Multi-Function Analog Output Terminal AM
H4-04
Monitor Selection
H4-05
Multi-Function Analog Output Terminal AM Gain
H4-06
Multi-Function Analog Output Terminal AM Bias
Multi-Function Analog Output Terminal FM
H4-07
Signal Level Selection
Multi-Function Analog Output Terminal AM
H4-08
Signal Level Selection
L1-01 Motor Overload Protection Selection
L1-02 Motor Overload Protection Time
L2-01 Momentary Power Loss Operation Selection
L2-02 Momentary Power Loss Ride-Thru Time
L2-03 Momentary Power Loss Minimum Baseblock Time
L2-05 Undervoltage Detection Level (Uv1)
L3-02 Stall Prevention Level during Acceleration
L3-03 Stall Prevention Limit during Acceleration
L3-04 Stall Prevention Selection during Deceleration
L3-06 Stall Prevention Level during Run
L4-01 Speed Agreement Detection Level
L4-02 Speed Agreement Detection Width
L4-03 Speed Agreement Detection Level (+/-)
L4-04 Speed Agreement Detection Width (+/-)
L4-05 Frequency Reference Loss Detection Selection
L4-06 Frequency Reference at Reference Loss
L4-07 Speed Agreement Detection Selection
L5-01 Number of Auto Restart Attempts
L5-02 Auto Restart Fault Output Operation Selection
YASKAWA SIEP YAIZ1D 01C Z1000U HVAC MATRIX Drive Bypass Technical Manual
Name
Setting
User