YASKAWA Z1000U Technical Manual page 437

Reading BACnet Bypass Parameters ........................................ 346
Reading Drive MEMOBUS/Modbus Register Contents .................. 362
Real Time Clock ................................................................ 168
Reattaching the Front Cover ....................................................70
Reattaching the Terminal Cover ................................................67
Removing the Cooling Fan .................................................... 257
Removing the Front Cover ......................................................68
Removing the Terminal Cover..................................................67
Replacement Parts .............................................................. 251
RESET Key........................................................................79
Resistance Tuning Error ....................................................... 232
Response Messages from Drive to Master ............................ 359, 412
Restart Delay .................................................................... 186
Restart Enabled ................................................................. 141
Return Fan with PID Control Application.....................................91
Reverse Operation Selection .................................................. 102
Rotational Auto-Tuning for V/f Control.......................................94
RS-485 Interface ................................................................ 355
Run Active during Restart Delay ............................................. 221
Run Command/Frequency Reference Source Selection Error............ 230
Run Command Selection ................................................ 237, 238
RUN Command Selection for AUTO mode ................................ 281
Run Command Source Selection ............................................. 318
S
S: Special Parameters .......................................................... 167
S1: Dynamic Noise Control Function........................................ 307
S2: Sequence Timers ..................................................... 168, 307
SAFE ............................................................................. 227
Safety Circuit Fault ............................................................. 218
Safety Open Message Selection .............................................. 190
SCF ............................................................................... 218
S-Curve Characteristics .................................................. 121, 200
SE ................................................................................. 227
Selecting the Type of Auto-Tuning ............................................95
Sequence Timer 1............................................................... 168
Sequence Timer 1 Day Selection ............................................. 307
Sequence Timer 1 Reference Source......................................... 307
Sequence Timer 1 Selection................................................... 307
Sequence Timer 1 Start Time ................................................. 307
Sequence Timer 1 Stop Time ................................................. 307
Sequence Timer 2 Day Selection ............................................. 308
Sequence Timer 2 Reference Source......................................... 308
Sequence Timer 2 Selection................................................... 308
Sequence Timer 2 Start Time ................................................. 307
Sequence Timer 2 Stop Time ................................................. 308
Sequence Timer 3 Day Selection ............................................. 308
Sequence Timer 3 Reference Source......................................... 308
Sequence Timer 3 Selection................................................... 308
Sequence Timer 3 Start Time ................................................. 308
Sequence Timer 3 Stop Time ................................................. 308
Sequence Timer 4 Day Selection ............................................. 309
Sequence Timer 4 Reference Source......................................... 309
Sequence Timer 4 Selection................................................... 309
Sequence Timer 4 Start Time ................................................. 308
Sequence Timer 4 Stop Time ................................................. 308
Sequence Timer Error .......................................................... 231
Sequence Timers 1/2/3/4 Reference Source................................. 170
Sequence Timers 1/2/3/4 Selection........................................... 169
Sequence Timers 1 to 4 Day Selection....................................... 169
YASKAWA SIEP YAIZ1D 01C Z1000U HVAC MATRIX Drive Bypass Technical Manual
Sequence Timers 1 to 4 Start Time........................................... 169
Sequence Timers 1 to 4 Stop Time ........................................... 169
Sequence Timers 2 to 4 ........................................................ 168
SEr ................................................................................ 218
Serial Comm Alarm ............................................................ 221
Serial Communication Fault Detection Selection .......................... 406
Serial Communications Cable Connection Terminal (TB3) .. 334, 354, 403
Serial Communications Fault Time Select .................................. 406
Serial Communications Node Address Select .............................. 405
Serial Communications Protocol Select ..................................... 405
Serial Communications Receive to Transmit Wait Time.................. 406
Serial Communication Terminals...............................................66
Serial Communication Transmission Error ................................. 223
Setup Mode ........................................................................88
Shielded Twisted-Pair Cables ...................................................71
Simplified Setup Using the Quick Setting Group ............................88
Slave Address ................................................................... 360
Smoke Purge in Bypass ........................................................ 221
Smoke Purge in Drive.......................................................... 221
Snubber Discharge Resistor Overheat ....................................... 218
Soft Charge Bypass Relay Maintenance..................................... 317
Soft Charge Bypass Relay Maintenance Time.............................. 226
Soft Starter Speed Reference at Previous Fault............................. 315
Software No. (Flash) ........................................................... 314
Software No. (ROM) ........................................................... 314
Software version ..................................................................27
SoH ............................................................................... 218
Speed Agree 1 ................................................................... 136
Speed Agree 2 ................................................................... 139
Speed Agree Detection Level ................................................. 154
Speed Agree Detection Level (+/-) ........................................... 154
Speed Agree Detection Selection............................................. 155
Speed Agree Detection Width ................................................ 154
Speed Agree Detection Width (+/-) .......................................... 154
Speed Control Accuracy ....................................................... 273
Speed Control Range ........................................................... 273
Speed Search .................................................................... 101
Speed Search Deceleration Time ............................................. 105
Speed Search Delay Time ..................................................... 105
Speed Search Detection Compensation Gain ............................... 106
Speed Search Method Selection .............................................. 107
Speed Search Method Switching Level (Speed Estimation Type) ....... 106
Speed Search Restart Current Level.......................................... 107
Speed Search Restart Detection Time........................................ 107
Speed Search Selection at Start ............................................... 105
Speed Search Selection when Run Command is Given during Uv ...... 108
Speed Search Wait Time....................................................... 107
SrC ................................................................................ 218
Srr ................................................................................. 219
Stall Prevention ................................................................. 152
Stall Prevention Level during Acceleration ................................. 152
Stall Prevention Level during Run ........................................... 154
Stall Prevention Limit during Acceleration ................................. 153
Stall Prevention Selection during Acceleration............................. 301
Stall Prevention Selection during Deceleration............................. 153
Stall Prevention Selection during Run ....................................... 301
Standard .......................................................................... 273
Standard Connection Diagram ..................................................44
Starting Torque.................................................................. 273
Start Speed Search Select...................................................... 107
Index
437