YASKAWA P1000 Technical Manual page 407

SE ................................................................................. 210
Selecting the Type of Auto-Tuning ............................................77
Sequence Timer 1............................................................... 154
Sequence Timer 1 Day Selection ............................................. 271
Sequence Timer 1 Reference Source......................................... 271
Sequence Timer 1 Selection................................................... 271
Sequence Timer 1 Start Time ................................................. 271
Sequence Timer 1 Stop Time ................................................. 271
Sequence Timer 2 Day Selection ............................................. 272
Sequence Timer 2 Reference Source......................................... 272
Sequence Timer 2 Selection................................................... 272
Sequence Timer 2 Start Time ................................................. 272
Sequence Timer 2 Stop Time ................................................. 272
Sequence Timer 3 Day Selection ............................................. 272
Sequence Timer 3 Reference Source......................................... 272
Sequence Timer 3 Selection................................................... 272
Sequence Timer 3 Start Time ................................................. 272
Sequence Timer 3 Stop Time ................................................. 272
Sequence Timer 4 Day Selection ............................................. 273
Sequence Timer 4 Reference Source......................................... 273
Sequence Timer 4 Selection................................................... 273
Sequence Timer 4 Start Time ................................................. 272
Sequence Timer 4 Stop Time ................................................. 273
Sequence Timer Error .......................................................... 214
Sequence Timers 1/2/3/4 Reference Source................................. 156
Sequence Timers 1/2/3/4 Selection........................................... 156
Sequence Timers 1 to 4 Day Selection....................................... 155
Sequence Timers 1 to 4 Start Time........................................... 155
Sequence Timers 1 to 4 Stop Time ........................................... 155
Sequence Timers 2 to 4 ........................................................ 155
SEr ................................................................................ 202
Serial Comm Fault.............................................................. 205
Serial Communication Fault Detection Selection .......................... 380
Serial Communications Baud Rate Select ................................... 379
Serial Communications Cable Connection Terminal (TB3) .. 308, 328, 377
Serial Communications Fault Time Select .................................. 380
Serial Communications Node Address Select .............................. 379
Serial Communications Protocol Select ..................................... 379
Serial Communications Receive to Transmit Wait Time.................. 380
Serial Communication Terminals...............................................48
Serial Communication Transmission Error ................................. 206
Setup Mode ........................................................................68
Shielded Twisted-Pair Cables ...................................................51
Simplified Setup Using the Quick Setting Group ............................68
Slave Address ................................................................... 334
Smoke Purge in Bypass ........................................................ 205
Smoke Purge in Drive.......................................................... 205
Soft Charge Bypass Relay Maintenance..................................... 281
Soft Charge Bypass Relay Maintenance Time.............................. 208
Soft Starter Speed Reference at Previous Fault............................. 279
Software No. (Flash) ........................................................... 278
Software No. (ROM) ........................................................... 278
Software version ..................................................................29
Speed Agree 1 ................................................................... 118
Speed Agree 2 ................................................................... 121
Speed Control Range ........................................................... 243
Speed Estimation Type Speed Search..........................................87
Speed Search ......................................................................83
Speed Search Deactivation Current ............................................88
Speed Search Deceleration Time ...............................................89
YASKAWA SIEP YAIP1B 01B YASKAWA AC Drive – P1000 Bypass Technical Manual
Speed Search Delay Time .......................................................89
Speed Search Detection Compensation Gain .................................89
Speed Search Method Selection ................................................90
Speed Search Restart Current Level............................................90
Speed Search Restart Detection Time..........................................90
Speed Search Selection at Start .................................................88
Speed Search Wait Time.........................................................90
Stall Prevention ........................................................... 136, 186
Stall Prevention Level during Acceleration ........................... 136, 266
Stall Prevention Level during Run ..................................... 138, 267
Stall Prevention Limit during Acceleration ........................... 137, 266
Stall Prevention Selection during Deceleration....................... 137, 267
Starting Torque.................................................................. 243
Stationary Auto-Tuning..........................................................77
Stationary Auto-Tuning for Line-to-Line Resistance ........................76
Status Display .....................................................................70
STo ............................................................................... 202
Stopping Method after Communication Error .............................. 133
Stopping Method Selection......................................................83
Storage Temperature .............................................................38
Supported Properties of Objects .............................................. 314
Surrounding Area .................................................................38
Swing PWM ..................................................................... 104
T
T/L3.................................................................................43
T1-03 ...............................................................................78
T1-04 ...............................................................................78
T1-05 ...............................................................................78
T1-06 ...............................................................................78
T1-07 .......................................................................... 78, 79
TdE ............................................................................... 202
Terminal A1 Bias Setting...................................................... 125
Terminal A1 Function Selection.............................................. 125
Terminal A1 Gain Setting ..................................................... 125
Terminal A1 Signal Level Selection ......................................... 124
Terminal A2 Bias Setting...................................................... 128
Terminal A2 Function Selection.............................................. 127
Terminal A2 Gain Setting ..................................................... 128
Terminal A2 Signal Level Selection ......................................... 127
Terminal A3 Bias Setting...................................................... 127
Terminal A3 Function Selection.............................................. 127
Terminal A3 Gain Setting ..................................................... 127
Terminal A3 Signal Level Selection ......................................... 127
Terminal Board ...................................................................33
Terminal Board Connection Error............................................ 191
Terminal Board Connector ......................................................33
Test Run....................................................................... 76, 79
Through Mode .................................................................. 121
TIM ............................................................................... 202
Time Data Error................................................................. 202
Time Not Set .................................................................... 202
Time to Continue Making Fault Restarts .................................... 267
Too Many Speed Search Restarts............................................. 202
Torque Compensation Gain ............................................. 104, 186
Torque Compensation Primary Delay Time ................................ 186
Torque Detection ............................................................... 130
Torque Detection 1 ............................................................. 121
Torque Detection Level 1................................................ 144, 268
Torque Detection Selection 1 ........................................... 143, 268
Index
407