YASKAWA P1000 Technical Manual page 405

Momentary Power Loss Ride-Thru Time ............................. 136, 266
Monitor Parameters....................................................... 131, 275
Most Recent Fault .............................................................. 279
Motor 1 Parameters............................................................. 113
Motor Base Frequency ................................................ 78, 80, 273
Motor Base Speed ..........................................................80, 274
Motor Data Error................................................................ 215
Motor Does Not Rotate ........................................................ 220
Motor Hunting and Oscillation Control Parameters ....................... 186
Motor Iron Loss .............................................................80, 274
Motor is Too Hot ............................................................... 221
Motor No-Load Current........................................................ 113
Motor Overheat ................................................................. 209
Motor Overheat Alarm (PTC Input).......................................... 199
Motor Overheat Fault (PTC Input) ........................................... 199
Motor Overload ................................................................. 199
Motor Overload Estimate (oL1) .............................................. 281
Motor Overload Protection Selection .................................. 134, 266
Motor Overload Protection Time ....................................... 135, 266
Motor Performance Fine-Tuning ............................................. 186
Motor Poles........................................................................78
Motor Protection ................................................................ 134
Motor Pull Out or Step Out Detection ....................................... 202
Motor q-Axis Current at Previous Fault ..................................... 279
Motor Rated Current ............................................ 78, 80, 113, 273
Motor Rated Power .........................................................79, 273
Motor Rated Voltage .................................................. 78, 79, 273
Motor Rotates in One Direction Only........................................ 221
Motor Stalls during Acceleration or With Large Loads ................... 222
Motor Underload................................................................ 203
Motor Underload Protection Level at Minimum Frequency ........ 145, 268
Motor Underload Protection Selection................................. 145, 268
Motor Wiring......................................................................43
Multi-Function Analog Input Selection Error............................... 213
Multi-Function Analog Input Terminal Settings ........................... 125
Multi-Function Analog Outputs .............................................. 131
Multi-Function Analog Output Terminal AM Bias ........................ 131
Multi-Function Analog Output Terminal AM Gain........................ 131
Multi-Function Analog Output Terminal AM Monitor Selection........ 131
Multi-Function Analog Output Terminal AM Signal Level Selection .. 132
Multi-Function Analog Output Terminal FM Bias......................... 131
Multi-Function Analog Output Terminal FM Gain ........................ 131
Multi-Function Analog Output Terminal FM Monitor Selection ........ 131
Multi-Function Analog Output Terminal FM Signal Level Selection... 132
Multi-Function Digital Input Terminal Settings ............................ 115
Multi-Function Digital Outputs ............................................... 117
Multi-Function Input Selection Error ........................................ 212
Multiple Connection Diagram .......................................... 362, 378
Multi-Step Speed Selection.................................................... 106
N
n1-02.............................................................................. 186
N2 Configuration ............................................................... 376
N2 Serial Communication ..................................................... 379
N2 Setup Parameters ........................................................... 379
N2 Specifications ............................................................... 376
Network Digital Input Select.................................................. 179
Network Termination .............................................. 308, 329, 378
No-Load Current Alarm ....................................................... 215
No-Load Current Error......................................................... 216
YASKAWA SIEP YAIP1B 01B YASKAWA AC Drive – P1000 Bypass Technical Manual
Notes on Stationary Auto-Tuning ..............................................77
nSE ............................................................................... 197
Number of Auto Restart Attempts...................................... 140, 267
Number of Motor Poles ....................................................80, 273
Number of Run Commands ................................................... 280
Number of Speed Search Restarts ..............................................90
O
oC ................................................................................. 197
oFA00 ............................................................................ 198
OFF button Input ............................................................... 216
OFF Key ...........................................................................59
oH ........................................................................... 198, 209
oH1 ............................................................................... 199
oH2 ............................................................................... 209
oH3 ......................................................................... 199, 209
oH4 ............................................................................... 199
oH Pre-Alarm Time Limit ..................................................... 124
oL1................................................................................ 199
oL2................................................................................ 200
oL3.......................................................................... 200, 209
oL7................................................................................ 200
oPE ............................................................................... 212
oPE01 ............................................................................ 212
oPE02 ............................................................................ 212
oPE03 ............................................................................ 212
oPE05 ............................................................................ 213
oPE07 ............................................................................ 213
oPE09 ............................................................................ 213
oPE10 ............................................................................ 213
oPE11 ............................................................................ 213
oPE28 ............................................................................ 214
oPE Fault Parameter............................................................ 278
Operation Errors .......................................................... 187, 189
Operation Status Monitors..................................................... 160
Operator Related Settings...................................................... 150
oPr ................................................................................ 201
Option Card Connection Error at Option Port CN5........................ 198
Option card connector (CN5-A) ................................................33
Option card connector (CN5-B) ................................................33
Option card connector (CN5-C) ................................................33
Option Card External Fault.............................................. 192, 207
Option Communication Error ........................................... 190, 206
Option Frequency Reference .................................................. 281
Oscillation or Hunting.......................................................... 223
Output Current .................................................................. 277
Output Current 1 during Speed Search ........................................89
Output Current at Previous Fault ............................................. 278
Output Current Imbalance ..................................................... 197
Output Frequency............................................................... 277
Output Frequency after Soft Start ............................................ 278
Output Frequency at Previous Fault.......................................... 278
Output Frequency is not as High as Frequency Reference ................ 224
Output Frequency Resolution ................................................. 243
Output Ground Fault Detection Selection ............................. 146, 268
Output Phase Loss .............................................................. 197
Output Phase Loss Protection ................................................. 268
Output Phase Loss Protection Selection ..................................... 146
Output Power.................................................................... 277
Output Power at Previous Fault............................................... 278
Index
405