YASKAWA P1000 Quick Start Manual

P1000 AC Drive
Quick Start Procedure
Step
The following P1000 Model
1
procedure is a Identification and Mounting
supplement to
other To make sure you received the correct model, it is essential to
verify the P1000 nameplate with your order and make sure the
documentation
P1000 has the correct rating so it can be used with your motor.
Please check the nameplate information as shown in the
supplied with this
example below.
equipment and will
Drive Model
guide the user in
Number
CIMR-PU2A0021FAA
properly wiring the
Input Power CC : CIMR-PU2A0021FAA
Rating
P1000 and motor.
Output Power
Rating
It will also show
6W3050 - 2 - 100
Weight
the user how to
J0073D207410100
Serial
Number
configure the
UL File
P1000 for a Number
general purpose
application.
· Check that the available power will meet the
requirements.
output power
· Ensure that the
DANGER!
compatible with the motor requirements.
Improper wiring
· In the case of systems with more than one P1000, follow
can and will cause
the above procedure for each P1000 and motor.
bodily harm as well
Mounting the P1000
as damage to the
The mounting of the P1000 is extremely important regarding
equipment.
environment and accessibility. Depending on your system,
there are various models available and the mounting
dimensions (footprint) may be different. Because the
When installing the
mounting procedure is fairly extensive, it is beyond the scope
of this document; the user is referred to the P1000 Quick
system, be sure to
Start Guide (
Document No. TOEP YAIP1U 01
follow good wiring
P1000, Section 2.2, Mechanical Installation
that you received and follow the procedure described in the
practices and all
manual to ensure a safe and functional installation. In cases
applicable codes.
where the system has more than one P1000, refer to the
proper clearances required for adequate ventilation.
Ensure that the
pay particular attention to:
mounting of
· The clearances to be maintained around the enclosure
components is
for adequate ventilation.
secure and that the
· The environmental specifications such as avoiding
excessive dampness, extreme temperatures, chemical
environment, such
exposure, corrosive areas, etc. to avoid damage to the
as extreme
equipment and to maintain safety.
dampness, poor
Removing and Attaching the Terminal Cover
ventilation, etc. will
Improper removal of the P1000 terminal cover as well as front
not cause system
cover can cause extensive damage to the P1000. To avoid
damage to these items, please pay particular attention to the
degradation.
P1000 Quick Start Guide, Document No.
Section 3.5, Removing and Attaching the Terminal Cover
Please read this
cheat sheet and
other
documentation
provided with the
P1000 thoroughly
before attempting
NEMA 1
any installation.
Open Chassis
Step
Connect Motor and
2
Fig.1 & 2 below show the electrical connections for the
input power and motor terminals for various P1000 models.
Select the proper diagram for the model you are installing
(see Step 1). WITH POWER OFF make the appropriate
connections.
Make sure to follow good wiring practices and all applicable
Drive Spec Number
codes. Ensure that the equipment is grounded properly as
shown in fig. 1
Normal
Duty Amps
! DANGER; LETHAL VOLTAGES ARE PRESENT- Before
Software applying power to the P1000, ensure that the terminal cover
8500
Version
is fastened and all wiring connections are secure. After the
power has been turned OFF, wait at least five minutes until
the charge indicator extinguishes completely before touching
any wiring, circuit boards or components.
WARNING DO NOT CONNECT ANY OF THE
FOLLOWING TERMINALS TO EARTH GROUND
B1 B2
input power
from the P1000 is
DC Bus terminals
location varies by
(T/L3)
(S/L2)
(R/L1)
) received with the
. Match the model
Connect to chassis
Input
Protection
(Fuse or Circuit
Breaker)
Please
L1 L2 L3
Use L1, L2 for Use L1, L2, L3 for
*
1Ø Input Power 3Ø Input Power
Fig. 1 Input Power and Output Motor Electrical Connections for
Models: 2_0004 - 2_0056, 4_0002 - 4_0044 and 5_0003 - 50011
TOEP YAIP1U 01 ,
.
(R/L1) (S/L2)
(T/L3)
Input
Protection
(Fuse or Circuit
Breaker)
L1 L2 L3
Use L1, L2 for Use L1, L2, L3 for
1Ø Input Power *
3Ø Input Power
Fig. 2 Input Power and Output Motor Electrical Connections for
Models: 2_0110 & Larger and 4_0058 & Larger
*
Make sure the P1000 has been properly sized for single phase input
power. For best performance, the drive input supply voltage must be
equal to or greater than the motor rated voltage.
Step
Real-time
3
Line Power
Clock Setup
This step shows how to setup the
P1000 real-time clock for first
use.
Power up the drive and set the
real-time Clock. The real-time
Clock setup screen will appears
at first power up.
Note: after the real-time clock is
set this screen will not show
again unless parameter o4-17 is
set to "Set".
Real-time Clock Setup Screen
-
+1 +2 +3
model.
(W/T3)
(U/T1)
(V/T2)
To change
direction of
ground
motor rotation
swap any two
of the three
motor leads.
Press to select the digit
Connect
frame to
you would like to change and
ground
3Ø Induction
motor
use to adjust.
When date and time are set
NOT USED
press to save.
BUS TERMINALS:
DO NOT CONNECT TO GROUND
nd
Example: Jun 2 2012, 3:30pm
(W/T3)
(U/T1)
(V/T2)
To change direction of motor
rotation swap any two of the Note: Do NOT adjust sec per
three motor leads.
month.
Connect to
chassis
ground
IMPORTANT
If no key is pressed within 30
sec. the operator will revert
back to the main menu
Connect
frame to
showing a "TIM" alarm
ground
3Ø Induction
(Alarm not set).
motor
To set the real-time clock
again disconnect and
reconnect the operator.
Step
Selecting Start/Stop and Speed Method
4
This step shows how to setup the sequence and reference method of the P1000. The
sequence method determines how the P1000 drive receives its start and stop command
and the reference method determines how the speed of the motor is controlled. Make sure
all protective covers have been re-attached and power is turned on. . DO NOT RUN THE
MOTOR. This section may require you to change one or more P1000 parameters. Please
refer to Step 5 for a detailed explanation on how to change parameters.
SELECT SPEED METHOD
1.
Adjust motor speed / frequency from the Digital Operator
Go to parameter b1-01, set value to
To adjust frequency use / and press
2.
Adjust motor speed / frequency from external terminals (0 - 10V / 4 - 20mA Signal)
Go to parameter b1-01, set value to
Speed Potentiometer
+V AC A1 A2 A3 FM AM AC RP AC
24V
+V AC
Potentiometer
2K Ohm
0 ~ 10Vdc
0 – 20mA / 4- 20mA Connection
E(G)
+V AC A1 A2 A3 FM AM AC RP AC 24V +V AC
Cable
E(G)
Shield
+
4 ~ 20mA
Black: Output
A1 A3
4 – 20mA (2)
Jumper located
V
inside the drive on
the terminal board
Cable
I
(Factory Default) Type
A2
nd
Note: 2 row of terminal board is shown here.
SELECT START / STOP CONTROL METHOD
1.
Start / Stop Control from Digital Operator
Go to parameter b1-02, set value to
2.
Start / Stop Control from external terminals (switch or relay contact)
Go to parameter b1-02, set value to
User Terminals
S1 S2 S3 S4 S5 S6 S7 S8 SN SC SP
Forward Reverse Start
Link
Switch
Stop
Wiring Diagram: 2-Wire Control
Switch
Use for maintained contacts
rd
Note: 3 row of terminal board is shown here.
NOTE: It is beyond the scope of this document to program the P1000 drive for network communication control.
Please refer to the refer to the P1000 Technical Manual, (Document No.
Page 1 of 2
b1-01
.
(Factory Default)
0 – 10V Connection
A1 A2 A3 FM AM AC RP AC 24V
Cable E(G)
+
Shield
2-Wire, 4-20mA Transducer
A1 A2 A3 FM AM AC RP AC 24V
SN
Cable
Shield
Install link (AC-SN) when
using transducer.
Brown or Red: +Power (1)
DIN
Type
b1-02
( Factory Default)
User Terminals
S1 S2 S3 S4 S5 S6 S7 S8 SN SC SP
Reverse
Normally
Link
Open
Normally
Closed
Wiring Diagram: 3-Wire Control
Use for momentary contacts
(Set Parameter A1-03 to 3330)
for this selection.
SIEP YAIP1U 01)