Agilent Technologies 4396B Gpib Programming Manual page 8

4. Reading Measurement Data
To Read Data Using the Marker Search Function . . . . . . . . . . . . . . . .
Search Maximum Value . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Get Measurement Trace Using ASCII Format . . . . . . . . . . . . . . . .
Set the Receive Array . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Data Transfer Format . . . . . . . . . . . . . . . . . . . . . . . . .
Read Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Get Measurement Trace Using Binary Format . . . . . . . . . . . . . . . .
Set the Receive Array . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Data Transfer Format . . . . . . . . . . . . . . . . . . . . . . . . .
Read Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set the Receive Array . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Data Transfer Format . . . . . . . . . . . . . . . . . . . . . . . . .
Read Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Writing Data Arrays to the Analyzer
To Modify Calibration Data . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Calibration Data . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modify Calibration Data . . . . . . . . . . . . . . . . . . . . . . . . . .
Restore Modi ed Calibration Data . . . . . . . . . . . . . . . . . . . . . .
Redrawing Measurement Trace with Modi ed Calibration Data . . . . . . . .
To Modify Error-Corrected Data . . . . . . . . . . . . . . . . . . . . . . .
Read Error-Corrected Data . . . . . . . . . . . . . . . . . . . . . . . . .
Restore Modi ed Error-Corrected Data . . . . . . . . . . . . . . . . . . .
To Modify Trace Data . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Trace Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restore Modi ed Trace Data . . . . . . . . . . . . . . . . . . . . . . . .
6. Printing or Plotting the Analyzer's Display
To Print Analyzer Display . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Execute Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Observe Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. Controlling Instrument BASIC from Remote
To Control GPIB from Instrument BASIC . . . . . . . . . . . . . . . . . . .
To Execute an Instrument BASIC Command from the External Controller . . . .
To Run an Instrument BASIC Program From the External Controller . . . . . .
Open the Instrument BASIC Editor . . . . . . . . . . . . . . . . . . . . .
Send the Instrument BASIC Program . . . . . . . . . . . . . . . . . . . .
Close the Instrument BASIC Editor . . . . . . . . . . . . . . . . . . . . .
Run the Instrument BASIC Program . . . . . . . . . . . . . . . . . . . . .
To Transfer the Program to Instrument BASIC . . . . . . . . . . . . . . . . .
Open the Instrument BASIC Editor . . . . . . . . . . . . . . . . . . . . .
Transfer the Program . . . . . . . . . . . . . . . . . . . . . . . . . . .
Close the Instrument BASIC Editor . . . . . . . . . . . . . . . . . . . . .
To Load an Array in an Instrument BASIC Program to the External Controller . .
Transfer the Program Array of Instrument BASIC . . . . . . . . . . . . . .
Contents-2
4-2
4-2
4-3
4-4
4-4
4-5
4-5
4-6
4-7
4-7
4-8
4-9
4-10
4-10
5-1
5-2
5-3
5-3
5-5
5-6
5-7
5-7
5-8
5-9
5-9
6-1
6-1
6-1
6-1
7-1
7-3
7-4
7-4
7-4
7-4
7-5
7-5
7-5
7-6
7-6
7-6
7-6