Agilent Technologies 4396B Gpib Programming Manual page 10

Figures
1-1. System Con guration for GPIB Remote Control . . . . . . . . . . . . . . .
1-2. Program Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Sample Program : Basic Measurement (1/2) . . . . . . . . . . . . . . . . .
2-1. Trigger System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Sample Program : To Trigger Measurements Continuously . . . . . . . . . .
2-3. Sample Program : To Trigger a Measurement from Controller (1) . . . . . . .
2-4. Sample Program : To Trigger a Measurement from Controller (2) . . . . . . .
3-1. SRQ Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Sample Program: To Wait for the Preceding Operation to Complete . . . . . .
3-3. Sample Program : To Wait for Sweep End . . . . . . . . . . . . . . . . . .
3-4. Sweep-End Bit Enabling . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5. Sample Program : To Report Command Error Occurrence . . . . . . . . . .
3-6. Command-Error Bit Enabling . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Sample Program : To Read Data Using Marker Search Function . . . . . . . .
4-2. Sample Program : To Get Measurement Trace Using ASCII Format . . . . . .
4-3. Sample Program : To Get Measurement Trace Using IEEE 64-bit Floating Point
Format (For External Controller) (1/2) . . . . . . . . . . . . . . . . . .
4-4. FORM3 Data Transfer Format . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Sample Program : To Get Measurement Trace Using IEEE 64-bit Floating Point
Format (For Instrument BASIC) . . . . . . . . . . . . . . . . . . . . .
5-1. Sample Program : To Modify Calibration Data (1/2) . . . . . . . . . . . . .
5-2. Data Arrays, Data Processing, and GPIB Command . . . . . . . . . . . . . .
5-3. Sample Program : To Modify Error-Corrected Data . . . . . . . . . . . . . .
5-4. Sample Program : To Modify Trace Data . . . . . . . . . . . . . . . . . .
6-1. Sample Program : To Observe Printing . . . . . . . . . . . . . . . . . . .
7-1. Pass Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Sample Program: To Receive Control (On Instrument BASIC) . . . . . . . . .
7-3. Sample Program : To Run the Instrument BASIC Program From the External
Controller (On External Controller) . . . . . . . . . . . . . . . . . . .
7-4. Sample Program : To Transfer the Program to Instrument BASIC (on External
Controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5. Sample Program : To Load Instrument BASIC Program Array (on External
Controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Sample Program : Limit Test (1/2) . . . . . . . . . . . . . . . . . . . . . .
9-1. Sample Program : List Sweep (1/2) . . . . . . . . . . . . . . . . . . . . .
10-1. I/O Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-2. Sample Program : Synchronization of an External Handler with the Analyzer .
10-3. 8-Bit Data of OUT0-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-4. Sending Signal to an the External Handler . . . . . . . . . . . . . . . . . .
10-5. Reading Signal from the External Handler . . . . . . . . . . . . . . . . . .
11-1. Harmonic Distortion in a Signal . . . . . . . . . . . . . . . . . . . . . . .
11-2. Sample Program : Total Harmonic Distortion (THD) (1/2) . . . . . . . . . . .
11-3. Adjacent Channel Power . . . . . . . . . . . . . . . . . . . . . . . . . .
11-4. Sample Program : Adjacent Channel Power Calculation (1/2) . . . . . . . . .
11-5. 99 % Occupied Power Bandwidth . . . . . . . . . . . . . . . . . . . . . .
11-6. Sample Program : Occupied Power Bandwidth Calculation (1/2) . . . . . . .
Contents-4
1-2
1-5
1-5
2-1
2-2
2-3
2-4
3-1
3-2
3-3
3-3
3-5
3-6
4-2
4-4
4-6
4-8
4-9
5-1
5-5
5-6
5-8
6-2
7-1
7-2
7-4
7-5
7-6
8-1
9-1
10-1
10-2
10-2
10-2
10-3
11-1
11-2
11-4
11-4
11-6
11-7