NEC Aspila Topaz Programming Manual
NEC Aspila Topaz Programming Manual

NEC Aspila Topaz Programming Manual

Intelligent hybrid system
Hide thumbs Also See for Aspila Topaz:

Advertisement

Intelligent Hybrid System
Programming Manual
Issue : 1.0
Date : July, 2004

Advertisement

Table of Contents
loading

Summary of Contents for NEC Aspila Topaz

  • Page 1 Intelligent Hybrid System Programming Manual Issue : 1.0 Date : July, 2004...
  • Page 2 No representation is made that this manual is complete or accurate in all respects and NEC Infrontia Asia Pacific Sdn Bhd shall not be liable for any errors or omissions. In no event shall NEC Infrontia Asia Pacific Sdn Bhd be liable for any incidental or consequential damages in connection with the use of this manual.
  • Page 3: Table Of Contents

    Table of Contents Introduction to Programming ..............1 EFORE TART ROGRAMMING ● Program 10 : System Configuration Setup 10-01 ................13 IME AND   10-02 ................. 14 OCATION ETUP   10-03 PCB S ................. 15   ETUP 10-04 ..............18 USIC ON ETUP  ...
  • Page 4 Table of Contents ● Program 14 : Trunk Basic Setup 14-01 ............83   ASIC RUNK ETUP 14-02 ............ 87 NALOGUE RUNK ETUP   14-04 PBX S ..............89 EHIND ETUP   14-05 ................90   RUNK ROUPS 14-06 .............. 91 RUNK ROUP OUTING...
  • Page 5 Table of Contents ● Program 21 : Outgoing Call Setup 21-01 ........165   YSTEM PTIONS FOR UTGOING ALLS 21-02 ......... 167 RUNK ROUP OUTING FOR XTENSIONS   21-03 ........168 RUNK ROUP OUTING FOR RUNKS   21-04 ....... 169 ESTRICTION LASS FOR XTENSIONS...
  • Page 6 Table of Contents ● Program 25 : DID/DISA Setup 25-01 DID/DISA L ..........227   ASIC ETUP 25-02 DID/DISA T ..............228 ALKIE   25-03 DID/DISA T ....229 RANSFER ING WITH NCORRECT IALING   25-04 DID/DISA T ..230  ...
  • Page 7 Table of Contents ● Program 35 : SMDR and Account Code Setup 35-01 SMDR O ................ 281   PTIONS 35-02 SMDR O ............283 UTPUT PTIONS   35-03 SMDR P ......286 SSIGNMENT FOR RUNK ROUP   35-04 SMDR P ....
  • Page 8: Programming

    Table of Contents ● Program 90 : Maintenance Program 90-01 ................351   NSTALL 90-02 ........352 ETTING THE ROGRAMMING ASSWORD   90-03 ................354   90-04 ................355   90-05 ................. 356 ONTROL   90-06 ............... 357 RUNK ONTROL  ...
  • Page 9 Introduction to Programming Before You Start Programming Before Reading This Manual   This Manual provides you with detailed information about the system programs. By changing a program, you change the way the feature associated with that program works. In this section, you find out about each program, the features that the program affects and how to enter the program data into system memory.
  • Page 10 Introduction to Programming Before You Start Programming Location of Controls One of the following Display Key Telephone is required for the Programming. • 6TXD Key Telephone • 12TXD Key Telephone Handset Alphanumeric Display Indicator CHECK Key CLEAR Key Programmable Function Keys LND (Last Number Dial) Key OPAC (Operation Access) Key DC (Dial Control) Key...
  • Page 11 Introduction to Programming Before You Start Programming How to Enter the Programming Mode Depending on the mode of programming, the system may allow more than one person in the programming mode at one time. With telephone programming, two people can program simultaneously. Using the PC Program, only one person is allowed in programming.
  • Page 12 Introduction to Programming Before You Start Programming Using Keys to Move Around in the Programs Once you enter the programming mode, use the keys in the following chart to enter data, edit data and move around in the menus. Keys for Entering Data Use this Key…..
  • Page 13 Introduction to Programming Before You Start Programming Programming Names and Text Messages Several programs (e.g., Program 20-16: Selectable Display Messages) require you to enter text. Use the following chart when entering and editing text. When using the keypad digits, press the key once for the first character, twice for the second character, etc.
  • Page 14 Introduction to Programming Before You Start Programming System Capacities Maximum System Capacities Items Topaz System Class of Service Toll Restriction Classes Verifiable Account Code Table 2000 Day/Night Mode Numbers Day/Night Service Patterns Analogue Caller ID Detector 1) 924M with DSPDBU: 32 Dial Tone/Busy Tone Detector 2) 1) + 924ME: 64 DTMF Receiver...
  • Page 15 Introduction to Programming Before You Start Programming Maximum System Capacities Items Topaz Extension 924M(308M+308E+308E)/924ME(308ME+308E+308E) Extension Ports Telephone Extension Number Range 200-295 (default) Virtual Extension Ports Virtual Extension Port Numbers 01-50 Virtual Extension Port Number Range Undifined Class of Service Operator Access Number 0 or 9 Operator Extension DSS Console Number...
  • Page 16: Date

    Introduction to Programming Before You Start Programming Concept of 308M (Main Unit) The 308M(Main Unit) has Flash Memories and RAM. The System Software (Program) will be stored the Flash Memory area, and the customer data will be stored to the RAM. 1.
  • Page 17 Introduction to Programming Before You Start Programming 3. Re-Installation(COLD Start) This mode may be selected in case of re-installation from factory setting. The existing System Software(stored to the Flash Memory) will be remained, and the existing Customer data(stored to the RAM) will be cleared.
  • Page 18 Introduction to Programming Before You Start Programming 3. Concept of Slot Number Slot Number will be fixed as followings and EXIFU Slots has no slot number. 4. Concept of Trunk/Extension Port The system decides the regulation of software port calculation as below; - 308M/308ME Unit = Up to 3 Trunk Ports and 8 Extension Ports - 008E Unit = Up to 8 Extension Ports 5.
  • Page 19 Introduction to Programming Before You Start Programming - For Your Notes - Programming Manual...
  • Page 20 Introduction to Programming Before You Start Programming - For Your Notes - Programming Manual...
  • Page 21 Program 10: System Configuration Setup 10-01: Time and Date Description Use Program 10-01 : Time and Date to change the system Time and Date through system programming. Extension users can also dial Service Code 828 to change the Time if allowed by an extension’s Class of Service. Input Data Prog.
  • Page 22 Program 10: System Configuration Setup 10-02: Location Setup Description Use Program 10-02 : Location Setup to define the location of the installed system. Used for caller ID editing . Input Data Prog. No. Item Input data Default Description 10-02-01 Country Code Dial (up to 4 No setting Enter the country code...
  • Page 23 Program 10: System Configuration Setup 1530 10-03: PCB Setup Description Use Program 10-03 : PCB Setup to setup and confirm the Basic Configuration data for each PCB. When changing a defined terminal type, first set the type to ‘0’ and then plug the new device in to have the system automatically define it, alternatively redefine the type manually.
  • Page 24 Program 10: System Configuration Setup 10-03: PCB Setup For BRIU Unit ISDN Line Number Prog. No. Item Input data Default 10-03-01 ISDN Line Mode 0 : No setting 1 : T-Point 2 : S-Point 3 - 5 : Not Used 6 : S-Point(Leased Line) 10-03-02 Logical Port Number(see Note 1)
  • Page 25 Program 10: System Configuration Setup 10-03: PCB Setup Conditions None Feature Cross Reference None Telephone Programming Instructions To enter data for Program 10-03 (PCB Setup): 1. Enter the programming mode. 2. Enter 10 03 10-03-01SlotNo 3. Enter the number of the item you want to program. 10-03-xxSlotNoxx xxxxx 4.
  • Page 26: Setup

    Program 10: System Configuration Setup 10-04: Music on Hold Setup Description Use Program 10-04 : Music on Hold Setup to set the Music on Hold selection. For MOH, the system can provide silence to callers on Hold or one of two synthesized selections. Input Data Prog.
  • Page 27 Program 10: System Configuration Setup 10-05: Not Used Description This command is currently not used. Programming Manual...
  • Page 28 Program 10: System Configuration Setup 10-06: ISDN BRI Setup Description Use Program 10-06 : ISDN BRI Setup defines the TEI selection and DID mode for DID callers when the BRI feature is used. Previously, if the called party number did not match the SPID number, the system would not allow the call to go through.
  • Page 29: Record Circuits

    Program 10: System Configuration Setup 10-07: Conversation Record Circuits Description Use Program 10-07 : Conversation Record Circuits to select the number of Conference circuits to be used for Conversation Recording. Even if this program is set to ‘0’, the telephone conversation recording function can be used. Note: In this case, 16 circuits will be shared by conference recording and conversation recording.
  • Page 30 Program 10: System Configuration Setup 10-08: Pre-ringing Setup COPY Description Use Program 10-08 : Pre-Ringing Setup to enable or disable pre-ringing for trunk calls. This sets how a trunk initially rings a telephone. With pre-ringing, a burst of ringing occurs as soon as the trunk’s LED flashes. The call then continues ringing with the normal ring cadence cycle.
  • Page 31: Dial Tone Circuit Setup

    Program10: System Configuration Setup 10-09: DTMF and Dial Tone Circuit Setup COPY Description Use Program 10-09 : DTMF and Dial Tone Circuit Setup to allocate the circuits on the 308M PCBs for either DTMF receiving or dial tone detection. The 308M PCB has 16 circuits initially. With additional DSPDBU is installed in 924M Main Cabinet, the system can provide a total of 32 (16+16) circuits.
  • Page 32 Program 10: System Configuration Setup 10-12: Not Used Description This command is currently not used. Programming Manual...
  • Page 33 Program 10: System Configuration Setup 10-13: Not Used Description This command is currently not used. Programming Manual...
  • Page 34 Program 10: System Configuration Setup 10-14: Not Used Description This command is currently not used. Programming Manual...
  • Page 35 Program 10: System Configuration Setup 10-15: Not Used Description This command is currently not used. Programming Manual...
  • Page 36 Program 10: System Configuration Setup 10-16: Not Used Description This Command is currently not used. Programming Manual...
  • Page 37 Program 10: System Configuration Setup 10-17: Not Used Description This command is currently not used. Programming Manual...
  • Page 38 Program 10: System Configuration Setup 10-18: Not Used Description This command is currently not used. Programming Manual...
  • Page 39 Program 10: System Configuration Setup 10-19: Not Used Description This command is currently not used. Programming Manual...
  • Page 40 Program 10: System Configuration Setup 10-20: LAN Setup for External Equipment Description Use Program 10-20 : LAN Setup for External Equipment to define the TCP port/address/etc. for communicating to external equipment. Input Data 1 : CTI Server Type of External Equipment 5 : SMDR Output Prog.
  • Page 41: Ardware Setup

    Program 10: System Configuration Setup 10-21: EXIFU Hardware Setup Description Use Program 10-21 : EXIFU Hardware Setup to set up various hardware, such as the baud rate of COM port. Input Data Prog. No. Item Input Data Default Description 10-21-01 -Not Used- 10-21-02 Baud rate for...
  • Page 42 Program 10: System Configuration Setup 10-23: Not Used Description This command is currently not used. Programming Manual...
  • Page 43 Program 10: System Configuration Setup 10-24: Daylight Savings Setup Description Use Program 10-24 : Daylight Savings Setup to set the options for daylight savings. Input Data Default Related Prog. No. Item Input Data Program 10-24-01 Day light Savings Mode 0 : Off 1 : On 10-24-02 Time for Daylight Savings...
  • Page 44: Saving Setup

    Program 10: System Configuration Setup 10-24: Daylight Saving Setup Telephone Programming Instructions To enter data for Program 10-24 (Daylight Savings Setup): 1. Enter the programming mode. 2. Enter 10 24 10-24-01 Daylight Saving 3. Enter the number of the item you want to program. 10-24-xx xxxxx 4.
  • Page 45 Program 10: System Configuration Setup 10-25: Not Used Description This command is currently not used. Programming Manual...
  • Page 46 Program 10: System Configuration Setup 10-28: Not Used Description This command is currently not used. Programming Manual...
  • Page 47 Program 10: System Configuration Setup 10-29: Not Used Description This command is currently not used. Programming Manual...
  • Page 48 Program 10: System Configuration Setup 10-30: Not Used Description This command is currently not used. Programming Manual...
  • Page 49 Program 10: System Configuration Setup 10-33: Not Used Description This command is currently not used. Programming Manual...
  • Page 50 Program 10: System Configuration Setup For your Notes - Programming Manual...
  • Page 51: Umbering

    Program 11: System Numbering 11-01: System Numbering Description Use Program 11-01 : System Numbering to set the system’s internal (Intercom) numbering plan. The numbering plan assigns the first and second digits dialed and affects the digits an extension user must dial to access other extensions and features, such as service codes and trunk codes.
  • Page 52 Program 11: System Configuration Setup 11-01: System Numbering Step 3: Assign a function to the code selected After entering a code and specifying its length, you must assign its function. This is the Dial Type column in the System Numbering (page 52) table. The choices are: Dial Types Dial Type Description Related Program...
  • Page 53 Program 11: System Numbering 11-01: System Numbering Conditions None Feature Cross Reference Flexible System Numbering Telephone Programming Instructions To enter data for Program 11-01 (System Numbering): 1. Enter the programming mode. 2. Enter 11 01 11-01-01 Dial 1 Digit 3 3.
  • Page 54: Xtension Numbering

    Program 11: System Numbering 11-02: Extension Numbering Description Use Program 11-02 : Extension Numbering to set the extension number. The extension number can be up to four digits long. The first/second digit(s) of the number should be assigned in Program 11-01. This lets an employee move to a new location (port) and retain the same extension number.
  • Page 55 Program 11: System Numbering 11-02: Extension Numbering Telephone Programming Instructions To enter data for Program 11-02 (Extension Numbering): 1. Enter the programming mode. 2. Enter 11 02 11-02-01Ex Prt1 Extension No200 3. Enter the number of the item you want to program. 11-02-xxEx Prtxx xxxxx 4.
  • Page 56 Program 11: System Numbering 11-04: Virtual Extension Numbering Description Use Program 11-04 : Virtual Extension Numbering to define the virtual extension numbers. The extension number can be up to four digits long. The first/second digit(s) of the number should be assigned in Program 11-01. Input Data Virtual Extension Port Number 01-50...
  • Page 57 Program 11: System Numbering 11-06: ACI Extension Numbering Description Use Program 11-06 : ACI Extension Numbering to define the ACI extension numbers. The extension number can be up to four digits long. The first/second digit(s) of the number should be assigned in Program 11-01. ACI Port Number ACI Extension Description...
  • Page 58: Group Pilot Numbers

    Program 11: System Numbering 11-07: Department Group Pilot Numbers Description Use Program 11-07 : Department Group Pilot Numbers to assign pilot numbers to each Department Group set up in Program 16-02. The pilot number is the number users dial for Department Calling and Department Step Calling. The pilot number can be up to four digits long.
  • Page 59 Program 11: System Numbering 5122 11-08: ACI Group Pilot Number Description Use Program 11-08 : ACI Group Pilot Number to assign the pilot number to the ACI Groups set in Program 33- 02. The pilot number can be up to four digits long. The first/second digit(s) of the number should be assigned in Program 11-01 as type 2.
  • Page 60: Code

    Program 11: System Numbering 11-09: Trunk Access Code Description Use Program 11-09 : Trunk Access Code to assign the trunk access code (normally 9). The trunk access code can be set from 1 to 4 digits which is defined to type 3 and 4 in Program 11-01. This is the code extension users dial to access Automatic Route Selection.
  • Page 61 Program 11: System Numbering 11-09: Trunk Access Code Telephone Programming Instructions To enter data for Program 11-09 (Trunk Access Code): 1. Enter the programming mode. 2. Enter 11 09 11-09-01 Trunk Acs CD 0 3. Enter the number of the item you want to program. 11-09-xx xxxxx 4.
  • Page 62: Service Code Setup

    Program 11: System Numbering 11-10: Service Code Setup (for System Administrator) Description Use Program 11-10 : Service Code Setup (for System Administrator) to customize the Service Codes for the System Administrator. You can customize additional Service Codes in Programs 11-11, 11-12, 11-15, and 11-16. The following chart shows: •...
  • Page 63 Program 11: System Numbering 11-10: Service Code Setup (for Administrator) Feature Cross Reference  Refer to chart above. Telephone Programming Instructions To enter data for Program 11-10 (Service Code Setup): 1. Enter the programming mode. 2. Enter 11 10 11-10-01 NT-Mod SW 818 3.
  • Page 64 Program 11: System Numbering 11-11: Service Code Setup (for Setup/Entry) Description Use Program 11-11 : Service Code Setup (for Setup/Entry Operation) to customize the Service Codes which are used for registration and setup. You can customize additional Service Codes in Programs 11-10, 11-12, 11-15 and 11-16.
  • Page 65 Program 11: System Numbering 11-11: Service Code Setup (for Setup/Entry) Input Data (Cont’d) Related Prog. No. Item Terminals Default Program 20-11-17 11-11-28 Delayed Transfer for Every Extension Group KTS,SLT 24-05 24-02-08 11-11-29 Delayed Transfer Cancellation for Each Extension Group KTS,SLT 20-11-17 11-11-30 DND Setup for Each Extension Group...
  • Page 66 Program 11: System Numbering 11-12: Service Code Setup (for Service Access) Description Use Program 11-12 : Service Code Setup (for Service Access) to customize the Service Codes which are used for service access. You can customize additional Service Codes in Programs 11-10, 11-11, 11-15 and 11-16. The following chart shows: •...
  • Page 67 Program11: System Numbering 11-12: Service Code Setup (for Service Access) Input Data (Cont’d) Related Prog. No. Item Terminals Default Program 11-12-32 Answer for Park KTS,SLT 24-03 11-12-33 Group Hold KTS,SLT 11-12-34 Answer for Group Hold KTS,SLT 11-12-35 Extension Park Hold KTS,SLT 11-12-36 Doorphone Access...
  • Page 68 Program 11: System Numbering 11-12: Service Code Setup (for Service Access) Telephone Programming Instructions To enter data for Program 11-12 (Service Code Setup(for Service Access)): 1. Enter the programming mode. 2. Enter 11 12 11-12-01 Bypass Call 807 3. Enter the number of the item you want to program. 11-12-xx xxxxx 4.
  • Page 69 Program 11: System Numbering 11-15: Service Code Setup (for Special Access) Description Use Program 11-15 : Service Code Setup, Administrative (for Special Access) to customize the special access Service Codes which are used by the administrator. You can customize additional Service Codes in Programs 11-10 through 11-12 and 11-16.
  • Page 70 Program 11: System Numbering 11-15: Service Code Setup (for Special Access) Telephone Programming Instructions To enter data for Program 11-15 (Service Code Setup (for Special Access)): 1. Enter the programming mode. 2. Enter 11 15 11-15-01 Remote Maint 830 3. Enter the number of the item you want to program. 11-15-xx xxxxx 4.
  • Page 71 Program 11: System Numbering 11-16: One-Digit Service Code Setup Description Use Program 11-16 : One-Digit Service Code Setup to customize the one-digit Service Codes used when a busy or ring back signal is heard. You can customize additional Service Codes in Programs 11-10 through 11-15. The following chart shows: •...
  • Page 72 Program 11: System Numbering 11-16: One-Digit Service Code Setup Telephone Programming Instructions To enter data for Program 11-16 (One-Digit Service Code Setup): 1. Enter the programming mode. 2. Enter 11 16 11-16-01 Step Call 3. Enter the number of the item you want to program. 11-16-xx xxxxx 4.
  • Page 73: Ode Function Setup

    Program 12: Night Mode Setup 12-01: Night Mode Function Setup Description Use Program 12-01 : Night Mode Function Setup to set up the Night Mode options. Refer to the following chart for a description of each option, its range and default setting. Input Data Prog.
  • Page 74 Program 12: Night Mode Setup 12-02: Automatic Night Service Patterns Description Use Program 12-02 : Automatic Night Service Patterns to define the daily pattern of the auto night switch setting. Each Night Mode Group has 10 patterns. These patterns are used in Programs 12-03 and 12-04. The daily pattern consists of 20 timer settings.
  • Page 75 Program 12: Night Mode Setup 6712 12-02: Automatic Night Service Patterns Default All groups, all patterns:00:00 to 00:00 = Mode 1 All Night Group are as follows; Time Pattern 1 Set Time Number Start Time End Time Mode 0000 0800 0800 1700 1700...
  • Page 76 Program 12: Night Mode Setup 12-02: Automatic Night Service Patterns Telephone Programming Instructions To enter data for Program 12-02 (Automatic Night Service Patterns): 1. Enter the programming mode. 2. Enter 12 02 12-02- 01ModeGrp1 3. Enter the number of the item you want to program. 12-02- xxModeGrpx 4.
  • Page 77 Program 12: Night Mode Setup 6912 12-03: Weekly Night Service Switching Description Use Program 12-03 : Weekly Night Service Switching to define a weekly schedule of night-switch settings. Input Data Night Mode Service Group Number Day of the Week Time Schedule Pattern Number 01 = Sunday 01-10 02 = Monday...
  • Page 78 Program 12: Night Mode Setup 12-03: Weekly Night Service Switching Telephone Programming Instructions To enter data for Program 12-03 (Weekly Night Service Switching): 1. Enter the programming mode. 2. Enter 12 03 12-03- 01ModeGrp1 3. Enter the number of the item you want to program. 12-03- xxModeGrpx 4.
  • Page 79 Program 12: Night Mode Setup 12-04: Holiday Night Service Switching Description Use Program 12-04 : Holiday Night Service Switching to define a yearly schedule of holiday night-switch settings. This schedule is used for setting of special days which the company is expected to be closed, such as national holiday.
  • Page 80 Program 12: Night Mode Setup 12-05: Night Mode Group Assignment for Extensions Description Use Program 12-05 : Night Mode Group Assignment for Extensions to a assign Day/Night Mode Group for each extension. Input Data Extension Number Max.4 digits Night Mode Service Group Number Default Default No setting...
  • Page 81 Program 12: Night Mode Setup 12-06 : Night Mode Group Assignment for Trunks Description Use Program 12-06 : Night Mode Group Assignment for Trunks to assign a Day/Night Mode Group for each trunk port. Input Data Trunk Port Number 1-51 Night Mode Service Group Number Default Default...
  • Page 82 Program 12: Night Mode Setup 12-07: Text Data for Night Mode Description Use Program 12-07 : Text Data for Night Mode to make an original text message which is displayed on an LCD of key telephone in each Night Mode. Input Data Night Mode Service Group Number Day/ Night Mode...
  • Page 83 Program 12: Night Mode Setup 12-07: Text Data for Night Mode Telephone Programming Instructions To enter data for Program 12-07(Text Data for Night Mode): 1. Enter the programming mode. 2. Enter 12 07 12-07-01ModeGrp1 M1 - 3. Enter the number of the item you want to program. 12-07- xxModeGrpx 4.
  • Page 84 Program 12: Night Mode Setup For your Notes - Programming Manual...
  • Page 85 Program 13: Abbreviated Dialing 13-01: Abbreviated Dialing Function Setup Description Use Program 13-01 : Abbreviated Dialing Function Setup to define the Abbreviated Dialing functions. Input Data Prog. No. Item Input data Default Related Program 13-01-01 Abbreviated Dialing Auto 0 : Trunk outgoing mode 13-05 Outgoing Call Mode 1 : Extension outgoing mode...
  • Page 86 Program 13: Abbreviated Dialing 13-02: Group Abbreviated Dialing Bins Description Use Program 13-02 : Group Abbreviated Dialing Bins to define the range of bin numbers to be used by each Abbreviated Dialing group (refer to Program 13-03). Input Data Abbreviated Dialing Group Number Start Address of Abbreviated End Address of Abbreviated Dialing Bin...
  • Page 87: Group

    Program 13: Abbreviated Dialing 13-03: Abbreviated Dialing Group Assignment for Extensions Description Use Program 13-03 : Abbreviated Dialing Group Assignment for Extensions to assign Abbreviated Dialing Group for each extension. Input Data Extension Number Up to 4 digits Group Number Default Value 1-32 Default...
  • Page 88 Program 13: Abbreviated Dialing 13-04: Abbreviated Dialing Number and Name Description Use Program 13-04 : Abbreviated Dialing Number and Name to store Abbreviated Dialing data into the Abbreviated Dialing areas. This program is also used to define the names assigned to the Abbreviated Dialing numbers.
  • Page 89: Group

    Program 13: Abbreviated Dialing 13-05: Abbreviated Dialing Trunk Group Description Use Program 13-05 : Abbreviated Dialing Trunk Group to define the trunk group to be seized for each Abbreviated Dialing number (refer to Program 13-05). If this program has an entry of ‘0’ (no setting), then seizing a line follows the trunk access group routing of the caller’s extension (refer to Program 14-06).
  • Page 90 Program 13: Abbreviated Dialing 13-06: Station Abbreviated Dialing Number and Name Description Use Program 13-06 : Station Abbreviated Dialing Number and Name to store Abbreviated Dialing data into the Station Abbreviated Dialing areas. This program is also used to define the names assigned to the Station Abbreviated Dialing numbers.
  • Page 91 Program 14: Trunk Basic Setup 14-01: Basic Trunk Data Setup COPY Description Use Program 14-01 : Basic Trunk Data Setup to set the basic options for each trunk port. Refer to the chart below for a description of each option, its range and default setting. Input Data Trunk Port Number 1-51...
  • Page 92 Program 14: Trunk Basic Setup 14-01: Basic Trunk Data COPY Input Data(Cont’d) Prog. No. Item Input data Default Related Program 14-01-08 Toll Restriction 0 : Restriction Disable 21-04 Use this option to enable/disabled 1 : Restriction Enable 21-05 Toll Restriction for the trunk. If 21-06 enabled, the trunk follows Toll Restriction programming...
  • Page 93 Program 14: Trunk Basic Setup 14-01: Basic Trunk Data Setup COPY Input Data(Cont’d) Prog. No. Item Input data Default Related Program 14-01-18 Warning Beep Tone Signaling 0 : Disable 1 : Enable 14-01-19 Privacy Mode Toggle Option 0 : Disable Use this option to enable or disable 1 : Enable a trunk’s ability to be switched...
  • Page 94 Program 14: Trunk Basic Setup 14-01: Basic Trunk Data COPY Telephone Programming Instructions To enter data for Program 14-01(Basic Trunk Data Setup): 1. Enter the programming mode. 2. Enter 14 01 14-01-01 Trunk1 Name-Line 3. Enter the number of the item you want to program. 14-01-xx Trunkxx xxxxx 4.
  • Page 95 Program 14: Trunk Basic Setup 14-02: Analogue Trunk Data Setup COPY Description Use Program 14-02 : Analogue Trunk Data Setup to set the basic options for each analogue trunk port. Refer to the chart below for a description of each option, its range and default setting. Input Data Trunk Port Number 1-51...
  • Page 96 Program 14: Trunk Basic Setup 14-02: Analogue Trunk Data Setup COPY Input Data(Cont’d) Prog. No. Item Input data Default Related Program 14-02-09 Busy Tone Detection 0 : Disable 1 : Enable 14-02-10 Caller-ID 0 : Disable Enable or Disable a trunk’s ability to receive 1 : Enable Caller ID information 14-02-11...
  • Page 97 Program 14: Trunk Basic Setup 14-04: Behind PBX Setup COPY Description Use Program 14-04 : Behind PBX Setup to indicate if the trunk is installed behind a PBX. There is one item for each of the Night Service Modes: Input Data Trunk Port Number 1-51 Day/ Night Mode...
  • Page 98 Program 14: Trunk Basic Setup 14-05: Trunk Groups Description Use Program 14-05 : Trunk Groups to assign trunks to Trunk Groups. You can also assign the outbound priority for trunks within the group. When users dial up the trunk group, they seize the trunks in the order you specify in the outbound priority entry.
  • Page 99 Program 14: Trunk Basic Setup 14-06: Trunk Group Routing Description Use Program 14-06 : Trunk Group Routing to set up an outbound routing table for the trunk groups you assigned in Program 14-05. When users dial 9, the system routes their calls in the order (priority) you specify. For example, if a user dials 9 and all calls in the first group are busy, the system may route the call to another group.
  • Page 100 Program 14: Trunk Basic Setup 14-06: Trunk Group Routing Telephone Programming Instructions To enter data for Program 14-06(Trunk Group Routing): 1. Enter the programming mode. 2. Enter 14 06 14-06-01 R-TBL1 Order1 Data1 3. Enter the number of the item you want to program. 14-06-xx R-TBLxx xxxxx 4.
  • Page 101 Program 14: Trunk Basic Setup 14-07: Trunk Access Map Setup Description Use Program 14-07 : Trunk Access Map Setup to set up the Trunk Access Maps. This sets an extension’s access options for trunks. For example, an extension can only place outgoing calls on trunks to which it has outgoing access.
  • Page 102 Program 14: Trunk Basic Setup 14-07: Trunk Access Map Setup Telephone Programming Instructions To enter data for Program 14-07(Trunk Access Map Setup): 1. Enter the programming mode. 2. Enter 14 07 14-07-01Acs.Map1 TRK01 = 3. Enter the number of the item you want to program. 14-07-xxAcs.Mapx xxxxx 4.
  • Page 103 Program 14: Trunk Basic Setup 14-08: Music on Hold Source for Trunks COPY Description Use Program 14-08 : Music on Hold Source for Trunks to define a trunk’s Music on Hold source as either the ACI or BGM port. If ACI is selected as the source in Item 1, the port number for the source must be selected in Item 2. Note: Input Data Trunk Port Number...
  • Page 104 Program 14: Trunk Basic Setup 14-09: Conversation Recording Destination for Trunks COPY Description Use Program 14-09 : Conversation Recording Destination for Trunks to set the Conversation Recording destination for each trunk. If both Programs 14-09 and 15-12 define a destination, the destination in Program 15-12 will be followed. Note: Input Data Trunk Port Number...
  • Page 105 Program 15: Extension Basic Setup 15-01: Basic Extension Data Setup COPY Description Use Program 15-01 : Basic Extension Data Setup to define the basic settings for each extension. Input Data Extension Number Max 4 digits Prog. No. Item Input data Default Related Program...
  • Page 106 Program 15: Extension Basic Setup 15-01: Basic Extension Data Setup COPY Telephone Programming Instructions To enter data for Program 15-01(Basic Extension Data Setup): 1. Enter the programming mode. 2. Enter 15 01 15-01-01 TEL   ExtName-EXT 200 3. Enter the number of the item you want to program. 15-01-xx TELxxxx xxxxx 4.
  • Page 107 Program 15: Extension Basic Setup 15-02: Multi-Line Telephone Basic Data Setup COPY Description Use Program 15-02 : Multi-Line Telephone Basic Data Setup to set up various keyset options. Input Data Extension Number Max. 4 digits Prog. No. Item Input data Default Related Program...
  • Page 108 Program 15: Extension Basic Setup 15-02: Multi-Line Telephone Basic Data Setup COPY Input Data(Cont’d) Prog. No. Item Input data Default Related Program 15-02-11 Callback Automatic Answer 0 : Off Use this option to enable or disable 1 : On automatic answer for Callback. If enabled, extension automatically Answers Callback ringing when user lifts the Handset.
  • Page 109 Program 15: Extension Basic Setup 15-02: Multi-Line Telephone Basic Data Setup COPY Conditions None Feature Cross Reference Refer to feature in above chart. Telephone Programming Instructions To enter data for Program 15-02(Multi-Line Telephone Basic Data Setup): 1. Enter the programming mode. 2.
  • Page 110 Program 15: Extension Basic Setup 15-03: Single Line Telephone Basic Data Setup COPY Description Use Program 15-03 : Single Line Telephone Basic Data Setup to set up various Single Line Telephone options. Input Data Extension Number Max.4 digits Prog. No. Item Input data Default...
  • Page 111 Program15: Extension Basic Setup 15-03: Single Line Telephone Basic Data Setup COPY -External Line Reverse & Internal Line Reverse- Normal Idle Off-Hook Outgoing Call Idle Reverse Calling/Ringing Normal Answer Idle Incoming Call Reverse Detect Hang Up On-Hook Normal Idle Call Pickup Reverse Conditions None...
  • Page 112 Program 15: Extension Basic Setup 15-05: Not Used Description This command is currently Not used. Programming Manual...
  • Page 113 Program15: Extension Basic Setup 15-06: Trunk Access Map for Extensions COPY Description Use Program 15-06 : Trunk Access Map for Extensions to define the trunk access map for each extension. An extension can only place outgoing calls on trunks to which it has outgoing access. Use Program 14-07 to define the available 51 access maps.
  • Page 114 Program 15: Extension Basic Setup 15-07: Programming Function Keys COPY Description Use Program 15-07 : Programmable Function Keys to set the functions of an extension’s Programmable Function Key. For certain functions, you can append data to the key’s basic function. For example, the function 26 appended by data 1 makes a Group Call Pickup key for Pickup Group 1.
  • Page 115 Program 15: Extension Basic Setup 15-07: Programmable Function Keys COPY 1. Function Number List Function Function Additional Data LED Indication Number Not defined DSS/One-Touch Extension number or any Red On: Extension Busy numbers(Max. 36 digits) Off : Extension Idle Rapid Blink(Red): Call Forward Setup...
  • Page 116 Program 15: Extension Basic Setup 15-07: Programmable Function Keys COPY Input Data(Cont’d) Function Additional Data LED Indication Function Number None Call Pickup for Own Group Call Pickup for Another None Group Call Pickup for Specified Call Pickup Group None Group Number 01-32 Abbreviated Dial- Abbreviated dial No.
  • Page 117 Program 15: Extension Basic Setup 15-07: Programmable Function Keys COPY Input Data(Cont’d) Function Additional Data LED Indication Function Number -Not Used- Incoming Call Queuing Incoming Ring Group Red On : Under setting Message Setup No.1-25 Queuing Message Starting Red On : Active External Call Forward by Red On : Active Doorphone Box...
  • Page 118 Program 15: Extension Basic Setup 15-07: Programmable Function Keys COPY Input Data(Cont’d) Function Additional Data LED Indication Function Number Change Attendant Extension Number or None Message(DSPDBU) Pilot Number (Max.4 digits) -Not Used- -Not Used- -Not Used- -Not Used- Toll Restriction in Credit Extension Number (Max.4 digits) -Not Used-...
  • Page 119 Program 15: Extension Basic Setup 15-07: Programmable Function Keys COPY Telephone Programming Instructions To enter data for Program 15-07(Programmable Function Keys): 1. Enter the programming mode. 2. Enter 15 07 15-07-01 TEL200   KY01 = 3. Enter the number of the item you want to program. 15-07-xx TELxxxx xxxxx 4.
  • Page 120 Program 15: Extension Basic Setup 15-08: Incoming Virtual Extension Ring Tone Setup COPY Description Use Program 15-08 : Incoming Virtual Extension Ring Tone Setup to assign a ring tone range (0-4) to incoming virtual extensions assigned to a Virtual Extension key (Program 15-07). If you enable ringing for the key in Program 15-09, the key rings with the tone you set in this program.
  • Page 121 Program 15: Extension Basic Setup 15-08: Incoming Virtual Extension Ring Tone Setup COPY Telephone Programming Instructions To enter data for Program 15-08(Incoming Virtual Extension Ring Tone Setup): 1. Enter the programming mode. 2. Enter 15 08 15-08-01 TEL200   ICM Tone Pttrn 0 3.
  • Page 122 Program 15: Extension Basic Setup 15-09: Virtual Extension Ring Tone Assignment COPY Description Use Program 15-09 : Virtual Extension Ring Assignment to assign the ringing options for an extension’s Virtual Extension Key or Virtual Extension Group Answer Key which is defined in Program 15-07. You make an assignment for each Night Service Mode.
  • Page 123 Program 15: Extension Basic Setup 15-10: Incoming Virtual Extension Ring Tone Order Setup COPY Description Use Program 15-10 : Incoming Virtual Extension Ring Tone Order Setup to set the priority (1-4) for the Virtual Extension Ring Tones set in Program 15-08. When Virtual Extension calls ring an extension simultaneously, the tone with the highest order number (e.g., 1) rings.
  • Page 124 Program 15: Extension Basic Setup 15-11: Virtual Extension Delayed Ring Assignment COPY Description Use Program 15-11 : Virtual Extension Delayed Ring Assignment to assign the delayed ringing options for an extension’s Virtual Extension or Virtual Extension Group Answer keys (defined in Program 15-09). You make an assignment for each Night Service Mode.
  • Page 125 Program 15: Extension Basic Setup 15-12: Conversation recording Destination for Extensions COPY Description Use Program 15-12 : Conversation Recording Destination for Extensions to set the Conversation Recording destination for each extension. If both Programs 14-09 and 15-12 define a destination, the destination in Program 15-12 will be followed. Note: Input Data Extension Number...
  • Page 126 Program 15: Extension Basic Setup 15-12: Conversation Recording Destination for Extensions COPY Telephone Programming Instructions To enter data for Program 15-12(Conversation recording Destination for Extensions): 1. Enter the programming mode. 2. Enter 15 12 15-12-01 TEL200   Dest.Ext No 3. Enter the number of the item you want to program. 15-12-xx TELxxxx xxxxx 4.
  • Page 127 Program15: Extension Basic Setup 15-13: Loop Keys COPY Description Use Program 15-13 : Loop Keys to assign the Loop Key data for each keyset telephone. Loop Keys can be incoming, outgoing or both ways. Outgoing Loop Keys use the Data 1 options. Incoming Loop Keys use the Data 2 option.
  • Page 128 Program 15: Extension Basic Setup 15-13: Loop Keys COPY Telephone Programming Instructions To enter data for Program 15-13(Loop Keys): 1. Enter the programming mode. 2. Enter 15 13 15-13-01 TEL200   OTG KY01 = 3. Enter the number of the item you want to program. 15-13-xx TELxxxx xxxxx 4.
  • Page 129 Program 16: Department Group Setup 16-01: Extension (Department) Group Basic Data Setup COPY Description Use Program 16-01 : Department Group Basic Data Setup to set the function mode for each department group. Input Data Extension(Department) Group Number 1-32 Related Prog. No. Item Input data Default...
  • Page 130 Program 16: Department Group Setup 16-01: Extension (Department) Group Basic Data Setup COPY Conditions None Feature Cross Reference Department Calling Telephone Programming Instructions To enter data for Program 16-01(Extension(Department) Group Basic Data Setup): 1. Enter the programming mode. 2. Enter 16 01 16-01-01TEL Gr1  ...
  • Page 131 Program 16: Department Group Setup 16-02: Department Group Assignment for Extensions Description Use Program 16-02 : Department Group Assignment for Extensions to set the Department Groups. The system uses these groups for Department Calling. Assign pilot numbers to Department Groups you set up in Program 16-01. This lets system users place calls to the departments.
  • Page 132 Program 16: Department Group Setup 16-03: Secondary Department Group Description Use Program 16-03 : Secondary Department Group to set a second Department Group for extensions. Up to 16 extensions can be assigned per a Department Group. Input Data Extension(Department) Group Number 1-32 Secondary Extension...
  • Page 133 Program 20: System Option Setup 20-01: System Options Description Use Program 20-01 : System Options to set various system options. Input Data Related Prog. No. Item Input data Default Description Program 20-01-01 Operator Access 0 : Step Use this program to set up priority 20-17 Mode 1 : Circular...
  • Page 134 Program 20: System Option Setup 20-01: System Options Telephone Programming Instructions To enter data for Program 20-01(System Options): 1. Enter the programming mode. 2. Enter 20 01 20-01-01   Operator Access 0 3. Enter the number of the item you want to program. 20-01-xx xxxxx 4.
  • Page 135 Program 20: System Option Setup 20-02: System Options for Key Telephones Description Use Program 20-02 : System Options for Multi-Line Telephones to set various system options for Key Telephones. Input Data Prog. No. Item Input Data Default 20-02-01 Trunk Loop Key Operation Mode 0 : Indicate the Using Loop Trunk 1 : Not Indicated Mode...
  • Page 136 Program 20: System Option Setup 20-02: System Options for Key telephones Input Data(Cont’d) Prog. No. Item Input Data Default 20-02-09 Disconnect Supervision 0 : Disable Use this option to enable or disable 1 : Enable disconnect supervision for the system trunks.
  • Page 137 Program 20: System Option Setup 20-03: System Options for Single Line Telephones Description Use Program 20-03 : System Options for Single Line Telephones to set up various options for Single Line Telephones. Input Data Related Prog. No. Item Input Data Description Default Program...
  • Page 138 Program 20: System Option Setup 20-03: System Options for Single Line Telephones Feature Cross Reference Single Line Telephone, Analogue Telephone Programming Instructions To enter data for Program 20-03(System Options for Single Line Telephones): 1. Enter the programming mode. 2. Enter 20 03 20-03-01  ...
  • Page 139 Program 20: System Option Setup 20-04: System Options for Virtual Extensions Description Use Program 20-04 : System Options for Virtual Extensions to set up various system options for Virtual Extensions. Input Data Related Prog. No. Item Input Data Default Program 20-04-01 The virtual extension operation mode 0 : Release virtual extension after...
  • Page 140 Program 20: System Option Setup 20-05: Not Used Description This command is currently not used. Programming Manual...
  • Page 141 Program 20: System Option Setup 20-06: Class of Service for Extensions COPY Description Use Program 20-06 : Class of Service for Extensions to assign a Class of Service to an extension. There are15 Classes of Service that can be assigned. To specify the options in each Class of Service, refer to Programs 20-07 through 20-13.
  • Page 142 Program 20: System Option Setup 20-07: Class of Service Options (Administrator Level) Description Use Program 20-07 : Class of Service Options (Administrator Level) to define the administrator service availability for each extension’s Class of Service. Input Data Class of Service Number 01-15 Related Prog.
  • Page 143 Program 20: System Option Setup 20-07: Class of Service Options (Administrator Level) Input Data(Cont’d) Related Prog. No. Item Input Data Default* Program 20-07-14 VRS General Message Listen Enables/disables extension’s ability to dial 4 or Service 11-10-21 Code 711 and listen to the General Message 20-07-15 VRS General Message Record Enables/disables extension’s ability to dial Service Code...
  • Page 144 Program 20: System Option Setup 20-08: Class of Service Options (Outgoing Call Service) Description Use Program 20-08 : Class of Service Options (Outgoing Call Service) to define the Outgoing call feature availability for each extension’s Class of Service. Input Data Class of Service Number 01-15 Related...
  • Page 145 Program 20: System Option Setup 20-08: Class of Service Options (Outgoing Call Service) Input Data(Cont’d) Related Prog. No. Item Input Data Default* Program 20-08-15 Block Outgoing Caller ID Enable (1) or disable (0) the system’s ability to 0 : Off automatically block outgoing Caller ID information when 14-01-20 1 : On...
  • Page 146 Program 20: System Option Setup 20-09 : Class of Service Options (Incoming Call Service) Description Use Program 20-09 : Class of Service Options (Incoming Call Service) to define the incoming call feature availability for each extension’s Class of Service. Input Data Class of Service Number 01-15 Related...
  • Page 147 Program 20: System Option Setup 20-09 : Class of Service Options (Incoming Call Service) Telephone Programming Instructions To enter data for Program 20-09(Class of Service Options(Incoming Call Service)): 1. Enter the programming mode. 2. Enter 20 09 20-09-01 F-Cls1   2nd Call DID OR0 3.
  • Page 148 Program 20: System Option Setup 20-10 : Class of Service Options (Answer Service) Description Use Program 20-10 : Class of Service Options (Answer Service) to define the answer feature availability for each extension’s Class of Service. Input Data Class of Service Number 01-15 Related Prog.
  • Page 149 Program 20: System Option Setup 20-10: Class of Service Options (Answer Service) Telephone Programming Instructions To enter data for Program 20-10(Class of Service Options(Answer Service)): 1. Enter the programming mode. 2. Enter 20 10 20-10-01 F-Cls1   Call Pickup 3. Enter the number of the item you want to program. 20-10-xx F-Clsxx xxxxx 4.
  • Page 150 Program 20: System Option Setup 20-11 : Class of Service Options (Hold/Transfer Service) Description Use Program 20-11 : Class of Service Options (Hold/Transfer Service) to define the Hold and Transfer feature availability for each extension’s Class of Service. Input Data Class of Service Number 01-15 Related...
  • Page 151 Program 20: System Option Setup 20-11 : Class of Service Options (Hold/Transfer Service) Input Data(Cont’d) Related Prog. No. Item Input Data Default* Program 20-11-15 VRS Personal Greeting Enables/disables extension’s ability to dial Service Code 713 to record, listen to or erase the Personal Greeting Message.
  • Page 152 Program 20: System Option Setup 20-12 : Class of Service Options (Charging Cost Service) Description Use Program 20-12 : Class of Service Options (Charging Cost Service) to define the Charging Cost feature availability for each extension’s Class of Service. Input Data Class of Service Number 01-15 Related...
  • Page 153 Program 20: System Option Setup 20-13 : Class of Service Options (Supplementary Service) Description Use Program 20-13 : Class of Service Options (Supplementary Service) to define the supplementary feature availability for each extension’s. Input Data Class of Service Number 01-15 Related Prog.
  • Page 154 Program 20: System Option Setup 20-13 : Class of Service Options (Supplementary Service) Input Data(Cont’d) Related Prog. No. Item Input Data Default* Program 20-13-15 Barge In, Initiate Enables/disables Barge In at initiating extension. 20-13-16 Barge In, Receive Blocks/allows Barge In at the receiving extension. 20-13-17 Barge In Tone/Display Use this option to enable/disable the Barge In tone.
  • Page 155 Program 20: System Option Setup 20-13 : Class of Service Options (Supplementary Service) Input Data(Cont’d) Related Prog. No. Item Input Data Default* Program 20-13-31 Connected Line identification (COLP) 20-13-32 Deny Multiple Barge-In Enable (1) or disable (0) the extension’s ability to have multiple user’s Barge In to their conversation.
  • Page 156 Program 20: System Option Setup 20-14 : Class of Service Options for DISA/E&M Description Use Program 20-14 : Class of Service Options for DISA/E&M to enable/disable DISA and tie line Class of Service options. You assign a DISA Class of Service to DISA users in Program 25-09. Assign tie line Classes of Service in 34-02.
  • Page 157 Program 20: System Option Setup 20-14 : Class of Service Options for DISA/E&M Input Data(Cont’d) Related Prog. No. Item Input Data Default Program 20-14-09 Forced Trunk Disconnect <Not for ISDN T-point> This option enables or disables a tie trunk caller’s ability to use Forced Trunk Disconnect (Service Code *26).
  • Page 158 Program 20: System Option Setup 20-15: Ring Cycle Setup Description Use Program 20-15 : Ring Cycle Setup to define the ringing cycles for each ring type. Input Data Related Prog. No. Incoming Ring Type Ring Cycle No. Default Program 20-15-01 Normal Incoming Call on Trunk 20-15-02 PBX,CES incoming Call...
  • Page 159 Program 20: System Option Setup 20-15: Ring Cycle Setup Telephone Programming Instructions To enter data for Program 20-15(Ring Cycle Setup): 1. Enter the programming mode. 2. Enter 20 15 20-15-01   TRK Normal INC 3. Enter the number of the item you want to program. 20-15-xx xxxxx 4.
  • Page 160 Program 20: System Option Setup 20-16: Selectable Display Messages Description Use Program 20-16 : Selectable Display Messages to enter the Selectable Display Messages. There are 20 alphanumeric messages, up to 16 characters long. Use the following chart when programming messages. Number of pressing the Key ¥...
  • Page 161 Program 20: System Option Setup 20-16: Selectable Display Messages Default Message Number Message MEETING_BY_##:## ROOM_ -_ ####### COME BACK ##:## CALL_ ########## CALL_AFTER_##:## LUNCH_BACK_##:## B.TRIP_BACK##/## B.TRIP########## GONE_FOR_THE_DAY DAY_OFF_BY_##/## MESSAGE_11 MESSAGE_12 MESSAGE_13 MESSAGE_14 MESSAGE_15 MESSAGE_16 MESSAGE_17 MESSAGE_18 MESSAGE_19 MESSAGE_20 Conditions “_” means space. Feature Cross Reference Selectable Display Messages Programming Manual...
  • Page 162 Program 20: System Option Setup 20-16: Selectable Display Messages Telephone Programming Instructions To enter data for Program 20-16(Selectable Display Messages): 1. Enter the programming mode. 2. Enter 20 16 20-16-01TxtMsg1 MEETING 3. Enter the number of the item you want to program. 20-16-xxTxtMsgxx xxxxx 4.
  • Page 163 Program 20: System Option Setup 20-17: Operator’s Extension Description Use Program 20-17 : Operator’s Extension to designate an operator. When an extension user dials “0” or “9” (defined by Program 11-01 Type 5), calls go to the operator selected in this program. If you don’t assign an extension in Program 90-11-01, system alarms appear on the extension assigned in this option.
  • Page 164 Program 20: System Option Setup 20-18: Service Tone Timers Description Use Program 20-18 : Service Tone Timer to set the values for the system service tone timers. Refer to the following chart for a description of each option, its range and default setting. Input Data Related Prog.
  • Page 165 Program 20: System Option Setup 20-18: Service Tone Timers Telephone Programming Instructions To enter data for Program 20-18(Service Tone Timers): 1. Enter the programming mode. 2. Enter 20 18 20-18-01   Ext DT Time30 3. Enter the number of the item you want to program. 20-18-xx xxxxx 4.
  • Page 166 Program 20: System Option Setup 20-19: System Options for Caller ID Description Use Program 20-19 : System Options for Caller ID to define the system options for the Caller ID feature. Input Data Prog. No. Item Input data Default 20-19-01 Caller ID Displaying Format if Displaying Digits are 0 : First 10 digits more than 12 digits.
  • Page 167 Program 20: System Option Setup 20-20: Message Setup for Non-Caller ID Data Description Use Program 20-20 : Message Setup for Non-Caller ID Data to define the messages which will be displayed when no Caller ID information is received. Input Data Prog.
  • Page 168 Program 20: System Option Setup 20-21: System Option for Long Conversation Description Use Program 20-21 : System Options for Long Conversation to define the system options for the Long Conversation feature. Input Data Prog. No. Item Input data Default 20-21-01 Long Conversation Alarm 1 0-64800(sec.) The warning tone for long toll calls sounds after this...
  • Page 169 Program 20: System Option Setup 20-23: System Option for CTI Service Description Use Program 20-23 : System Options for CTI Service to define the system options for the CTI feature. Input Data Prog. No. Item Input data Default 20-23-01 Delayed ring timer for CTI 0-64800(sec.) 20-23-02 ALERT reply time (CTI)
  • Page 170 Program 20: System Option Setup 20-25: ISDN Options Description Use Program 20-25 : ISDN Options to define the ISDN system options. Input Data Prog. No. Item Input data Default 20-25-01 Send the Release Message After Subscriber Hang Up 0 : Service Off 1 : Service On 20-25-02 Progress Indicate Information element detect...
  • Page 171 Program20: System Option Setup 20-25: ISDN Options COPY Telephone Programming Instructions To enter data for Program 20-25(ISDN Options): 1. Enter the programming mode. 2. Enter 20 25 20-25-01   Send ReleaseMsg1 3. Enter the number of the item you want to program. 20-25-xx xxxxx 4.
  • Page 172 Program 20: System Option Setup 20-26: Multiplier for Charge Cost Description Use Program 20-26 : Multiplier for Charge Cost to define the amount that the Network charge units will be increased by. Input Data Class of Service Number 01-15 Prog. No. Item Input data Default...
  • Page 173 Program 21: Outgoing Call Setup 21-01: System Options for Outgoing Calls Description Use Program 21-01 : System Options for Outgoing Calls to set the system options for Outgoing Call Service. Input Data Prog. No. Item Input data Default Related Program 0 : Route to Priority order 14-05 21-01-01...
  • Page 174 Program21: Outgoing Call Setup 21-01: System Option for Outgoing Calls Input Data(Cont’d) Prog. No. Item Input data Default Related Program 21-01-14 Forced Account Code Inter-digit 0-64800(sec.) Timer The system waits this interval for a user to enter a Forced Account code. 21-01-15 Outgoing Disable- on Incoming Line 0 : Service Off...
  • Page 175 Program 21: Outgoing Call Setup 21-02: Trunk Group Routing for Extensions COPY Description Use Program 21-02 : Trunk Group Routing for Extensions to assign Program 14-06 routes to extensions. Input Data Extension Number Max. 4 digits Day/ Night Mode Route table number Default Related Program 14-06...
  • Page 176 Program 21: Outgoing Call Setup 21-03: Trunk Group Routing for Trunks COPY Description Use Program 21-03 : Trunk Group Routing for Trunks to set the Trunk Route Table for Automatic External Call Forward. The Route Table is set in Program 14-06. Input Data Trunk Port Number 1-51...
  • Page 177 Program 21: Outgoing Call Setup 21-04: Toll Restriction Class for Extensions COPY Description Use Program 21-04 : Toll Restriction Class for Extensions to assign a Toll Restriction class to an extension. The details of Toll Restriction are defined in Program 21-05 and 21-06. Input Data Max.
  • Page 178: Restriction

    Program 21: Outgoing Call Setup 21-05: Toll Restriction Class Description Use Program 21-05 : Toll Restriction Class to set the system’s Toll Restriction classes (1-15). Input Data Toll Restriction Class Number 1-15 Related Prog. No. Item Input Data Description Program 21-05-01 International Call This...
  • Page 179: Setup

    Program 21: Outgoing Call Setup 21-05: Toll Restriction Class Input Data(Cont’d) Prog. No. Item Input Data Description Related Program 21-05-12 PBX Call Restriction 0 : Disable Use this option to set how the system Toll 1 : Enable Restricts calls over PBX trunks. If you enable PBX Toll Restriction, the system begins Toll Restriction after the PBX access code.
  • Page 180 Program 21: Outgoing Call Setup 21-05: Toll Restriction Class Feature Cross Reference Toll Restriction Telephone Programming Instructions To enter data for Program 21-05(Toll Restriction Class): 1. Enter the programming mode. 2. Enter 21 05 21-05-01TolCls1 Int’l Rest TBL 0 3. Enter the number of the item you want to program. 21-05-xx TolClsxx xxxxx 4.
  • Page 181: Code Table

    Program 21: Outgoing Call Setup 21-06: Toll Restriction Table Data Setup Description Use Program 21-06 : Toll Restriction Table Data Setup to set the system’s Toll Restriction data. Dial 1-9, 0, *, # can be entered in each table. Input Data Prog.
  • Page 182 Program 21: Outgoing Call Setup 21-06: Toll Restriction Table Data Setup Input Data(Cont’d) Prog. No. Item Table Input Data Default Description 21-06-08 PBX Access Code Dial (Up to No setting Use this option to enter the PBX 2 digits) Access Code. When the system is behind a PBX, this is the code users dial to access a PBX trunk.
  • Page 183 Program 21: Outgoing Call Setup 21-06: Toll Restriction Table Data Setup Telephone Programming Instructions To enter data for Program 21-06(Toll Restriction Table Data Setup): 1. Enter the programming mode. 2. Enter 21 06 21-06-01IntTBL1 Rest TBL 3. Enter the number of the item you want to program. 21-06-xxIntTBLx xxxxx 4.
  • Page 184 Program 21: Outgoing Call Setup 21-07: Toll Restriction Override Password Setup Description Use Program 21-07 - Toll Restriction Override Password Setup to assign Toll Restriction Override codes to extension ports. Each code must be four digits long, using any combination of 0-9, # and *. Each extension can have a separate code, or many extensions can share the same override code.
  • Page 185 Program 21: Outgoing Call Setup 21-08: Repeat Dial Setup Description Use Program 21-08 : Repeat Dial Setup to define the automatic Repeat Dial data. Input Data Related Prog. No. Item Input Data Default Program 21-08-01 Repeat Redial Count Set how many times a Repeat Redial will automatically 0-255 repeat if the call does not go through.
  • Page 186 Program 21: Outgoing Call Setup 21-09: Dial Block Setup Description Use Program 21-09 : Dial Block Setup to defines the Dial Blocking Toll Restriction Class and Dial Block Password to be used by the Supervisor extension. Input Data Related Prog. No. Item Input Data Default...
  • Page 187 Program 21: Outgoing Call Setup 21-10: Dial Block Restriction Class Per Extensions Description Use Program 21-10 : Dial Block Restriction Class Per Extensions to define the Toll Restriction Class to each extension when the extension is set for Dial Block Restriction. If this data is “0”, Toll Restriction Class follows Program 21-09-01.
  • Page 188 Program 21: Outgoing Call Setup 21-11: Extension Ringdown (Hotline) Assignment COPY Description Use Program 21-11 : Extension Ringdown (Hotline) Assignment to define the Hotline destination number for each extension number. Input Data Extension Number Max. 4 digits Hotline Destination Number Default Related Program 0-9,*,#, Pause, Hooking, @(Code to wait for response)
  • Page 189 Program 21: Outgoing Call Setup 21-12: ISDN Calling Party Number Setup for Trunks COPY Description Use Program 21-12 : ISDN Calling Party Number Setup for Trunks to assign Calling Party Numbers for each trunk (maximum 16 digits per entry). When a call is made by an extension which does not have an Extension Calling Number assigned (Program 21-13), the system sends the calling number for the ISDN trunk defined in 21- If the Calling Party Number is assigned in both Programs 21-12 and 21-13, the system sends the data in Note:...
  • Page 190 Program 21: Outgoing Call Setup 21-13: ISDN Calling Party Number Setup for Extensions Description Use Program 21-13 : ISDN Calling Party Number Setup for Extensions to assign each extension a Calling Party Number (maximum 16 digits per entry). The calling number is the subscriber number of the dial-in number. When a call is made by an extension which does not have an Extension Calling Number assigned (Program 21-12), the system sends the calling number for the ISDN trunk defined in Program 21-13.
  • Page 191 Program 21: Outgoing Call Setup 21-14 : Walking Toll Restriction Password Setup Description Use Program 21-14 : Walking Toll Restriction Password Setup to assign the password and Toll Restriction Class for Walking Toll Restriction. Each code is six digits long, using any combination of 0-9, # and *. Input Data ID Table Number 1-500...
  • Page 192 Program 21: Outgoing Call Setup 21-15: Individual Trunk Group Routing for Extensions Description Use Program 21-15 : Individual Trunk Group Route for Extensions to designate the alternate trunk access route accessed when a user dials the Alternate Trunk Route Access Code. Refer to Program 11-09-02 - Alternate Trunk Access Code when setting up alternate trunk codes.
  • Page 193 Program 21: Outgoing Call Setup 21-17: Not Used Description This command is currently not used. Programming Manual...
  • Page 194 Program 21: Outgoing Call Setup 21-18: Not Used Description This command is currently not used. Programming Manual...
  • Page 195 Program21: Outgoing Call Setup 21-19: Not Used Description This command is currently not used. Programming Manual...
  • Page 196 Program 21: Outgoing Call Setup For your Notes - Programming Manual...
  • Page 197 Program 22: Incoming Call Setup 22-01: System Options for Incoming Calls Description Use Program 22-01 : System Options for Incoming Calls to define the system options for incoming calls. Input Data Prog. No. Item Input data Default Description Related Program 22-01-01 Incoming Call 0 : Intercom Call...
  • Page 198 Program 22: Incoming Call Setup 22-01: System Options for Incoming Calls Input Data(Cont’d) Prog. No. Item Input data Default Description Related Program 22-01-10 VRS Waiting 0 : Enable always This program set up the operation 22-14 Message 1 : Charge by mode for Auto Attendant and 22-15 Operation...
  • Page 199 Program 22: Incoming Call Setup 22-02: Incoming Call Trunk Setup COPY Description Use Program 22-02 : Incoming Call Trunk Setup to assign the incoming trunk type for each trunk. There is one item for each Night Service Mode. Input Data Trunk Port Number 1-51 Day/Night...
  • Page 200 Program 22: Incoming Call Setup 22-03: Trunk Ring Tone Setup COPY Description Use Program 22-03 : Trunk Ring Tone Setup to select the ring tone range for the trunk. The trunk uses a ring tone within the range selected when it rings an extension. There are three ring tones available. Input Data Trunk Port Number 1-51...
  • Page 201 Program 22: Incoming Call Setup 22-03: Trunk Ring Tone Setup COPY Telephone Programming Instructions To enter data for Program 22-03(Trunk Ring Tone Setup): 1. Enter the programming mode. 2. Enter 22 03 22-03-01 Trunk1 Ring Tone Pat 0 3. Enter the number of the item you want to program. 22-03-xx Trunkxx xxxxx 4.
  • Page 202 Program 22: Incoming Call Setup 22-04: Incoming Extension Ring Group Assignment Description Use Program 22-04 : Incoming Extension Ring Group Assignment to assign extensions to Ring Groups. Calls ring extensions according to Ring Group programming. Use Program 22-05 to assign trunks to Ring Groups. IRG can have up to 32 extension numbers assigned.
  • Page 203 Program 22: Incoming Call Setup 22-05: IRG Assignment for Normal Ring Trunk COPY Description Use Program 22-05 : Incoming Trunk Ring Group Assignment to assign trunks to incoming Ring Groups. Input Data Trunk Port Number 1-51 Day/Night Related Incoming Group Number Default Description Mode...
  • Page 204 Program 22: Incoming Call Setup 22-06: Normal Incoming Ring Mode Description Use Program 22-06 : Normal Incoming Ring Mode to define whether or not an extension should ring for the Normal Incoming Ring Mode. Input Data Extension Number Max. 4 digits Day/Night Incoming Group Number Default...
  • Page 205 Program 22: Incoming Call Setup 22-07: DIL Assignment Description Use Program 22-07 : DIL Assignment to assign the destination extension or Department Calling Group for each DIL Incoming trunk. A DIL rings an extension directly, without any other Access Map or Ring Group programming. If an extension has a line key, the DIL rings the line key.
  • Page 206 Program 22: Incoming Call Setup 22-08: DIL/IRG No Answer Destination COPY Description For DIL Delayed Ringing, use Program 22-08 : DIL/IRG No Answer Destination to assign the DIL No Answer Ring Group. An unanswered DIL rings this group after the DIL No Answer Time expires (Program 22-01-04). DIL Delayed Ringing can also reroute outside calls ringing a Ring Group.
  • Page 207 Program 22: Incoming Call Setup 22-09: DID Basic Data Setup Description Use Program 22-09 : DID Basic Data Setup to define the basic setting of Dial-In incoming calls for each trunk group. Input Data Trunk Group Number 1-25 Prog. No. Item Input Data Default...
  • Page 208 Program 22: Incoming Call Setup 22-09: DID Basic Data Setup Telephone Programming Instructions To enter data for Program 22-09(DID Basic Data Setup): 1. Enter the programming mode. 2. Enter 22 09 22-09- 01TrkGrp1   3. Enter the number of the item you want to program. 22-09- xxTrkGrpxx 4.
  • Page 209 Program 22: Incoming Call Setup 22-10: DID Translation Table Setup Description Use Program 22-10 : DID Translation Table Setup to specify the size of the DID Translation Tables. There are 2000 Translation Table entries that you can allocate among 20 Translation Tables. Input Data Conversion Table Area Number 1-20...
  • Page 210 Program 22: Incoming Call Setup 22-10: DID Translation Table Setup Telephone Programming Instructions To enter data for Program 22-10(DID Translation Table Setup): 1. Enter the programming mode. 2. Enter 22 10 22-10-01C-Area1 1st Start 3. Enter the number of the item you want to program. 22-10-xxC-Areaxx xxxxx 4.
  • Page 211 Program 22: Incoming Call Setup 22-11: DID Translation Number Conversion Description Use Program 22-11 : DID Translation Number Conversion to specify for each Translation Table entry (2000): • The digits received by the system (eight max.) • The extension the system dials after translation (36 digits max.) •...
  • Page 212 Program 22: Incoming Call Setup 22-11: DID Translation Number Conversion Input Data Conversion Table Number 1-2000 Prog. No. Item Input Data Default 22-11-01 Received Number Max. 8 digits see Default 22-11-02 Target Number Max. 36 digits see Default 22-11-03 DID Name Max.
  • Page 213 Program 22: Incoming Call Setup 22-11: DID Translation Number Conversion Feature Cross Reference Direct Inward Dialing (DID) Telephone Programming Instructions To enter data for Program 22-11(DID Translation Number Conversion): 1. Enter the programming mode. 2. Enter 22 11 22-11-01 TBL1 Recv No 00 3.
  • Page 214 Program 22: Incoming Call Setup 22-12: DID Intercept Ring Group Description For each DID Translation Table, use Program 22-12 : DID Intercept Ring Group to define the first destination group for DID calls. Depending on the entry in Program 22-09 and 22-11, the incoming calls will route to the first destination group by the following;...
  • Page 215 Program 22: Incoming Call Setup 22-12: DID Intercept Ring Group Telephone Programming Instructions To enter data for Program 22-12(DID Intercept Ring Group): 1. Enter the programming mode. 2. Enter 22 12 22-12-01C-Area1 Mode1 3. Enter the number of the item you want to program. 22-12-xxC-Areaxx xxxxx 4.
  • Page 216 Program 22: Incoming Call Setup 22-13 DID Trunk Group to Translation Table Assignment Description Use Program 22-13 : DID Trunk Group to Translation Table Assignment to assign the DID Trunk Groups to DID Translation Tables. DID trunks should be in their own group. If you have more than one type of DID trunk, put each type in a separate Trunk Group.
  • Page 217 Program 22: Incoming Call Setup 22-14: VRS Waiting Delayed Message for IRG Description Use Program 22-14 : VRS Waiting Delayed Message for IRG to define for each incoming ring group the timers, VRS message number and tone kind for VRS Waiting Message. Input Data Incoming Ring Group Number 1-25...
  • Page 218 Program 22: Incoming Call Setup 22-14: VRS Waiting Delayed Message for IRG Telephone Programming Instructions To enter data for Program 22-14(VRS Waiting Delayed Message for IRG): 1. Enter the programming mode. 2. Enter 22 14 22-14- 01INCGrp1   3. Enter the number of the item you want to program. 22-14- xxINCGrpxx 4.
  • Page 219 Program 22: Incoming Call Setup 22-15: VRS Waiting Message for Department Group Description Use Program 22-15 : VRS Waiting Message for Department Group to define for each Department (Extension) Group the timers, VRS message number and tone kind for VRS Waiting Message. Input Data Extension Group Number 01-32...
  • Page 220 Program 22: Incoming Call Setup 22-15: VRS Waiting Message for Department Group Telephone Programming Instructions To enter data for Program 22-15(VRS Waiting Message for Department Group): 1. Enter the programming mode. 2. Enter 22 15 22-15-01 Ex.Gr1 MSG1 StatTM0 3. Enter the number of the item you want to program. 22-15-xx Ex.Grxx xxxxx 4.
  • Page 221 Program 23: Answer Features Setup 23-01: Not used Description This feature is currently not available. Programming Manual...
  • Page 222: Group

    Program 23: Answer Features Setup 23-02: Call Pickup Groups Description Use Program 23-02 : Call Pickup Groups to assign extensions to Call Pickup Groups. This program also lets you assign an extension’s Call Pickup Group priority. If two extensions in a group are ringing at the same time, Group Call Pickup intercepts the highest priority extension first.
  • Page 223 Program 23: Answer Features Setup 23-03: Universal Answer/Auto Answer COPY Description Use Program 23-03 : Universal Answer/Auto Answer to assign trunk routes 1-25 (set in Program 14-06) to extensions for Universal Answer. If the call ringing the paging system is in an extension’s assigned route, the user can dial the Universal Answer code (843) to pick up the call.
  • Page 224 Program 23: Answer Features Setup 23-04: Ringing Line Preference for Virtual Extensions COPY Description Use Program 23-04 : Ringing Line Preference for Virtual Extensions to set the off-hook automatic response priority for calls ringing virtual extension keys on a telephone. Input Data Extension Number Max.
  • Page 225 Program 24: Hold/Transfer Setup 24-01: System Options for Hold Description Use Program 24-01 : System Options for Hold to define the system options for the Hold feature Input Data Related Prog. No. Item Input Data Default Program 24-01-01 Hold Recall Time 0-64800(Sec.)...
  • Page 226 Program 24: Hold/Transfer Setup 24-01: System Options for Hold Telephone Programming Instructions To enter data for Program 24-01(System Options for Hold): 1. Enter the programming mode. 2. Enter 24 01 24-01-01   Hold Recall90 3. Enter the number of the item you want to program. 24-01-xx xxxxx 4.
  • Page 227 Program 24: Hold/Transfer Setup 24-02: System Options for Transfer Description Use Program 24-02 : System Options for Transfer to define the system options for Transfer feature. Input Data Related Prog. No. Item Input Data Default Program 24-02-01 Busy Transfer 0 : Disable Use this option to prevent or allow extensions to 1 : Enable Transfer calls to busy extensions.
  • Page 228 Program 24: Hold/Transfer Setup 24-02: System Options for Transfer Telephone Programming Instructions To enter data for Program 24-02(System Options for Transfer): 1. Enter the programming mode. 2. Enter 24 02 24-02-01   Busy Ext TRF 0 3. Enter the number of the item you want to program. 24-02-xx xxxxx 4.
  • Page 229 Program 24: Hold/Transfer Setup 24-03: Park Group COPY Description Use Program 24-03 : Park Group to assign an extension to a Park Group. The system allows a total of 64 Park Groups. An extension can only pick up a call parked in orbit by an extension in its own group. Input Data Extension Number Max.
  • Page 230 Program 24: Hold/Transfer Setup 24-04: Automatic Trunk-to-Trunk Transfer Target Setup Description Use Program 24-04 : Automatic Trunk-to-Trunk Transfer Target Setup to assign the Abbreviated Dialing number bin which should be used as the destination of the Automatic Trunk-to-Trunk Transfer. Input Data Trunk Port Number 1-51 Abbreviated...
  • Page 231 Program 24: Hold/Transfer Setup 24-05: Department Group Transfer Target Setup Description Use Program 24-05 : Department Group Transfer Target Setup to assign the Abbreviated Dialing bin which is used as the destination of the extension for the Department Group. Input Data Department Group Number 1-32 Abbreviated...
  • Page 232 Program 24: Hold/Transfer Setup 24-06: Fixed Call Forwarding Description For each extension/virtual extension port, use Program 24-06 : Fixed Call Forwarding to assign the Fixed Call Forwarding Type (0-4) and the destination extension/virtual extension. The following chart shows the Fixed Call Forwarding types: Fixed Call Forwarding Type Description...
  • Page 233 Program 24: Hold/Transfer Setup 24-06: Fixed Call Forwarding Telephone Programming Instructions To enter data for Program 24-06(Fixed Call Forwarding): 1. Enter the programming mode. 2. Enter 24 06 24-06-01 TEL200 Fix Cfwd Type 0 3. Enter the number of the item you want to program. 24-06-xx TELxxxx 4.
  • Page 234 Program 24: Hold/Transfer Setup 24-07: Fixed Call Forwarding Off-Premise Description Use Program 24-07 : Fixed Call Forwarding Off-Premise to assign the Fixed Call Forwarding Off-Premise telephone number for each extension/virtual extension. The off-premise destination can be up to 36 digits long, using 0-9, *, # and P (pause).
  • Page 235 Program 25: DID/DISA Setup 25-01: DID/DISA Line Basic Data Setup Description Use Program 25-01 : DID/DISA Line Basic Data Setup to define the basic setting of each DID/DISA line. Input Data Trunk Port Number 1-51 Prog. No. Item Input Data Default Related Program...
  • Page 236 Program 25: DID/DISA Setup 25-02: DID/DISA Talkie Description Use Program 25-02 : DID/DISA Talkie to assign the VRS message number to be used as the Automated Attendant Error Message for each trunk which is assigned as a DID/DISA. Input Data Trunk Port Number 1-51 Day/Night...
  • Page 237 Program 25: DID/DISA Setup 25-03: DID/DISA Transfer Ring with Incorrect Dialing Description Use Program 25-03 : DID/DISA Transfer Ring Group with Incorrect Dialing to set what happens to a call when the DISA caller dials incorrectly or waits too long to dial. The call can either disconnect (0) or Transfer to an alternate destination (a ring group or voice mail).
  • Page 238 Program 25: DID/DISA Setup 25-04: DID/DISA Transfer Ring Group with No Answer/Busy Description Use Program 25-04 : DID/DISA Transfer Ring Group with No Answer/Busy to set the operating mode of each DISA trunk. This sets what happens to the call when the DISA caller calls a busy or unanswered extension. The call can either disconnect (0) or Transfer to an alternate destination (a ring group or voice mail).
  • Page 239 Program 25: DID/DISA Setup 25-05: DID/DISA Error Message Assignment Description Use Program 25-05 : DID/DISA Error Message Assignment to assign the VRS message number to be used as the Automated Attendant error message. For each DID/DISA trunk that the VRS will answer, enter the VRS message (1-48) the outside caller hears if they dial incorrectly.
  • Page 240 Program 25: DID/DISA Setup 25-06: DID/DISA One Digit Code Attendant Setup Description Use Program 25-06 : DID/DISA One-Digit Code Attendant Setup to set up single digit dialing through the VRS. This gives VRS callers single key access to extensions, the company operator, Department Calling Groups and Voice Mail.
  • Page 241 Program 25: DID/DISA Setup 25-06: DID/DISA One Digit Code Attendant Setup Telephone Programming Instructions To enter data for Program 25-06(DID/DISA One Digit Code Attendant Setup): 1. Enter the programming mode. 2. Enter 25 06 25-06-01Attend 1 Recv1 MSG No=0 3. Enter the number of the item you want to program. 25-06-xxAttendxx xxxxx 4.
  • Page 242 Program 25: DID/DISA Setup 25-07: System Timer for DID/DISA Description Use Program 25-07 : System Timers for DID/DISA to set the value for the system timers which affect DID and DISA. Refer to the following chart for a description of each option, its range and default setting. Input Data Related Prog.
  • Page 243 Program 25: DID/DISA Setup 25-07: System Timer for DID/DISA Conditions None Feature Cross Reference Direct Inward System Access (DISA) Telephone Programming Instructions To enter data for Program 25-07(System Timers for DID/DISA): 1. Enter the programming mode. 2. Enter 25 07 25-07-01  ...
  • Page 244 Program 25: DID/DISA Setup 25-08: DISA User ID Setup Description Use Program 25-08 : DISA User ID Setup to set the 6-digit DISA password for each user. There are 15 users each with one 6-digit password. Input Data DISA User Number 1-15 Password Default...
  • Page 245 Program 25: DID/DISA Setup 25-09: Class of Service for DISA Users Description Use Program 25-09 : Class of Service for DISA Users to set the DISA Class of Service for each user. When a DISA caller enters a password (defined in Program 25-08), the system identifies the user and associates the appropriate DISA Class of Service with the call.
  • Page 246 Program 25: DID/DISA Setup 25-10: Trunk Group Routing for DISA Description Use Program 25-10 : Trunk Group Routing for DISA to assign the Trunk Group route chosen when a user places a DISA call into the system and dials 9. Set Trunk Group Routing in Program 14-06. Enable or disable the DISA caller’s ability to dial 9 in Program 20-14-02.
  • Page 247 Program 25: DID/DISA Setup 25-11: DISA Toll Restriction Class Description For systems that use Toll Restriction, use Program 25-11 : DISA Toll Restriction Class to assign a Toll Restriction Class (1-15) to each DISA user (1-15). The system uses the Toll Restriction Class you enter in Program 21-05 and 21-06.
  • Page 248 Program 25: DID/DISA Setup 25-12: Alternate Trunk Group Routing for DISA Description Use Program 25-12 : Alternate Trunk Group Routing for DISA to define the trunk route selected when a DISA caller dials the Alternate Trunk Access Code. The route selected is based on the DISA caller’s Class of Service, which is in turn determined by the password the caller dials.
  • Page 249 Program 25: DID/DISA Setup 25-13: System Option for DISA Description Use Program 25-13 : System Option for DISA to enter the password DISA callers must dial before the system will allow them to record, listen to and or erase the VRS messages. This program also is used to define additional DISA call options.
  • Page 250 Program 25: DID/DISA Setup 25-13: System Option for DISA Telephone Programming Instructions To enter data for Program 25-13(System Option for DISA): 1. Enter the programming mode. 2. Enter 25 13 25-13-01   Access PWD000000 3. Enter the number of the item you want to program. 25-13-xx xxxxx 4.
  • Page 251 Program 26: ARS Service & Least Cost Routing 26-01: Automatic Route Selection Service Description Use Program 26-01 : Automatic Route Selection Service to define the system options for Automatic Route Selection (ARS). Input Data Related Prog. No. Item Input Data Default Program 26-01-01...
  • Page 252 Program 26: ARS Service & Least Cost Routing 26-01: Automatic Route Selection Service Telephone Programming Instructions To enter data for Program 26-01(Automatic Route Selection Service): 1. Enter the programming mode. 2. Enter 26 01 26-01-01   ARS Service 3. Enter the number of the item you want to program. 26-01-xx xxxxx 4.
  • Page 253 Program 26: ARS Service & Least Cost Routing 26-02: Dial Analysis Table for ARS Description Use Program 26-02 : Dial Analysis Table for ARS to set pre-transaction tables for selecting Automatic Route Selection (ARS). • Service Type 1 (Route to Trunk Group Number) - the number routes to a trunk group. •...
  • Page 254 Program 26: ARS Service & Least Cost Routing 26-02: Dial Analysis Table for ARS Telephone Programming Instructions To enter data for Program 26-02(Dial Analysis Table for ARS): 1. Enter the programming mode. 2. Enter 26 02 26-02-01AnaTb1 Dial 3. Enter the number of the item you want to program. 26-02- xxAnaTbxxx 4.
  • Page 255 Program 26: ARS Service & Least Cost Routing 26-03: ARS Dial Treatment Description Use Program 26-03 : ARS Dial Treatments to assign the 15 Dial Treatments for automatic ARS Dialing translation. Assign Dial Treatments to Service Numbers (Trunk Groups) in Program 26-02. The ARS Dial Treatment options are: •...
  • Page 256 Program 26: ARS Service & Least Cost Routing 26-04: ARS Class of Service Description Use Program 26-04 : ARS Class of Service to set an extension’s ARS Class of Service. Automatic Route Selection uses ARS Class of Service when determining how to route an extension’s calls. Input Data Extension Number Max.
  • Page 257 Program 26: ARS Service & Least Cost Routing 26-05: LCR Carrier Table Description Use Program 26-05 : LCR Carrier Table to define the LCR Access Codes and routing options. These options include Authorization codes and Cost Centre Codes. Input Data Carrier Table Number 1-25 Related...
  • Page 258 Program 26: ARS Service & Least Cost Routing 26-06: LCR Authorization Code Table Description Use Program 26-06 : LCR Authorization Code Table to define the optional Authorization code (or PIN code) required by the Indirect Carrier. The Authorization code is inserted if set in Program 26-05-03. Input Data Authorization Related...
  • Page 259 Program 26: ARS Service & Least Cost Routing 26-07: LCR Cost Centre Code Table Description Use Program 26-07 : LCR Cost Centre Code Table to define the optional cost centre code required by the Indirect Carrier. The cost centre code is set for each extension. The cost centre code is inserted if set in Program 26- 05-04.
  • Page 260 Program 26: ARS Service & Least Cost Routing 26-08: LCR Manual Override Access Code Table Description Use Program 26-08 : LCR Manual Override Access Code Table to define the access codes that the users can dial to select an indirect carrier i.e. bypass the automatic selection of Program 26-02. Input Data Manual Override Access Code Table Number 1-10...
  • Page 261 Program 26: ARS Service & Least Cost Routing 26-09: LCR Manual Override Exemption Table Description Use Program 26-09 : LCR Manual Override Exemption Table to define the numbers that must not be sent via an indirect carrier when the user dials a Manual Override Access Code. The exemptions are normally Emergency Services that may not be supported by the indirect carrier.
  • Page 262 Program 26: ARS Service & Least Cost Routing For your Notes - Programming Manual...
  • Page 263 Program 30: DSS/DLS Console 30-01: Not used Description This command is currently not available. Programming Manual...
  • Page 264 Program 30: DSS/DLS Console 30-02: DSS Console Extension Assignment Description Use Program 30-02 : DSS Console Extension Assignment to identify which extensions have DSS Consoles assigned. • You can have up to 9 different DSS Consoles. A single extension can have up to 9 64-Button DSS Consoles (9 is the maximum allowed per system).
  • Page 265 Program 30: DSS/DLS Console 30-03: DSS Console Key Assignment COPY Description Use Program 30-03 : DSS Console Key Assignments to customize the key assignments for 64-Button DSS Consoles. A DSS Console key can have any function up to four digits long (e.g., extension number or Service Code).
  • Page 266 Program 30: DSS/DLS Console 30-02: DSS Console Extension Assignment Function Number Lists(Cont’d) Function Function Additional Data LED Indication Number Call Forward – Slow Blink Red : Forwarding state Busy or No Answer Rapid Blink Red : Forwarded state Call Forward - Slow Blink Red : Forwarding state Both Ring Rapid Blink Red : Forwarded state...
  • Page 267 Program 30: DSS/DLS Console 30-03: DSS Console Key Assignment COPY Function Number Lists(Cont’d) Function Function Additional Data LED Indication Number DND/ Call FWD None Override Call Message Waiting None Rapid Blink Red : Under Monitored Room Monitoring Slow Blink Red : Under Monitoring Handset Red On : Transmission Cut-Off Transmission cut-...
  • Page 268 Program 30: DSS/DLS Console 30-03: DSS Console Key Assignment COPY Function Number Lists(Cont’d) Function Function Additional Data LED Indication Number DND at Group No.01-32 None Department Group Call Calling Line Red On: Active Identification Restriction Mode Red On: CTI active Communication Rapid Blink Red : New message received Extension Number or...
  • Page 269 Program 30: DSS/DLS Console 30-03: DSS Console Key Assignment COPY 2)Appearance Functional Level (*00-*99) Function Function Additional Data LED Indication Number Trunk key Trunk Number (01-51) Park key Park Number (01-64) Default All DSS Console Key Number Function Number Additional Data DSS01 01(DSS Key) DSS02...
  • Page 270 Program 30: DSS/DLS Console 30-04: Not Used Description This command is currently not available. Programming Manual...
  • Page 271 Program 30: DSS/DLS Console 30-05: DSS Console Lamp Table Description Use Program 30-05 : DSS Console Lamp Table to defines the LED patterns for functions on each DSS console. Input Data Related Prog. No. Item Lamp Pattern Data Default Program 30-05-01 Idle Extension 0-3,5,7 (4,6: Not Used)
  • Page 272 Program 30: DSS/DLS Console 30-05: DSS Console Lamp Table Conditions None Feature Cross Reference Direct Station Selection (DSS) Console Telephone Programming Instructions To enter data for Program 30-05(DSS Console Lamp Table): 1. Enter the programming mode. 2. Enter 30 05 30-05-01  ...
  • Page 273 Program 31: External Speaker and Internal Paging 31-01: System Options for Internal/External Paging Description Use Program 31-01 : System Options for Internal/External Paging to define the system options for Internal / External Paging. The system shows the names you program on the telephone displays. Use the following chart when entering and editing text.
  • Page 274 Program 31: External Speaker and Internal Paging 31-01: System Options for Internal/External Paging COPY Conditions None Feature Cross Reference Paging, External Paging, Internal Telephone Programming Instructions To enter data for Program 31-01(System Options for Internal/External Paging): 1. Enter the programming mode. 2.
  • Page 275 Program 31: External Speaker and Internal Paging 31-02 Internal Paging Group Assignment COPY Description Use Program 31-02 : Internal Paging Group Assignment to assign extensions to Internal Paging Groups (i.e., Page Zones). The setting in this program also determines if the Internal Page Group can receive Internal All Call Paging.
  • Page 276 Program 31: External Speaker and Internal Paging 31-03: Internal Paging Group Settings   Description Use Program 31-03 : Internal Paging Group Settings to assign names to Internal Paging Groups (i.e., Page Zones) and to define the splash tone for Internal Paging. The system shows the names you program on the telephone displays.
  • Page 277 Program 31: External Speaker and Internal Paging 31-03: Internal Paging Group Settings Default Program Number Internal Paging Group Name Group 1 Group 2 31-03-01 Internal Paging Group Name Group 32 Conditions None Feature Cross Reference Paging, Internal Telephone Programming Instructions To enter data for Program 31-03(Internal Paging Group Settings): 1.
  • Page 278 Program 31: External Speaker and Internal Paging 31-04: External Paging Zone Group   Description Use Program 31-04 : External Paging Zone Group to assign each External Paging zone to an External Paging group. Users call the External Paging group when broadcasting announcements to the external zone. When programming, the zones on the PGDU are numbers 1-6.
  • Page 279 Program 31: External Speaker and Internal Paging 31-05: Incoming Ring Tone Audible on External Speaker COPY Description Use Program 31-05 : Incoming Ring Tone Audible on External Speaker to assign Universal Night Ans- wer ringing to each External Paging zone. For each trunk port (1-51), you make a separate entry for each External Paging zone (1-6).
  • Page 280 Program 31: External Speaker and Internal Paging 31-06: External Speaker Control Description Use Program 31-06 : External Speaker Control to define the settings for the external speaker using an amplifier. Input Data External Default Prog. No. Item Input Data Speaker No. 31-06-01 Broadcast Splash Tone Before Paging 0 : No tone...
  • Page 281 Program 31: External Speaker and Internal Paging 31-07: Combined Paging Assignments Description Use Program 31-07 : Combined Paging Assignments to assign an External Paging Zone (0-6) to an Internal Paging Zone (0-6) for Combined Paging. When an extension user makes a Combined Page, they simultaneously broadcast into both the External and Internal Zone.
  • Page 282 Program 31: External Speaker and Internal Paging 31-08: BGM on External Paging Description Use Program 31-08 : BGM on External Paging to set the Background Music option for each External Paging zone. If enabled, the system will play Background Music over the zone when it is idle. When programming, the zones on the PGDU Units are numbers 1-6.
  • Page 283 32: Door Box Setup Program 32-01 Door Box Timers Description Use Program 32-01 : Door Box Timers to assign the timers used for the Door Box. Input Data Related Prog. No. Item Input Data Default Program 32-01-01 0-64800(sec.) Door Box Answer Time A keyset user must answer Door Box chimes within this interval.
  • Page 284 Program 32: Door Box Setup 32-02: Door Box Ring Assignment Description Use Program 32-02 : Door Box Ring Assignments to assign the extension which will ring when a caller presses the associated Door Box’s call button. Input Data Door Box Number Day/Night Related Door Box Group Number...
  • Page 285 Program 32: Door Box Setup 32-03: Door Box Basic Setup Description Use Program 32-03 : Door Box Basic Setup to select the chime pattern and gain level for each Door Box. There are six distinctive chime patterns. The chime tones are defined in Program 80-01. Input Data Door Box Number Related...
  • Page 286 Program 32: Door Box Setup For your Notes - Programming Manual...
  • Page 287 33: Analogue Interface Ports Setup Program 33-01 Analogue Interface Port Type Setup Description Use Program 33-01 : Analogue Interface Port Type Setup to set the function of each software port on an Analogue Communications Interface. Each Analogue Interface Port can have only one function (input, output or none). Input Data Related Analogue Interface Port Number...
  • Page 288 Program 33: Analogue Interface Ports Setup 33-02: Analogue Interface Group Assignment Description Use Program 33-02 : Analogue Interface Group Assignment to assign Analogue Interface Ports (1-6) to Department Groups. There are 4 ACI Department Groups. An ACI port can only be in one group. Also use this program to set the ACI port’s priority.
  • Page 289 : SMDR and Account Code Setup Program 35 35-01: SMDR Options Description Use Program 35-01 : SMDR Options to set the SMDR (Station Message Detail Recording) options for the SMDR port. Refer to the following chart for a description of each option, its range and default setting. Input Data SMDR Port Number Related...
  • Page 290 Program 35: SMDR and Account Code Setup 35-01: SMDR Options Telephone Programming Instructions To enter data for Program 35-01 (SMDR Options): 1. Enter the programming mode. 2. Enter 35 01 35-01-01 SMDR-P1 Output Type  3. Enter the number of the item you want to program. 35-01-xx SMDR-Px xxxxx 4.
  • Page 291 35: SMDR and Account Code Setup Program 35-02: SMDR Output Options Description Use Program 35-02 : SMDR Options to set the SMDR (Station Message Detail Recording) options for the SMDR port. Refer to the following chart for a description of each option, its range and default setting. Input Data SMDR Port Number Related...
  • Page 292 Program 35: SMDR and Account Code Setup 35-02: SMDR Output Options Input Data(Cont’d) Related Prog. No. Item Input Data Default Program 35-02-10 0 : Not Output All Busy (ALB) Output 1 : Output 35-02-11 Walking Toll Restriction Table 0 : Not Output Number 1 : Output 35-02-12...
  • Page 293 35: SMDR and Account Code Setup Program 35-02: SMDR Output Options *Column 8(hh.…) : Ring Duration or Cost Indicate a ringing duration time at the extension for incoming call. And also, indicate the calling cost data for outgoing call. However the calling cost data is not exactly same value as the PTT’s calculation cost. <Note>Calling cost data will be provided from Line Provider by using Metering Pulse or “Advice of Charge”...
  • Page 294 Program 35: SMDR and Account Code Setup 35-03: SMDR Port Assignment for Trunk Group COPY Description Use Program 35-03 : SMDR Port Assignment for Trunk Group to assign the SMDR port for each trunk group. Input Data Trunk Group No. SMDR Port No.
  • Page 295 Program 35: SMDR and Account Code Setup 35-04: SMDR Port Assignment for Department Group COPY Description Use Program 35-04 : SMDR Port Assignment for Department Groups to assign the SMDR port for each Department Group. Input Data Department Group No. SMDR Port No.
  • Page 296 Program 35: SMDR and Account Code Setup 35-05: Account Code Setup Description Use Program 35-05 : Account Code Setup to set various Account Code options for an extension’s Class of Service. Assign a Class of Service to extensions in Program 20-06. Input Data Class of Service Number 1-15...
  • Page 297 35: SMDR and Account Code Setup Program 35-05: Account Code Setup Telephone Programming Instructions To enter data for Program 35-05 (Account code Setup): 1. Enter the programming mode. 2. Enter 35 05 35-05-01 F-Cls1 Account Code 3. Enter the number of the item you want to program. 35-05-xx F-Clsxx xxxxx 4.
  • Page 298 Program 35: SMDR and Account Code Setup 35-06: Verified Account Code Table Description Use Program 35-06 : Verified Account Code Table to enter Account Codes into the Verified Account Code list. You can enter up to 2000 codes from 3-16 digits long, using the characters 0-9 or #. Use the FLASH key to enter a wild card.
  • Page 299 : Voice Mail Setup Program 40 40-01: Voice Mail Basic Setup Description Use Program 40-01 : Voice Mail Basic Setup to define the basic operation of Voice Mail (DSPDB). Input Data Related Prog. No. Item Input Data Default Program 40-01-01 Exclusive Channel for Voice Mail 0-16 Specify the number of channels of...
  • Page 300 Program 40: Voice Mail Setup 40-02: Mailbox Setup Description Use Program 40-02 : Mailbox Setup to define the mailbox of the Voice Mail (DSPDB). There are a maximum of 300 mailboxes in the DSPDB. Use this program to set the box number and password linked to the extension number (or pilot number) for each mailbox.
  • Page 301 : Voice Mail Setup Program 40 40-03: Message Recording Setup Description Use Program 40-03 : Message Recording Setup to define the auto-answering operation of the Voice Mail (DSPDB). Input Data Related Prog. No. Item Input Data Default Program 40-03-01 Voice Mail Recording Time 1-10 (minute) 40-03-02 A Guidance message in case...
  • Page 302 Program 40: Voice Mail Setup 40-04: Live Recording Setup Description Use Program 40-04 : Live Recording Setup to define the conversation recording operation of the Voice Mail (DSPDB). Input Data Related Prog. No. Item Input Data Default Program 40-04-01 The Operation mode when destination 0 : Temporary Mailbox is not defined.
  • Page 303 : Voice Mail Setup Program 40 40-05: Call Information Setup Description Use Program 40-05 : Call Information Setup to define the incoming notice of the Voice Mail (DSPDBU). Input Data Related Prog. No. Item Input Data Default Program 40-05-01 Maximum number of outgoing call simultaneously 40-05-02 Trunk Route Number 0-25...
  • Page 304 Program 40: Voice Mail Setup 40-06: Voice Mail Automated Attendant Data Setup Description Use Program 40-06 : Voice Mail Automated Attendant Data Setup to define the outside lines to use the automated attendant recording operation of the Voice Mail (DSPDB). Input Data Trunk Port Number 1-51...
  • Page 305 : Voice Mail Setup Program 40 40-07: Voice Prompt Language Assignment for Voice Mail Description Use Program 40-07 : Voice Prompt Language Assignment for Voice Mail to specify the language to be used for the voice mail (DSPDB). Input Data Related Prog.
  • Page 306 Program 40: Voice Mail Setup 40-08: Voice Prompt Language Assignment for each Mail Box Description Use Program 40-08 : Voice Prompt Language Assignment for each Mail Box to specify the language to be used for the voice mail. Input Data Mail Box Number 1-300 Related...
  • Page 307 : Voice Mail Setup Program 40 40-09: Voice Mail Multiple Address Group Setup Description Use Program 40-09 : Voice Mail Multiple Address Group Setup to define the broadcast group of a Voice Mail (DSPDB) mailbox. Input Data Multiple Address Group Related Destination Box Number Box Number...
  • Page 308 Program 40: Voice Mail Setup 40-10: Voice Announcement Service Option Description Use Program 40-10 : Voice Announcement Service Option define the system options for the Voice Announcement feature. Input Data Related Prog. No. Item Input Data Default Program 40-10-01 VRS Fixed Message 0 : Not Used Enable (1) or disable (0) the system’s ability to 1 : Used...
  • Page 309 : Voice Mail Setup Program 40 40-10: Voice Announcement Service Option Telephone Programming Instructions To enter data for Program 40-10 (Voice Announce Service Option): 1. Enter the programming mode. 2. Enter 40 10 40-10-01   VRS Fixed Msg 1 3. Enter the number of the item you want to program. 40-10-xx xxxxx 4.
  • Page 310 Program 40: Voice Mail Setup 40-11: Pre-Amble Message Assignment Description In Program 40-11 : Pre-Amble Message Assignment to assign the VAU message number to be used as the Pre- amble Message for each trunk. When the extension user answers the incoming call, the assigned VAU message will be sent to the outside caller.
  • Page 311 Program 44: ARS/F-Route Setup 44-01: System Options for ARS/F-Route Description Use Program 44-01 : System Options for ARS/F-Route to define the system options for the ARS/F-Route feature. Input Data Related Prog. No. Item Input Data Default Program 0 : Not Used 44-01-01 ARS/F-Route Time Schedule 1 : Used...
  • Page 312 Program 44: ARS/F-Route Setup 44-02: Dial Analysis Table for ARS/F-Route Access Description Use Program 44-02 : Dial Analysis Table for ARS/F-Route Access to set the Pre-Transaction Table for selecting ARS/F-Route. • Service Type 1 (Extension number) The number goes to an extension after deleting the front digit(s). Additional data Assign the digit(s) to be deleted on top of the number for extension number usage.
  • Page 313 Program 44: ARS/F-Route Setup 44-02: Dial Analysis Table for ARS/F-Route Access Conditions None Feature Cross Reference Automatic Route Selection(ARS)/F-Route Telephone Programming Instructions To enter data for Program 44-02 (Dial Analysis Table for ARS/F-Route Access): 1. Enter the programming mode. 2. Enter 44 02 44-02-01A-TBL1 Dial 3.
  • Page 314 Program 44: ARS/F-Route Setup 44-03: Dial Analyze Extension Table Description Use Program 44-03 : Dial Analyze Extension Table to set the dial extension analyze table. Input Data Extension Table Area Number Dial Analysis Table Number 1-252 1. Dial Analysis Table Number 1-250: Related Prog.
  • Page 315 Program 44: ARS/F-Route Setup 44-03: Dial Analyze Extension Table Telephone Programming Instructions To enter data for Program 44-03 (Dial Analyze Extension Table): 1. Enter the programming mode. 2. Enter 44 03 44-03-01Exp-TBL1 001:Dial= 3. Enter the number of the item you want to program. 44-03-xx Exp- TBLx...
  • Page 316 Program 44: ARS/F-Route Setup 44-04: ARS/F-Route Selection for Time Schedule Description Use Program 44-04 : ARS/F-Route Selection for Time Schedule to assign each ARS/F-Route Selection number to an ARS/F-Route table number for each ARS/F-Route time mode. There are 8 time modes for ARS/F-Route Access.
  • Page 317 Program 44: ARS/F-Route Setup 44-05: ARS/F-Route Table Description Use Program 44-05 : ARS/F-Route Table to set the ARS/F-Route table. There are 4 kinds of order. If the higher priority trunk groups are busy, the next order group will be used. If a lower priority route is selected, the caller may be notified with a beep tone.
  • Page 318 Program 44: ARS/F-Route Setup 44-05: ARS/F-Route Table Telephone Programming Instructions To enter data for Program 44-05 (ARS/F-Route Table): 1. Enter the programming mode. 2. Enter 44 05 44-05-01FRout1 1:TRK Grp = 0 3. Enter the number of the item you want to program. 44-05-xxFRoutxxx xxxxx 4.
  • Page 319 Program 44: ARS/F-Route Setup 44-06: Additional Dial Table Description Use Program 44-06 : Additional Dial Table to set the additional dial table to add prior to the dialed ARS/F-Route number. Input Data Related Additional Dial Table Number Additional Dial Default Program 1-1000 No setting...
  • Page 320 Program 44: ARS/F-Route Setup 44-07: Gain Table for F-Route Access Description Use Program 44-07 : Gain Table for ARS/F-Route Access to set the PAD table. If an extension dials ARS/F- Route number; • The Extension Dial Gain Table is activated, which is assigned in Program 44-05. •...
  • Page 321 Program 44: ARS/F-Route Setup 44-07: Gain Table for F-Route Service Telephone Programming Instructions To enter data for Program 44-07(Gain Table for ARS/F-Route Access): 1. Enter the programming mode. 2. Enter 44 07 44-07-01 Gain1 INC Transmit 32 3. Enter the number of the item you want to program. 44-07-xx Gainxx xxxxx 4.
  • Page 322 Program 44: ARS/F-Route Setup 44-08: Time Schedule for ARS/F-Route Description Use Program 44-08 : Time Schedule for ARS/F-Route to define the daily pattern of the ARS/F-Route feature. ARS/F-Route has 10 time patterns. These patterns are used in Program 44-09 and 44-10. The daily pattern consists of 20 time settings.
  • Page 323 Program 44: ARS/F-Route Setup 44-08: Time Schedule for ARS/F-Route Telephone Programming Instructions To enter data for Program 44-08(Time Schedule for ARS/F-Route): 1. Enter the programming mode. 2. Enter 44 08 44-08-01TimPtn1 01:Start =00:00 3. Enter the number of the item you want to program. 44-08- xxTimPtnxx 4.
  • Page 324 Program 44: ARS/F-Route Setup 44-09: Weekly Schedule for ARS/F-Route Description Use Program 44-09 : Weekly Schedule for ARS/F-Route to define a weekly schedule for using ARS/F-Route. Input Data Day Number Schedule Pattern Number Default Related Program 1 : Sunday 2 : Monday 3 : Tuesday 4 : Wednesday 1-10...
  • Page 325 Program 44: ARS/F-Route Setup 44-10: Holiday Schedule for ARS/F-Route Description Use Program 44-10 : Holiday Schedule for ARS/F-Route to define a yearly schedule for ARS/F-Route. This schedule is used for setting special days such as national holidays. Input Data Date Schedule Pattern Number Default Related Program...
  • Page 326 Program 44: ARS/F-Route Setup For your Notes - Programming Manual...
  • Page 327 : Voice Mail Integration Program 45 45-01: Voice Mail Integration Options Description Use Program 45-01 :Voice Mail Integration Options to customize certain voice mail integration options. Input Data Related Prog. No. Item Input Data Default Program 45-01-01 Voice Mail Department Group Number 0-32 Assign which Extension (Department) (0 : No Voice Mail)
  • Page 328 Program 45: Voice Mail Integration 45-01: Voice Mail Integration Options Feature Cross Reference Voice Mail (In-skin) Telephone Programming Instructions To enter data for Program 45-01 (Voice mail Integration Options): 1. Enter the programming mode. 2. Enter 45 01 45-01-01   STG No.
  • Page 329 : Voice Mail Integration Program 45 45-02: NSL Option Setup Description Use Program 45-02 : NSL Option Setup to customize the NSL options for Voice Mail integration. Input Data Related Prog. No. Item Input Data Default Program 45-02-01 Send DTMF tone or 6KD Message 0 : Sending DTMF tone to SLT-VM port 1 : Sending 6KD Message to...
  • Page 330 Program 45: Voice Mail Integration 45-03 NSL Timer Setup Description Use Program 45-03 : NSL Timer Setup to customize the NSL timers for Voice Mail integration. Input Data Related Prog. No. Item Input Data Default Program 45-03-01 Retry Timer 0-64800 (sec.) 45-03-02 Polling Interval 0-64800 (sec.)
  • Page 331 Program 80 Basic Hardware Setup for System 80-01: Service Tone Setup Description Use Program 80-01 : Service Tone Setup to define up to 64 Service Tones. Each service tone is defined by the combination of 32 Basic Tones. Input Data Service Tone Number 01-64 Related...
  • Page 332 Program 80: Basic Hardware Setup for System 80-01: Service Tone Setup Default Service Repeat Unit Basic Tone Gain Level Service Tone Duration Tone No. Count Count (dB) No Tone 32(0 dB) 32(0 dB) Internal Dial Tone 32(0 dB) 32(0 dB) Special Dial Tone 32(0 dB) 32(0 dB)
  • Page 333 Program 80 Basic Hardware Setup for System 80-01: Service Tone Setup Default(Cont’d) Service Repeat Unit Basic Tone Gain Level Service Tone Duration Tone No. Count Count (dB) 38(+3 dB) 26(-3 dB) 38(+3 dB) Door Box Chime 3 26(-3 dB) 14(-9 dB) 32(0 dB) 38(+3 dB) 26(-3 dB)
  • Page 334 Program 80: Basic Hardware Setup for System 80-01: Service Tone Setup Default(Cont’d) Service Repeat Unit Basic Tone Gain Level Service Tone Duration Tone No. Count Count (dB) 32 (0dB) External Busy Tone 32 (0dB) 32(0 dB) 32(0 dB) Special Audible Ring-Busy 32(0 dB) 32(0 dB) Tone...
  • Page 335 Program 80 Basic Hardware Setup for System 80-01: Service Tone Setup Default(Cont’d) Service Repeat Unit Basic Tone Gain Level Service Tone Duration Tone No. Count Count (dB) Opening Chime tone 32 (0dB) 26 (-3dB) 32 (0dB) 26 (-3dB) 32 (0dB) 26 (-3dB) 32 (0dB) 26 (-3dB)
  • Page 336 Program 80: Basic Hardware Setup for System 80-01: Service Tone Setup Telephone Programming Instructions To enter data for Program 80-01(Service Tone Setup): 1. Enter the programming mode. 2. Enter 80 01 80-01-01 Tone1   Repeat Count 0 3. Enter the number of the item you want to program. 80-01-xx Tonexx xxxxx 4.
  • Page 337 Program 80 Basic Hardware Setup for System 80-05: Data Format for SMDR and System Reports Description Use Program 80-05 : Date Format for SMDR and System Reports to define the date format when printing out the SMDR, alarm report, system information report, etc. Input Data Data Format Default...
  • Page 338 Program 80: Basic Hardware Setup for System For your Notes - Programming Manual...
  • Page 339 Program 81: Basic Hardware Setup for Trunk 81-01: Analogue Trunk Initial Data Setup Description   Use Program 81-01 : Analogue Trunk Initial Data Setup to define the various basic timers for the Trunk Interface of 308M/308ME cards. Input Data Default Prog.
  • Page 340 Program 81: Basic Hardware Setup for Trunk 81-01: Analogue Trunk Initial Data Setup Input Data(Cont’d) Prog. No. Item Input Data Default Pulse Dial Break Time (10pps) 81-01-27 1-255 (8-2040mS) 13(104ms) Pulse Dial Make Time (10pps) 1-255 (8-2040mS) 81-01-28 7(56ms) Inter-digit Time (10pps) 81-01-29 1-255 (32-8160mS) 19(608ms)
  • Page 341 Program 81: Basic Hardware Setup for Trunk 81-02: Not Used Description   This command is currently not available. Programming Manual...
  • Page 342 Program 81: Basic Hardware Setup for Trunk 81-03: Not Used Description This command is currently not available. Programming Manual...
  • Page 343 Program 81: Basic Hardware Setup for Trunk 81-06: ISDN BRI Layer 3(T-Point) Timer Setup Description Use Program 81-06 : ISDN BRI Layer 3(T-Point) Timer Setup to define the various basic options for layer- 3 of ISDN BRI. Input Data Layer 3 Timer Type Number Related Prog.
  • Page 344 Program 81: Basic Hardware Setup for Trunk 81-06: ISDN BRI Layer 3(T-Point) Initial Data Setup Telephone Programming Instructions To enter data for Program 81-06 (ISDN BRI Layer 3(T-Point) Initial Data Setup): 1. Enter the programming mode. 2. Enter 81 06 81-06-01L3Timer1 T301 3.
  • Page 345 Program 81: Basic Hardware Setup for Trunk 81-07: CODEC Filter Setup for Analogue Trunk Ports Description Use Program 81-07 : CODEC Filter Setup for Analogue Trunk Ports to define the CODEC (QSLAC) Filter for each analogue trunk port(308M/308ME). Input Data Trunk Port Number 1-51 Related...
  • Page 346 Program 81: Basic Hardware Setup for Trunk 81-09: Analogue Trunk CODEC Filter Setup   Description Use Program 81-09 : Analogue Trunk CODEC Filter Setup to define the CODEC (QSLAC) Filter data for each analogue Trunk Interface(308M/308E card). This setting is applied when CODEC filter type4 (Specified Data) is set in PRG81-07.
  • Page 347 Program 81: Basic Hardware Setup for Trunk 81-09: Analogue Trunk CODEC Filter Setup Telephone Programming Instructions To enter data for Program 81-09 (Analogue Trunk CODEC Filter Setup): 1. Enter the programming mode. 2. Enter 81 09 81-09-01   B1 Filter(01)74 3.
  • Page 348 Program 81: Basic Hardware Setup for Trunk For your Notes - Programming Manual...
  • Page 349 Program 82: Basic Hardware Setup for Extension 82-01: Not Used Description   This command is currently not available. Programming Manual...
  • Page 350 Program 82 Basic Hardware Setup for Extension 82-03: Not Used Description This command is currently not available. Programming Manual...
  • Page 351 Program 82 Basic Hardware Setup for Extension 82-04: Analogue Station Initial Data Setup Description Use Program 82-04 : Analogue Station Initial Data Setup to define the various basic timers for the 308M/308ME Card. Input Data Related Default Prog. No. Item Input Data Program 82-04-01...
  • Page 352 Program 82 Basic Hardware Setup for Extension 82-04: Analogue Station Initial Data Setup Telephone Programming Instructions To enter data for Program 82-04 (Analogue Station Initial Data Setup): 1. Enter the programming mode. 2. Enter 82 04 82-04-01   Compand’n type 1 3.
  • Page 353 Program 82: Basic Hardware Setup for Extension 82-06: ISDN BRI Layer 3(S-Point) Timer Setup Description Use Program 82-06 : ISDN BRI Layer 3 (S-Point) Timer Setup to define the various basic timers for the layer 3 of ISDN BRI S-Point. Input Data Layer 3 Timer Type Number Related...
  • Page 354 Program 82: Basic Hardware Setup for Extension 82-06: ISDN BRI Layer 3(S-Point) Timer Setup Telephone Programming Instructions To enter data for Program 82-06 (ISDN BRI Layer 3(S-Point) Timer Setup): 1. Enter the programming mode. 2. Enter 82 06 82-06-01   T301 3.
  • Page 355 Program 82: Basic Hardware Setup for Extension 82-07: CODEC Filter Setup for Analogue Station Ports Description Use Program 82-07 : CODEC Filter Setup for Analogue Station Ports to define the CODEC (QSLAC) Filter for each analogue extension port. The CODEC filter operates according to a set value of PRG82-09 when CODEC filter type 4(Specified Data) is set in this setting.
  • Page 356 Program 82: Basic Hardware Setup for Extension 82-09: Analog Station CODEC Filter Data Setup Description Use Program 82-09: Analogue Station CODEC Filter Data Setup to define the Analogue Station CODEC (QSLAC) Filter data. This setting is applied when CODEC filter type 4 (Specified Data) is set in PRG82-07. Input Data Related Prog.
  • Page 357 Program 82 Basic Hardware Setup for Extension 82-09: Analog Station CODEC Filter Data Setup Telephone Programming Instructions To enter data for Program 82-09 (Analogue Station CODEC Filter Data Setup): 1. Enter the programming mode. 2. Enter 82 09 82-09-01   B1 Filter(01)42 3.
  • Page 358 Program 82: Basic Hardware Setup for Extension For your Notes - Programming Manual...
  • Page 359 Program 90: Maintenance Program 90-01: Installation Date Description Use Program 90-01 : Installation Date to define the installation date of system. Input Data Related Prog.No. Item Input Data Default Program 90-01-01 Year 00-99 00(No setting) 90-01-02 Month 01-12 00(No setting) 90-01-03 01-31 00(No setting)...
  • Page 360 Max. 10 characters 90-02-02 Password Up to 8 digits 0- Prohibited user 1- MF (Manufacturer level - for NEC-i use only) 90-02-03 User Level 2- IN (Installer level) 3- SA (System administrator level 1) 4- SB (System administrator level 2) Default User No.
  • Page 361 To enter data for Program 90-02 (Setting the Programming Password): 1. Enter the programming mode. 2. Enter 90 02 90-02-01 User1   Name -NEC-I 3. Enter the number of the item you want to program. 90-02-xx xxxxx 4. Enter data for the item you selected + HOLD.
  • Page 362 Program 90: Maintenance Program 90-03: Save Data Description Use Program 90-03 : Save Data to save the programmed data on the SRAM and Flash ROM to the Removable Compact Flash Memory. This program should be used after changing the programmed data. Input Data [Data Save] Dial 1 and HOLD key (Press only HOLD key for cancel)
  • Page 363 Program 90: Maintenance Program 90-04: Load Data Description Use Program 90-04 : Load Data to load the system data from the inserted Compact Flash Memory to the SRAM and Flash ROM in the system. Input Data [Data Load] : Dial 1 and HOLD key (Press only HOLD key for cancel) Conditions None Feature Cross Reference...
  • Page 364 Program 90: Maintenance Program 90-05: Slot Control Description Use Program 90-05 : Slot Control to close (turn off) or delete (uninstall) circuit boards (slots 1-18). Delete allows you to completely uninstall the PCB. You might want to do this if you want to remove a PCB and plug it into a different slot - and still retain the port assignments.
  • Page 365 Program 90: Maintenance Program 90-06: Trunk Control Description Use Program 90-06 : Trunk Control is used for the trunk maintenance. Busy Out lets you block a PCB from placing outgoing calls. Once busied out, none of the ports on the PCB can be used for new calls. Existing calls, however, are not torn down.
  • Page 366 Program 90: Maintenance Program 90-07: Extension Control Description Use Program 90-07 : Extension Control is used for the extension maintenance. Input Data 1 : Hardware Reset Menu Number 2 : Software Reset Extension Number Up to 4 digits Conditions None Feature Cross Reference None Telephone Programming Instructions...
  • Page 367 Program 90: Maintenance Program 90-08: System Reset Description Use Program 90-08 : System Reset is used to perform a system reset. Input Data [System-Reset] : Dial 1 and HOLD key (Press only HOLD key for cancel) Conditions None Feature Cross Reference None Telephone Programming Instructions To enter data for Program 90-08 (System Reset):...
  • Page 368 Program 90: Maintenance Program 90-09: Automatic System Reset Time Description Use Program 90-09 : Automatic System Reset Time to define the time the system will automatically reset. Input Data Related Prog.No. Item Input Data Default Program 90-09-01 Month 00-12(Note 1) 90-09-02 00-31(Note 2) 90-09-03...
  • Page 369 Program 90: Maintenance Program 90-10: System Alarm Setup Description Use Program 90-10 : System Alarm Setup to assign a status to system alarms. You can designate an alarm as Major or Minor. This program also assigns whether or not the alarm is displayed to a key telephone and whether or not the alarm information is reported to the pre-defined destination.
  • Page 370 Program 90: Maintenance Program 90-10: System Alarm Setup Default(Cont’d) Alarm Type Report Note Is Used To Advise of…….. Action ISDN Link Error CTI Link Error ACD-MIS Link Error TMR Link Error EXIFU-LAN Link Error -Not Used- TRM output Buffer Full SMDR output Check the printer for the 2(MIN)
  • Page 371 Program 90: Maintenance Program 90-11: System Alarm Report Setup Description Use Program 90-11 : System Alarm Report to define the details of the system alarm report. Input Data Prog.No. Item Input Data Default System Alarm Display Telephone 90-11-01 Assign the display KTS port that should receive Up to 4 digits No setting system alarms.
  • Page 372 Program 90: Maintenance Program 90-11: System Alarm Report Setup Telephone Programming Instructions To enter data for Program 90-11 (System Alarm Report): 1. Enter the programming mode. 2. Enter 90 11 90-11-01   ALM Disp.TEL 3. Enter the number of the item you want to program. 90-11-xx xxxxx 4.
  • Page 373 Program 90: Maintenance Program 90-12: System Alarm Output Description Use Program 90-12 : System Alarm Output to set the options for the alarm report. This program has separate menu options. Define the output port to be used as the output for system alarm report and set the system alarm options.
  • Page 374 Program 90: Maintenance Program 90-13: System Information Output Description Use Program 90-13 : System Information Output to define the output port to be used as the system information output. The baud rate for the COM port should be set in Program 10-21-02. Input Data Prog.No.
  • Page 375 Program 90: Maintenance Program 90-16: Main Software Information Description Use Program 90-16 : Main Software Information to display the main software information on the CPU. This Version Number information can also be viewed outside of system programming by pressing OPAC Key and Dial 3 then the on any display keyset.
  • Page 376 Program 90: Maintenance Program 90-17: Firmware Information Description Use Program 90-17 : Firmware Information to display the firmware information on the 308M and other PCBs. Input Data Prog.No. Item Data Component 90-17-01 DSP Firmware Version Number 00.00.00.00 – 15.15.15.15 BCD Code (2 Byte) 90-17-02 DSPDB Firmware Version Number 00.00.00.00 –...
  • Page 377 Program 90: Maintenance Program 90-19: Dial Block Release Description When the extension number is entered in Program 90-19 : Dial Block Release, the extension will be released from the Dial Block restriction. Input Data Extension Number Up to 4 digits Input Data [CLR Dial Block] : Dial 1 and press HOLD key (Press only HOLD key for cancel)
  • Page 378 Program 90: Maintenance Program 90-20: Traffic Report Data Setup Description Use Program 90-20 : Traffic Report Data Setup to define the details of the traffic report. Input Data Prog.No. Item Input Data Default 0 : Not measured 90-20-01 Call Traffic Output 1 : Measured 90-20-02 -Not Used-...
  • Page 379 Program 90: Maintenance Program 90-21: Traffic Report Output Description Use Program 90-21 : Traffic Report Output to define the output port to be used as the traffic report output. Input Data Prog.No. Item Input Data Default 0 : No setting 90-21-01 Output port type 1 : COM port(EXIFU)
  • Page 380 Program 90: Maintenance Program 90-23: Not Used Description This command is currently not used. Programming Manual...
  • Page 381 Program 90: Maintenance Program 90-24: System Alarm Report Notification Time Setup Description Use Program 90-24 : System Alarm Report Notification Time Setup to set up when the alarm report will print.. Input Data Related Prog.No. Item Input Data Default Program 90-24-01 Month 00-12(0 : disabled)
  • Page 382 Program 90: Maintenance Program 90-25: System Alarm Report CC Mail Setup Description Use Program 90-25 : System Alarm Report CC Mail Setup to define the mail address to receive the system alarm report CC Mail setup. Input Data CC Number Prog.No.
  • Page 383 Program 90: Maintenance Program 90-26: System Data Programming Level Assignment Description Use Program 90-26 : System Data Programming Level Setup to define the programming access level of each command. Input Data Program Number 1001-9201 Prog.No. Item Input Data Default 1 : MF(Manufacturing Level) Refer to each 2 : IN(Installer Level) header of...
  • Page 384 Program 90: Maintenance Program 90-30: Not Used Description This command is currently not used. Programming Manual...
  • Page 385 Program92: Copy Program 92-01: Copy Command Description Use Program 92-01 : Copy Program to copy the data for one program to another keyset, port, group, etc. Refer to the following charts to see which programs which can be copied. Input Data Program Number xx-xx Prog.No.
  • Page 386 Program 92: Copy Program 92-01: Copy Command 2. Trunk Group Base Prog.No. Program Name Note 35-03 SMDR Port Assignment for Trunk Group 3. Extension Base Prog.No. Program Name Note Copy all data except extension name(15-01-01) Extension Basic Data Setup (include Virtual 15-01 Extension) 15-02...
  • Page 387 Program92: Copy Program 92-01: Copy Command Feature Cross Reference None Telephone Programming Instructions To enter data for Program 92-01 (Copy Command): 1. Enter the programming mode. 2. Enter92 01 92-01-01 Copy Func. 3. Enter the number of the item you want to program. 92-01-xx xxxxx 4.
  • Page 388 Program 92: Copy Program 92-02: Delete All Extension Number Description Use Program 92-02 : Delete All Extension Number to delete all extension numbers(PRG11-02,PRG11-04), However, the extension number of first port is not deleted. Input Data [Ext No. Del YES:1] Press Dial 1 + HOLD Key. (Only Press HOLD key is canceled.) Conditions None...
  • Page 389 - For Your Notes -...
  • Page 390 NEC Infrontia Asia Pacific Sdn. Bhd. 24, Jalan Juruhebah U1/50, Temasya Industrial Park Phase 2, Seksyen U1 Glenmarie, 40150 Shah Alam, Selangor Darul Ehsan, Malaysia TEL : +60-3-5569-5888 FAX : +60-3-5569-3898 http://www.necinfrontia-ap.com...

Table of Contents