B&R Automation PC 3100 User Manual page 166

Software
5) With a multifunction device, all functions within the device are monitored.
For the root port, the error occurs within the root complex.
6) Generates a system error if an error of this category is reported by a root port or device on a root port.
7.1.6.2.9.2 SATA and RST configuration
BIOS parameter
SATA controller(s)
1)
SATA mode selection
SATA test mode
RAID device ID
Software feature mask configuration
Aggressive LPM support
Serial ATA port n
Software preserve
Port n
Hot plug
Configured as eSATA
Spin up device
SATA device type
Topology
SATA port n DevSlp
DITO configuration
DITO value
DM value
Table 111: Advanced - PCH-IO configuration - SATA and RST configuration
1) SATA controller(s) must be enabled to be able to make additional configurations.
2) This submenu can only be configured if "SATA test mode" is enabled.
3) n corresponds to the available SATA ports that are indexed from 0 to n-1.
Software feature mask configuration
BIOS parameter
HDD unlock
LED locate
Use RST legacy OROM
RAID0
RAID1
RAID10
RAID5
Intel Rapid Recovery technology
OROM UI and banner
IRRT only on eSATA
Table 112: Advanced - PCH-IO configuration - SATA and RST configuration - Software feature mask configuration
166
Setting options Description
Disabled Disables/Enables the SATA controller
Enabled
AHCI Select SATA mode AHCI (not RAID) or Optane (or RAID)
See
Intel RST premium
with Intel Optane
Disabled Disables/Enables the test function
This is only used for control measurements.
Enabled
Alternate Selects the RAID device ID mode
Client
Enter Opens submenu
2)
Disabled Disables/Enables Aggressive Link Power Management
The host controller can change to a low-power state in the idle phase of the SATA device.
Enabled
- Displays the name and capacity of the SATA device
- Displays support for the software preserve
Disabled Disables/Enables SATA port n
Enabled
Disabled Disables/Enables hot plugging
Enabled
- Displays hot plugging support of the device on the SATA port
Disables/Enables spin up for the connected device on the SATA port
Disabled
Enabled
Hard disk drive Defines the SATA device type as HDD or SSD
Solid-state drive
Unknown Defines the SATA topology
ISATA
Direct connect
Default for port 0 and 1
Flex
M2
Default for port 2
Disabled Disables/Enables for the device on port n
Enabled
Disabled Disables/Enables device sleep idle timeout
Enabled
INT Defines the DITO value [ms]
Default: 625 Range: 0 to 1023
INT Defines the DITO multiplier
Default: 15 Range: 0 to 15
Setting options Description
Disabled Disables/Enables HDD unlock
The HDD can be locked in the operating system by a password.
Enabled
Disabled Disables/Enables LED locate
Indicates that LED/SGPIO hardware is connected and pingable.
Enabled
Disabled Disables/Enables rapid storage technology legacy option ROM for active CSM
Enabled
Disabled Disables/Enables RAID0
Enabled
Disabled Disables/Enables RAID1
Enabled
Disabled Disables/Enables RAID10
Enabled
Disabled Disables/Enables RAID5
Enabled
Disabled Disables/Enables Intel Rapid Recovery Technology (IRRT)
Enabled
Disabled Disables/Enables OROM UI
If OROM UI is disabled, no information is displayed as long as all storage media are in
Enabled
normal operation.
Disabled Disables/Enables IRRT only on eSATA
Enable to make internal and eSATA drives available for IRRT storage media.
Enabled
"RAID configuration" on page 180.
"Software feature mask configuration" on page 166
Automation PC 3100 User's manual V 2.10
1)