Page 1
Elektronik Ges.m.b.H. shall not be liable in the event of incidental or consequential damages in connection with or resulting from the furnishing, performance, or use of these products. The software names, hardware names, and trademarks used in this manual are registered by the respective companies. Panel PC 800 User's Manual V 1.00...
Chapter 2: Technical data .............. 33 1. Introduction ......................... 33 1.1 Features ........................34 1.2 System components / Configuration ................35 1.2.1 Configuration - Basic system .................. 35 1.2.2 Configuration - Optional components ..............36 Panel PC 800 User's Manual V 1.00...
Page 8
3.5 Expansion ........................81 3.5.1 Technical data ......................82 3.5.2 Dimensions - 5PC803.SX01-00 ................82 3.5.3 Dimensions - 5PC803.SX02-00 ................83 3.5.4 Slot for bus units ..................... 84 3.5.5 Slide-in slot 1 ......................85 Panel PC 800 User's Manual V 1.00...
Page 9
4.3.1 Basic system requirements ................... 139 4.3.2 Link modules ......................140 4.3.3 Cables ........................140 4.3.4 BIOS settings ......................141 4.4 One Automation Panel 800 via SDL ................142 4.4.1 Basic system requirements ................... 142 Panel PC 800 User's Manual V 1.00...
Page 10
1. BIOS options ........................167 1.1 General information ..................... 167 1.2 BIOS setup and boot procedure .................. 167 1.2.1 BIOS setup keys ....................168 1.3 Main ..........................170 1.4 Advanced ........................171 1.4.1 ACPI configuration ....................173 Panel PC 800 User's Manual V 1.00...
Page 11
2.4.1 Requirements ......................243 2.4.2 Procedure ......................243 2.4.3 Where do I get MS-DOS? ..................244 2.5 Creating a bootable CompactFlash card for B&R upgrade files ........245 2.5.1 Requirements ......................245 2.5.2 Procedure ......................245 Panel PC 800 User's Manual V 1.00...
Page 12
5.3 Installation ........................252 5.4 Drivers ......................... 252 5.4.1 Touch screen driver ....................252 6. Panel PC 800 with Windows Embedded Standard 2009 ..........253 6.1 General information ..................... 253 6.2 Features with WES2009 (Windows Embedded Standard 2009) ......... 254 6.3 Installation ........................
Page 13
4. DVI - monitor adapter 5AC900.1000-00 ................298 4.1 Order data ........................298 5. USB interface cover (attached) ..................299 5.1 Order data ........................299 6. Uninterruptible power supply .................... 300 6.1 Features ........................301 Panel PC 800 User's Manual V 1.00...
Page 14
13.3.1 Order data ......................333 13.3.2 Technical data ..................... 334 13.3.3 Flex radius specification ..................334 13.3.4 Cable specifications .................... 335 13.4 SDL flex cable 5CASDL.0xxx-03 ................336 13.4.1 Order data ......................336 Panel PC 800 User's Manual V 1.00...
However, any newer versions of the User's Manual can always be downloaded in electronic form (pdf) from the B&R homepage www.br- automation.com. 1. Manual history Version Date Change 0.10 Preliminary 2009-11-10 - First version Table 1: Manual history Panel PC 800 User's Manual V 1.00...
Page 18
- Section 1.2.4 "Spacing for air circulation.", on page 132 updated. - Section 1.2 "Mounting orientation", on page 129 updated. - Section 6 "Panel PC 800 with Windows Embedded Standard 2009", on page 253 updated. - Section 4 "Connection examples", on page 135 updated.
Components can only be touched on the small sides or on the front plate. • Components should always be stored in a suitable medium (ESD packaging, conductive foam, etc.). Metallic surfaces are not suitable storage surfaces! Panel PC 800 User's Manual V 1.00...
2.4 Transport and storage During transport and storage, devices must be protected from excessive stress (mechanical load, temperature, humidity, aggressive atmospheres, etc.). Panel PC 800 User's Manual V 1.00...
Automation Panel or Power Panel are protected on the front side. The rear side of all devices must be protected from dust and humidity and must be cleaned at suitable intervals. Panel PC 800 User's Manual V 1.00...
Operating and monitoring devices Uninterruptible power supply Cables Cardboard box / paper packaging Paper / cardboard recycling Plastic packaging Plastic recycling Table 2: Environmentally-friendly separation of materials Disposal must comply with the respective legal regulations. Panel PC 800 User's Manual V 1.00...
Disregarding the safety regulations and guidelines can result in injury or damage to material. Information: Important information for preventing errors. Table 3: Organization of safety notices 4. Directives European dimension standards apply to all dimensions (e.g. dimension diagrams, etc.). Panel PC 800 User's Manual V 1.00...
See page 79 PPC800 heat sink for CPU board with Dual Core processor T7400. 5AC803.HS00-02 Panel PC 800 heat sink 945GME N270 See page 79 PPC800 heat sink for CPU boards with Atom N270 processor and Chipset 945GME. Table 6: Model numbers - Heat sinks 5.4 Main memory...
PCI RAID controller + 2 x 160 GB SATA hard disks; requires a free PCI slot. 5ACPCI.RAIC-04 Replacement SATA-HDD 160GB See page 121 Hard disk 160 GB SATA, replacement part for 5ACPCI.RAIC-03 Table 12: Model numbers - Drives Panel PC 800 User's Manual V 1.00...
Connection cable between add-on UPS module and UPS battery unit, length 0.5 meters 5CAUPS.0030-00 3 m APC620 UPS cable See page 300 Connection cable between add-on UPS module and UPS battery unit, length 3 meters Table 16: Model numbers - UPS module + accessories Panel PC 800 User's Manual V 1.00...
SDL cable for fixed and flexible type of layout; length: 20 m 5CASDL.0250-00 SDL cable 25 m See page 330 SDL cable for a fixed type of layout; length: 25 m Table 20: Model numbers - Cables Panel PC 800 User's Manual V 1.00...
USB port cap IP65 M20 /4 See page 299 Front-side USB port cap (attached) knurled, tall, slotted. 1A4300.LZ1U B&R Automation Studio 3.0 USB dongle See page 323 Dongle for using AR010. Table 21: Model numbers - Other items Panel PC 800 User's Manual V 1.00...
Order Microsoft OEM Windows Embedded Standard 2009, English; for PPC800 with CPU See page 253 boards 5PC800.B945-00, 5PC800.B945-01, 5PC800.B945-02, 5PC800.B945-03, 5PC800.B945-04, 5PC800.B945-05; CompactFlash separately (at least 1 GB). Table 22: Model numbers - Software Panel PC 800 User's Manual V 1.00...
Page 32
General information • Model numbers Panel PC 800 User's Manual V 1.00...
Chapter 2 • Technical data 1. Introduction The Panel PC 800 covers a wide performance range from efficient Intel Atom N270 processors to Core2 Duo processors for applications with the highest performance requirements. Brilliant 15" XGA and 19" SXGA touch screen displays provide a simple and intuitive user interface. The flexibility was raised to a new level when designing the PPC800.
5AC803.HS00-00 Main memory 1 or 2 can be selected (max. 3 GB can be used) 5MMDDR.0512-01 - 512 MB 5MMDDR.1024-01 - 1 GB 5MMDDR.2048-01 - 2 GB Figure 1: Configuration - Basic system Panel PC 800 User's Manual V 1.00...
If both options are used, then a PCIec plug-in card and a slide-in compact drive can also be operated in a device. A fan kit may be necessary for certain system configurations. Figure 2: Configuration - Optional components Panel PC 800 User's Manual V 1.00...
(serial interfaces, slide-in drives, USB interfaces, audio outputs) • Maximum system extension and power consumption What must be considered when determining the maximum ambient temperature? • Operating the entire device with or without fan kit Panel PC 800 User's Manual V 1.00...
5ACPCI.RAIC-03 (24 hours / default) 5ACPCI.RAIC-04 (24 hours / default) 1) Only possible with a CompactFlash card ( 5CFCRD.xxxx-04 or 5CFCRD.xxxx-03) from B&R Figure 3: Ambient temperatures with and without fan kit - CPU boards 5PC800.B945-0x Panel PC 800 User's Manual V 1.00...
2.1.2 Minimum ambient temperature For systems containing one of the following components, the minimum ambient temperature is +5°C: 5AC801.DVDS-00, 5AC801.DVRS-00. If none of these components are used, then the minimum ambient temperature is 0°C. Panel PC 800 User's Manual V 1.00...
(e.g. HDD thermometer - freeware) in Microsoft Windows XP/Embedded and Windows Embedded Standard 2009. 1) The measured temperature is a guideline for the immediate ambient temperature, but can be influenced by neighboring components. Panel PC 800 User's Manual V 1.00...
The listed specifications correspond to the humidity at an ambient temperature of 30°C. More detailed information about the specific temperature-dependent humidity values can be found in the technical data for the individual components. Panel PC 800 User's Manual V 1.00...
An additional DC/DC converter generates +12 V. The optional Add-on UPS (with battery unit) is supplied with 15 V and provides an uninterrupted power supply from the 15 V bus during power failures. Panel PC 800 User's Manual V 1.00...
Figure 6: Power calculation for 5PC820.1505-00 Information: The PCIec card must not consume more than a total of 4 W (12V/5V/3V3)! Panel PC 800 User's Manual V 1.00...
Figure 7: Power calculation for 5PC820.1906-00 Information: The PCIec card must not consume more than a total of 4 W (12V/5V/3V3)! Panel PC 800 User's Manual V 1.00...
This serial number represents all of the components built into the system (model number, name, revision, serial number, delivery date and duration of warranty). Serial number sticker Figure 9: Serial number sticker (back) Panel PC 800 User's Manual V 1.00...
Page 47
The search provides you with a detailed list of the individual components. Enter serial number e.g. AF210168454 List of installed components according to serial number search Figure 10: Example of serial number search Panel PC 800 User's Manual V 1.00...
3-pin, male Description Supply voltage + 24 VDC Functional ground Accessories 0TB103.9 Plug 24 V 5.08 3p screw clamps 0TB103.91 Plug 24 V 5.08 3p cage clamps Table 24: Supply voltage connection + 24VDC Panel PC 800 User's Manual V 1.00...
Page 49
The M4 self-locking nut can be used, for example, to fasten a copper strip that is built into the PPC800 at a central grounding point in the switching cabinet or system. The largest possible conductor cross section should be used (at least 2.5 mm²). Panel PC 800 User's Manual V 1.00...
Table 26: Pin assignments - COM1 1) The interfaces, etc. available on the device or module were numbered accordingly for easy identification. This numbering can differ from the numbering used by the particular operating system. Panel PC 800 User's Manual V 1.00...
A special driver is necessary for operating the Realtek Ethernet controllers RTL8111B/C. The necessary software can be downloaded from the download area on the B&R homepage (www.br-automation.com). Information: Required drivers can only be downloaded from the B&R homepage, not from manufacturers' pages. Panel PC 800 User's Manual V 1.00...
A special driver is necessary for operating the Intel Ethernet controller 82574. The necessary software can be downloaded from the download area on the B&R homepage (www.br- automation.com). Information: Required drivers can only be downloaded from the B&R homepage, not from manufacturers' pages. Panel PC 800 User's Manual V 1.00...
1) The interfaces, etc. available on the device or module were numbered accordingly for easy identification. This numbering can differ from the numbering used by the particular operating system. 2) For safety, every USB port is equipped with a maintenance free "USB current-limiting circuit breaker" (max. 500 mA or 1 A). Panel PC 800 User's Manual V 1.00...
Page 55
1) The interfaces, etc. available on the device or module were numbered accordingly for easy identification. This numbering can differ from the numbering used by the particular operating system. 2) For safety, the USB port is equipped with a maintenance free "USB current-limiting circuit breaker" (max. 1 A) Panel PC 800 User's Manual V 1.00...
A special driver is necessary for operating the audio controller. The necessary software can be downloaded from the download area on the B&R homepage (www.br-automation.com). Information: Required drivers can only be downloaded from the B&R homepage, not from manufacturers' pages. Panel PC 800 User's Manual V 1.00...
NTC (for battery temperature measurement Table 32: Add-on UPS slot (with and without mounted UPS) For more on the UPS module, see chapter 6 "Accessories", section 6 "Uninterruptible power supply", on page 300. Panel PC 800 User's Manual V 1.00...
Application running Green Application is not running Table 33: Data - status LEDs 1) Only lit when add-on UPS module is installed. Panel PC 800 User's Manual V 1.00...
The position of the CMOS profile switch is is displayed in the BIOS setup pages and in the B&R ADI Control Center, among other places. Panel PC 800 User's Manual V 1.00...
The PPC800 is restarted (cold restart). The MTCX processor is not reset when the reset button is pressed. Table 36: Reset button Warning! A system reset can cause data to be lost! Panel PC 800 User's Manual V 1.00...
Data buffering is guaranteed Data buffering is guaranteed for approx. another 500 hours from the point in time that the battery capacity is determined to be BAD (insufficient). Table 38: Meaning of battery status Panel PC 800 User's Manual V 1.00...
The option 5AC803.BC02-00 is required for the use of slide-in compact drives. Information: The SATA I interface allows data carriers to be exchanged during operation (hot- plug). To utilize this capability, it must be supported by the operating system. Panel PC 800 User's Manual V 1.00...
Only B&R PCIec cards that were specially designed for the Automation PC 820 and Panel PC 800 can be used. More information can be found in section 3.8 "Plug-in cards", on page 89. Panel PC 800 User's Manual V 1.00...
CompactFlash slot CF2 COM1 RS232 CompactFlash slot CF1 HDA Sound Reset button MIC, Line IN, Line OUT Power button Battery LED for: Power, CMOS profile switch Link1, Run, HDD Figure 13: Rear view 5PC820.1505-00 Panel PC 800 User's Manual V 1.00...
Page 67
Yes, accessible from the outside Lifespan 2½ years Interfaces Serial interfaces Type RS232, modem-capable, not electrically isolated Amount UART 16550-compatible, 16-byte FIFO Transfer rate Max. 115 kBaud Connection 9-pin D-SUB Table 43: Technical data - 5PC820.1505-00 Panel PC 800 User's Manual V 1.00...
Page 68
Direction R = 60° / direction L = 60° Vertical Direction U = 45°/ direction D = 55° Background lighting Brightness 250 cd/m² Half-brightness time 50,000 hours Table 43: Technical data - 5PC820.1505-00 (cont.) Panel PC 800 User's Manual V 1.00...
Page 69
IP20 back side IP65 / NEMA 250 type 4X, dust and sprayed water protection (front side) Altitude -300 to 3000 m above sea level Drop height Table 43: Technical data - 5PC820.1505-00 (cont.) Panel PC 800 User's Manual V 1.00...
Page 70
The screw heads with a height of 2.5 mm must also be accounted for in the depth measurement. Information: The value depends on the expansion being used! Model number Values in mm without expansion 81.7 5AC803.SX01-00 5AC803.SX02-00 Figure 14: Dimensions - 5PC820.1505-00 Panel PC 800 User's Manual V 1.00...
Page 71
Technical data • Individual components Cutout installation The Panel PC 800 with preassembled mounting blocks is installed e.g. in a housing cutout. A cutout that corresponds to the following drawing must be made. Outer contours (Panel PC 800) Cut-out Cut-out dimensions 415 ±0.5 mm x 312 ±0.5 mm suitable for 5PC820.1505-00...
PPC800 must be sent for repair. Removal of the mounting screws, which can be determined by a broken seal, voids all warranty. During operation, surface temperatures of the heat sink may reach 70°C (warning "hot surface"). Panel PC 800 User's Manual V 1.00...
Page 73
Type A Current load Max. 500 mA or 1 A per connection Sound HDA Sound Inputs Microphone, Line in Outputs Line out CompactFlash slot Type Type I Amount Table 44: Technical data - 5PC820.1906-00 Panel PC 800 User's Manual V 1.00...
Page 74
24 VDC ±25% Rated current Starting current Typ. 10 A, max. 50 A for <300µs Power consumption Component-dependent, see "Power calculation with 5PC820.1906-00", on page 44 Electrical isolation Table 44: Technical data - 5PC820.1906-00 (cont.) Panel PC 800 User's Manual V 1.00...
Page 75
2) Touch screen drivers can be downloaded from the download area on the B&R homepage (www.br-automation.com). 3) At 25°C ambient temperature. Reducing the brightness by 50% can result in an approximate 50% increase of the half-brightness time. Panel PC 800 User's Manual V 1.00...
Page 76
The screw heads with a height of 2.5 mm must also be accounted for in the depth measurement. Information: The value depends on the expansion being used! Model numbers Values in mm without expansion 81.7 5AC803.SX01-00 5AC803.SX02-00 Figure 18: Dimensions - 5PC820.1906-00 Panel PC 800 User's Manual V 1.00...
Page 77
Technical data • Individual components Cutout installation The Panel PC 800 with preassembled mounting blocks is installed e.g. in a housing cutout. A cutout that corresponds to the following drawing must be made. Outer contours (Panel PC 800) 412.5 Cut-out Cut-out dimensions 510 ±0.5 mm x 404 ±0.5 mm suitable for...
Power management ACPI 2.0, S3 Support (suspend to RAM) Table 45: Technical data - CPU boards 1) At max. specified ambient temperature: typ. 58 ppm (5 seconds) - worst-case 220 ppm (19 seconds). Panel PC 800 User's Manual V 1.00...
5PC800.B945-10 5PC800.B945-11 5PC800.B945-12 5PC800.B945-13 Item Aluminum, black-coated with copper heat pipes Outer dimensions Width 143 mm Height 183.5 mm Depth 60 mm Weight Approx. 1.2 kg Table 46: Technical data - Heat sink Panel PC 800 User's Manual V 1.00...
200 Pin SO-DIMM Organization 64M x 64-bit 128M x 64-bit 256M x 64-bit Table 47: Technical data - Main memory Information: A main memory module can only be replaced at the B&R plant. Panel PC 800 User's Manual V 1.00...
6 to 30 mm over 30 to 120 mm ± 0,3 mm ± 0,5 mm over 120 to 400 ± 0,8 mm over 400 to 1000 Figure 25: Dimensions - Expansion 5PC803.SX01-00 Panel PC 800 User's Manual V 1.00...
6 to 30 mm ± 0,3 mm over 30 to 120 mm ± 0,5 mm over 120 to 400 ± 0,8 mm over 400 to 1000 Figure 26: Dimensions - Expansion 5PC803.SX02-00 Panel PC 800 User's Manual V 1.00...
177.7 All values in mm 17.4 25.8 Figure 27: Dimensions - Standard half-size PCI card 167.65 11.65 3.65 All values in mm 49.65 57.15 59.05 Figure 28: Dimensions - Standard half-size PCIe card Panel PC 800 User's Manual V 1.00...
APC810 and PPC800 slide-in DVD Table 49: Slide-in slot 1 Information: The SATA I interface allows data carriers to be exchanged during operation (hot- plug). To utilize this capability, it must be supported by the operating system. Panel PC 800 User's Manual V 1.00...
PCI bus type 32-bit 32-bit 32-bit Bus speed 33 MHz 33 MHz 33 MHz PCI Express Amount Default 1.0a 1.0a Bus speed x1 (250 MB/s) x1 (250 MB/s) Table 50: Technical data - Bus units Panel PC 800 User's Manual V 1.00...
It is also possible to select both options so that a PCIec plug-in card and a slide-in compact drive can be operated in the PC 800. 5PC803.BC01-00 5PC803.BC02-00 Figure 31: Options Information: Options are only available factory-installed. Panel PC 800 User's Manual V 1.00...
Only B&R PCIec cards that were specially designed for the Automation PC 820 and Panel PC 800 can be used. Information: The option 5AC803.BC01-00 is required for the use of PCIec plug-in cards. Panel PC 800 User's Manual V 1.00...
The following characteristics, features, and limit values only apply to this individual component and can deviate from those specified for the entire device. For the entire device in which this individual component is used, refer to the data given specifically for the entire device. Panel PC 800 User's Manual V 1.00...
Page 91
A special driver is necessary for operating the Intel Ethernet controller 82574. The necessary drivers can be downloaded from the download area on the B&R homepage (www.br- automation.com). Information: Required drivers can only be downloaded from the B&R homepage, not from manufacturers' pages. Panel PC 800 User's Manual V 1.00...
(orange) (green / orange) Green / red see Status / Error LED Link LED Blinking Yellow Link Activity (blinking) (POWERLINK (Data transfer in network progress) connection available) Table 52: POWERLINK card 2-port connection Panel PC 800 User's Manual V 1.00...
Page 93
No output data is produced and no input data is received. Only the appropriate command from the manager can enter or leave this state. Table 54: Status / Error LED as status LED - POWERLINK card 2-port operating mode Panel PC 800 User's Manual V 1.00...
Page 94
The one-digit card number ($1 – $F) is configured using the card number switch. This number is used to identify the module. Card number switch Figure 35: POWERLINK card 2-port node number switch Panel PC 800 User's Manual V 1.00...
Features 5AC801.HDDI-00 Manufacturer's product ID Seagate ST940817SM Formatted capacity 40 GB Number of heads Number of sectors (user) 78,140,160 Table 56: Technical data - Add-on hard disk - 5AC801.HDDI-00 Panel PC 800 User's Manual V 1.00...
Page 96
2) Temperature values for 305 meter altitude. The temperature specification must be reduced linearly by 1°C every 305 meters. The temperature increase and decrease can be a maximum of 20°C per hour. 3) Humidity gradient: Maximum 15% per hour. Panel PC 800 User's Manual V 1.00...
Page 97
Figure 37: Temperature humidity diagram - 5AC801.HDDI-00 Temperature values for 305 meter altitude. The temperature specification must be reduced linearly by 1°C every 305 meters. The temperature increase and decrease can be a maximum of 20°C per hour. Panel PC 800 User's Manual V 1.00...
Manufacturer's product ID Fujitsu MHY2160BH-ESW Formatted capacity 160 GB Number of heads Number of sectors (user) 312,581,808 Bytes per sector Revolution speed 5400 rpm Table 57: Technical data - Slide-in compact HDD - 5AC801.HDDI-02 Panel PC 800 User's Manual V 1.00...
Page 99
2) Temperature values for 305 meter altitude. The temperature specification must be reduced linearly by 1°C every 305 meters. The temperature increase and decrease can be a maximum of 20°C per hour. 3) Humidity gradient: Maximum 15% per hour. Panel PC 800 User's Manual V 1.00...
Page 100
Figure 39: Temperature humidity diagram - 5AC801.HDDI-02 Temperature values for 305 meter altitude. The temperature specification must be reduced linearly by 1°C every 305 meters. The temperature increase and decrease can be a maximum of 20°C per hour. Panel PC 800 User's Manual V 1.00...
The following characteristics, features, and limit values only apply to this individual component and can deviate from those specified for the entire device. For the entire device in which this individual component is used, refer to the data given specifically for the entire device. Panel PC 800 User's Manual V 1.00...
Page 102
2.17 g at 7 - 800 Hz Bearings 3.13 g at 10 - 500 Hz Transport 3.13 g at 10 - 500 Hz Table 58: Technical data - Slide-in compact SSD - 5AC801.SSDI-00 Panel PC 800 User's Manual V 1.00...
Page 103
Table 58: Technical data - Slide-in compact SSD - 5AC801.SSDI-00 (cont.) 1) IOPS: Random read and write input/output operations per second Temperature humidity diagram - Operation and storage Storage Operation Transport Temperature [°C] Figure 41: Temperature humidity diagram - 5AC801.SSDI-00 Panel PC 800 User's Manual V 1.00...
Page 104
8192 Transfer size [kb] 5AC810.SSDI-00 5AC810.HDDI-00 Figure 42: ATTO disk benchmark v2.34 - cyclic read 1024 2048 4096 8192 Transfer size [kb] 5AC810.SSDI-00 5AC810.HDDI-00 Figure 43: ATTO disk benchmark v2.34 - cyclic write Panel PC 800 User's Manual V 1.00...
Figure 44: Hard disk adapter (slide-in compact) 5AC801.ADAS-00 Technical data Mechanical characteristics 5AC801.ADAS-00 Outer dimensions Height 172.5 mm Width 22 mm Depth 150 mm Weight 328 g Table 59: Technical data - Slide-in HDD adapter - 5AC801.ADAS-00 Panel PC 800 User's Manual V 1.00...
Features 5AC801.HDDS-00 Manufacturer's product ID Seagate ST940817SM Formatted capacity 40 GB Number of heads Number of sectors (user) 78,140,160 Bytes per sector Table 60: Technical data - Slide-in HDD EE25 - 5AC801.HDDS-00 Panel PC 800 User's Manual V 1.00...
Page 107
2) Temperature values for 305 meter altitude. The temperature specification must be reduced linearly by 1°C every 305 meters. The temperature increase and decrease can be a maximum of 20°C per hour. 3) Humidity gradient: Maximum 15% per hour. Panel PC 800 User's Manual V 1.00...
Page 108
Figure 46: Temperature humidity diagram - 5AC801.HDDS-00 Temperature values for 305 meter altitude. The temperature specification must be reduced linearly by 1°C every 305 meters. The temperature increase and decrease can be a maximum of 20°C per hour. Panel PC 800 User's Manual V 1.00...
Features 5AC801.DVDS-00 Reading rate Data transfer rate max. 1.5 Gbit/s Access time (average) 130 ms 140 ms Table 61: Technical data - 5AC801.DVDS-00 Panel PC 800 User's Manual V 1.00...
Page 110
Table 61: Technical data - 5AC801.DVDS-00 (cont.) 1) Temperature data is for operation at 500 meters. Derating the max. ambient temperature - typically 1°C per 1000 meters (from 500 meters above sea level). 2) Drive surface temperature Panel PC 800 User's Manual V 1.00...
Page 111
1°C per 1000 meters (from 500 meters above sea level). Hot plug capable Hardware revision B0 of the slide-in DVD-ROM - 5AC801.DVDS-00 does not offer SATA hot plug capability. Other hardware revisions are hot plug capable. Panel PC 800 User's Manual V 1.00...
Technical data • Individual components 3.9.7 Slide-in DVD-R/RW - 5AC801.DVRS-00 Information: The expansion 5AC803.SX01-00 or 5AC803.SX02-00 is required in order to use slide- in drives. Figure 49: Slide-in DVD-R/RW - 5AC801.DVRS-00 Panel PC 800 User's Manual V 1.00...
Page 113
Disk at once, session at once, packet write, track at once Disk at once, incremental, over-write, sequential, multi-session Laser class Class 1 laser Table 62: Technical data - Slide-in DVD-R/RW, DVD+R/RW - 5AC801.DVRS-00 Panel PC 800 User's Manual V 1.00...
Page 114
5SWUTI.0000-00) or other burning software packages and drivers from third party providers. 2) Temperature data is for operation at 500 meters. Derating the max. ambient temperature - typically 1°C per 1000 meters (from 500 meters above sea level). 3) Drive surface temperature Panel PC 800 User's Manual V 1.00...
Page 115
Figure 50: Temperature humidity diagram - Slide-in DVD-R/RW, DVD+R/RW - 5AC801.DVRS-00 Temperature data is for operation at 500 meters. Derating the max. ambient temperature - typically 1°C per 1000 meters (from 500 meters above sea level). Panel PC 800 User's Manual V 1.00...
(UPS). If the operating system is shut down improperly, the next time it is started it is detected as an error by the RAID 1, and a complete rebuild is executed. This generally takes at least 120 minutes (configurable) to complete. Panel PC 800 User's Manual V 1.00...
Page 117
0.3 A at 3.3 V (PCI bus) 1 A at 5 V (PCI bus) Mechanical characteristics Mounted on PCI insert Fixed Weight 350 g Table 63: Technical data - RAID hard disk - 5ACPCI.RAIC-03 Panel PC 800 User's Manual V 1.00...
Page 118
3) Operation in areas prone to vibration and shock can affect performance negatively (reduction of transfer rate). 4) Operation in areas prone to vibration and shock can affect performance negatively (reduction of transfer rate). Panel PC 800 User's Manual V 1.00...
Page 119
Required drivers can only be downloaded from the B&R homepage, not from manufacturers' pages. Configuration For configuration of a SATA RAID network, see Chapter 3 "Commissioning", section 7 "Configuration of a SATA RAID array", on page 155. Panel PC 800 User's Manual V 1.00...
Page 120
A hard drive can be easily exchanged in the event of an error when using the RAID1 (mirroring) configuration without having to re-install the system. The replacement SATA HDD 160GB 5ACPCI.RAIC-04 is available as a replacement part for a HDD. Panel PC 800 User's Manual V 1.00...
SATA 1.0, PIO mode 0-4, multiword DMA mode 0-2, UDMA 0-5 Data transfer rate On the medium Max. 84.6 MBit/s To/from host Max. 150 MB/s Table 64: Technical data - RAID hard disk - 5ACPCI.RAIC-04 Panel PC 800 User's Manual V 1.00...
Page 122
3) Operation in areas prone to vibration and shock can affect performance negatively (reduction of transfer rate). 4) Operation in areas prone to vibration and shock can affect performance negatively (reduction of transfer rate). Panel PC 800 User's Manual V 1.00...
Page 123
Technical data • Individual components Temperature humidity diagram - Operation and storage Operation Temperature [°C] Figure 54: Temperature humidity diagram - SATA RAID hard disk 5ACPCI.RAIC-04 Panel PC 800 User's Manual V 1.00...
5AC803.FA01-00 Fan type Width 40 mm Length 40 mm Height 10 mm Revolution speed 6100 rpm Noise level 21 dB Lifespan 95,000 at 20°C 29,000 at 70°C Table 65: Technical data - 5AC803.FA01-00 Panel PC 800 User's Manual V 1.00...
The fans are subject to wear. Depending on the work environment, the dust filter should be checked with appropriate frequency to determine whether the air flow provides sufficient cooling. An exchange or cleaning of the filter kit is appropriate at that time. Table 66: Technical data - 5AC803.FA02-00 Panel PC 800 User's Manual V 1.00...
The fans are subject to wear. Depending on the work environment, the dust filter should be checked with appropriate frequency to determine whether the air flow provides sufficient cooling. An exchange or cleaning of the filter kit is appropriate at that time. Table 67: Technical data - 5AC803.FA03-00 Panel PC 800 User's Manual V 1.00...
Commissioning • Installation Chapter 3 • Commissioning 1. Installation Panel PC 800 devices are best mounted in a housing cutout using the clamps found on the housing (different designs possible). Plastic (PA6) Aluminum dye cast Aluminum dye cast with clip...
Be sure the wall or switching cabinet can withstand four times the total weight of the the PPC800. • When connecting certain cable types (DVI, SDL, USB, etc.), keep the flex radius in mind. Panel PC 800 User's Manual V 1.00...
Figure 59: Mounting orientation - Standard mounting In order to guarantee natural air circulation, mount the system so that the spacing on the top, bottom, and sides is as indicated in section 1.2.4 "Spacing for air circulation.". Panel PC 800 User's Manual V 1.00...
Figure 60: Mounting orientation - Standard mounting In order to guarantee natural air circulation, mount the system so that the spacing on the top, bottom, and sides is as indicated in section 1.2.4 "Spacing for air circulation.". Panel PC 800 User's Manual V 1.00...
Figure 61: Mounting orientation - Standard mounting In order to guarantee natural air circulation, mount the system so that the spacing on the top, bottom, and sides is as indicated in section 1.2.4 "Spacing for air circulation.". Panel PC 800 User's Manual V 1.00...
1.2.4 Spacing for air circulation. In order to guarantee proper air circulation, allow the specified amount of space above, below, to the side and behind the Panel PC 800. The minimum specified free space can be found in the diagram below.
When making cable connections and installing cables, it is not permitted to have a flex radius smaller than the minimum value specified. Information: The value specified for the minimum flex radius can be found in the technical data for the cable that is being used. Panel PC 800 User's Manual V 1.00...
Note the line shielding concept. All data cables connected to the device must use shielded lines. Switching cabinet Grounding strip Ground connection Supply voltage min. 2.5mm² min. 2.5mm² Figure 63: Grounding concept Panel PC 800 User's Manual V 1.00...
5PC800.B945-02 ✓ ✓ Max. SXGA 5PC800.B945-12 5PC800.B945-03 ✓ ✓ Max. SXGA 5PC800.B945-13 5PC800.B945-04 ✓ ✓ Max. SXGA 5PC800.B945-14 ✓ ✓ 5PC800.B945-05 Max. SXGA Table 69: Possible combinations of system unit and CPU board Panel PC 800 User's Manual V 1.00...
5 m / 10 m ✓ 5AP920.1706-01 17.0“ SXGA 5 m / 10 m ✓ 5AP920.1906-01 19.0“ SXGA 5 m / 10 m Table 72: Possible Automation Panel units, resolutions und segment lengths Panel PC 800 User's Manual V 1.00...
1) USB support is not possible on the Automation Panel 900 because USB is limited to 5 m. Information: The DVI transfer mode does not allow reading statistical values on Automation Panel 900 units. 4.2.5 BIOS settings No special BIOS settings are necessary for operation. Panel PC 800 User's Manual V 1.00...
5PC800.B945-02 ✓ ✓ Max. UXGA 5PC800.B945-12 5PC800.B945-03 ✓ ✓ Max. UXGA 5PC800.B945-13 5PC800.B945-04 ✓ ✓ Max. UXGA 5PC800.B945-14 ✓ ✓ 5PC800.B945-05 Max. UXGA Table 73: Possible combinations of system unit and CPU board Panel PC 800 User's Manual V 1.00...
Table 75: Cables for SDL configurations Information: Detailed technical data about the cables can be found in the Automation Panel 900 User's Manual. This can be downloaded as a .pdf file from the B&R homepage www.br-automation.com. Panel PC 800 User's Manual V 1.00...
The COM C must be enabled in BIOS in order to operate the connected panel touch screen on the monitor / panel connection (found in the BIOS menu under "Advanced - Main board / Panel Features - Legacy Devices"). Panel PC 800 User's Manual V 1.00...
5PC800.B945-02 ✓ ✓ Max. UXGA 5PC800.B945-12 5PC800.B945-03 ✓ ✓ Max. UXGA 5PC800.B945-13 5PC800.B945-04 ✓ ✓ Max. UXGA 5PC800.B945-14 ✓ ✓ 5PC800.B945-05 Max. UXGA Table 77: Possible combinations of system unit and CPU board Panel PC 800 User's Manual V 1.00...
The following table shows the relationship between segment lengths and the maximum resolution according to the SDL cable used: Cables Resolution Segment length [m] 1024 x 768 5CASDL.0018-20 5CASDL.0050-20 5CASDL.0100-20 5CASDL.0150-20 5CASDL.0200-20 5CASDL.0250-20 5CASDL.0300-30 5CASDL.0400-30 Table 79: Segment lengths, resolutions and SDL cables Panel PC 800 User's Manual V 1.00...
The COM C must be enabled in BIOS in order to operate the connected panel touch screen on the monitor / panel connection (found in the BIOS menu under "Advanced - Main board / Panel Features - Legacy Devices"). Panel PC 800 User's Manual V 1.00...
5PC800.B945-02 ✓ ✓ Max. UXGA 5PC800.B945-12 5PC800.B945-03 ✓ ✓ Max. UXGA 5PC800.B945-13 5PC800.B945-04 ✓ ✓ Max. UXGA 5PC800.B945-14 ✓ ✓ 5PC800.B945-05 Max. UXGA Table 80: Possible combinations of system unit and CPU board Panel PC 800 User's Manual V 1.00...
The COM C must be enabled in BIOS in order to operate the connected panel touch screen on the monitor / panel connection (found in the BIOS menu under "Advanced - Main board / Panel Features - Legacy Devices"). Panel PC 800 User's Manual V 1.00...
✓ ✓ Max. UXGA 5PC800.B945-10 5PC800.B945-01 ✓ ✓ Max. UXGA 5PC800.B945-11 5PC800.B945-02 ✓ ✓ Max. UXGA 5PC800.B945-12 5PC800.B945-03 ✓ ✓ Max. UXGA 5PC800.B945-13 Table 82: Possible combinations of system unit and CPU board Panel PC 800 User's Manual V 1.00...
30 m 5CASDL.0300-03 SDL cable for fixed and flexible type of layout 30 m 5CASDL.0300-10 SDL cable with extender for a fixed type of layout 30 m Table 84: Cables for SDL configurations Panel PC 800 User's Manual V 1.00...
The COM C must be enabled in BIOS in order to operate the connected panel touch screen on the monitor / panel connection (found in the BIOS menu under "Advanced - Main board / Panel Features - Legacy Devices"). Panel PC 800 User's Manual V 1.00...
The touch screen should be calibrated while installing the driver. 5.5 Automation Runtime / Visual Components The first time the touch screen is used, it must be calibrated once in the customer application for the existing device and project. Panel PC 800 User's Manual V 1.00...
6.1 Locally on the PPC800 Many different peripheral USB devices can be connected to the 2 or 5 USB interfaces on the Panel PC 800. These can each handle a maximum load of 1A. The maximum transfer rate is USB 2.0.
USB memory media e.g. flash drive USB input devices USB drives USB display devices e.g. keyboard e.g. CD ROM drive e.g. mouse Figure 70: Remote connection of USB peripheral devices to the APC900 via DVI Panel PC 800 User's Manual V 1.00...
USB memory media e.g. flash drive USB input devices USB drives USB display devices e.g. keyboard e.g. CD ROM drive e.g. mouse Figure 71: Remote connection of USB peripheral devices to the APC800/900 via SDL Panel PC 800 User's Manual V 1.00...
Rebuild Mirrored set Resolve Conflicts Low Level Format * 0 PM ST96023AS 55GB 1 SM ST96023AS 55GB Select Menu Previous Menu Enter Select Ctrl-E Exit First HDD Figure 73: RAID Configuration Utility - Menu Panel PC 800 User's Manual V 1.00...
Enter Select Ctrl-E Exit First HDD Figure 74: RAID Configuration Utility - Menu The RAID system can be recreated as "Striped" = RAID0 or "Mirrored" = RAID1 using the menu "Create RAID set". Panel PC 800 User's Manual V 1.00...
Figure 75: RAID Configuration Utility - Create RAID set - Striped Auto configuration Auto configuration optimizes all settings. "Manual configuration" It is possible to specify the first and second HDD as well as the "Chunk Size" (= block size, application-dependent). Panel PC 800 User's Manual V 1.00...
Auto configuration Auto configuration optimizes all settings. "Manual configuration" It is possible to specify the "Source" and "Target" HDD, and also to specify whether a rebuild (mirror) should be performed immediately (approx. 50 minutes). Panel PC 800 User's Manual V 1.00...
1 ST96023AS Chunk Size Previous Menu Enter Select Ctrl-E Exit First HDD Figure 77: RAID Configuration Utility - Delete RAID set An existing RAID set can be deleted using the menu "Delete RAID set". Panel PC 800 User's Manual V 1.00...
SATARaid detected a new event and the rebuild is started. The entire rebuild lasts approximately 50 minutes. If "offlinerebuild" is selected, then a rebuild is performed immediately before starting the operating system (lasts approximately 30 minutes). Panel PC 800 User's Manual V 1.00...
Figure 79: RAID Configuration Utility - Resolve conflicts Conflicts in a RAID set can be resolved using the "Resolve conflicts" menu. This function is only available if the status of the hard disk is "conflict". Panel PC 800 User's Manual V 1.00...
Individual hard disks can be configured using the "Low Level Format" menu. This can only be done if a RAID set is not configured. A low level format of a hard disk takes approx. 40 minutes. Panel PC 800 User's Manual V 1.00...
The functionality of the touch system is not affected by this. This can be avoided by setting a panel locking time of 50 ms. The panel locking time can be configured with the B&R Key Editor. Panel PC 800 User's Manual V 1.00...
Line type: This can cause lasting damage. 9.2.1 What causes image sticking? • Static images • Screensaver not enabled • Sharp contrast transitions (e.g. black / white) • High ambient temperatures • Operation outside of the specifications Panel PC 800 User's Manual V 1.00...
• avoiding excessive brightness contrast between foreground and background display • use of colors with similar brightness • use of complementary colors in subsequent images • use of screensavers Panel PC 800 User's Manual V 1.00...
Page 166
Commissioning • User tips for increasing the display lifespan Panel PC 800 User's Manual V 1.00...
1.1 General information BIOS stands for "Basic Input Output System". It is the most basic standardized communication between the user and the system (hardware). The BIOS system used in the Panel PC 800 systems is produced by American Megatrends Inc.
The key signals from the USB keyboard are only registered after the USB controller has been initialized. Function Enters the BIOS setup menu. Using the F12 key, you can boot from the network. Table 87: 945GME - Bios-relevant keys at POST Panel PC 800 User's Manual V 1.00...
Page 169
The colors of the BIOS Setup are switched. Changes are reset. These settings are loaded for all BIOS configurations. Save and close. Exits the submenu. Table 88: 945GME - Bios-relevant keys in the BIOS menu Panel PC 800 User's Manual V 1.00...
BC Firmware Rev. Displays the CPU board controller None firmware revision. MAC Address Displays the MAC addresses assigned for None (ETH1) the ETH1 interface. Table 89: 945GME - Main Menu - Setting options Panel PC 800 User's Manual V 1.00...
Opens the submenu configuration See "Graphics configuration", on page 181. CPU configuration Configures the CPU settings. Enter Opens the submenu See "CPU configuration", on page 185. Table 90: 945GME - Advanced Menu - Setting options Panel PC 800 User's Manual V 1.00...
Page 172
Main Board/Panel Displays device specific information and Enter Opens the submenu Features setup of device specific values. See "Main Board/Panel Features", on page 204. Table 90: 945GME - Advanced Menu - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
Enables this function. from S3/S4 on a connected USB device to wake the Disabled Disables the function system up from the S3/S4 standby mode. Table 91: 945GME - Advanced ACPI configuration - Setting options Panel PC 800 User's Manual V 1.00...
Page 174
Temperature setting for the critical trip point. Can set at which the operating system 100°C, 105°C, 110°C be set in 5 degree increments. automatically shuts itself down. Table 91: 945GME - Advanced ACPI configuration - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
See "PCI IRQ Resource Exclusion", on page 176 PCI Interrupt Configures PCI interrupt routing Enter Opens the submenu Routing See "PCI Interrupt Routing", on page 177 Table 92: 945GME - Advanced PCI configuration - Setting options Panel PC 800 User's Manual V 1.00...
Page 176
Allocated by the system - cannot be used. devices. Available Available - can be used. Reserved Reserved - cannot be used. Table 93: 945GME - Advanced PCI IRQ Resource Exclusion - Setting options Panel PC 800 User's Manual V 1.00...
Page 177
Manual assignment. PIRQ E Option for setting the PIRQ E. Auto Automatic assignment by the BIOS and operating (INTD,UHCI3,PATA) system. 5,6,7,9,10,11,12 Manual assignment. Table 94: 945GME - Advanced PCI Interrupt Routing - Setting options Panel PC 800 User's Manual V 1.00...
Page 178
Assigns the PIRQ as 3rd exclusive PCI IRQ. exclusively (no IRQ sharing). Information: Only displayed when three PIRQs are set manually. Table 94: 945GME - Advanced PCI Interrupt Routing - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
Enabled Enables this function. Information: Disabled Disables this function. If you are not using any PCI Express devices, this option should deactivated. Table 95: 945GME - Advanced PCI Express Configuration - Setting options Panel PC 800 User's Manual V 1.00...
Page 180
Interrupt Controller) on the PCIE port 0. The IRQ resources available to the system are expanded when the APIC mode is enabled. Table 95: 945GME - Advanced PCI Express Configuration - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
SDVO Port C Device [None] Change Option General Help SDVO/DVI Hotplug Support [Enabled] Save and Exit Display Mode Persistence [Enabled] Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Figure 89: 945GME - Advanced Graphics Configuration Panel PC 800 User's Manual V 1.00...
Page 182
Boot Display Device option is set to SDVO-C SDVO-B LFP Serial Digital Video C output - Serial Digital Video "Auto". B output - Local Flat Panel. Table 96: 945GME - Advanced Graphics Configuration - Setting options Panel PC 800 User's Manual V 1.00...
Page 183
Video signal output is optimized for a LVDS- compatible video device. DVI-Analog Video signal output is optimized for an analog DVI-compatible video device. Table 96: 945GME - Advanced Graphics Configuration - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
Page 184
DVI monitors are reconnected, even if only one of them was connected and activated during a previous boot. Table 96: 945GME - Advanced Graphics Configuration - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
Minimum speed The processor speed is set to a minimum. result, the power consumption depends Disabled Disables SpeedStep technology. largely on the processor load. Table 97: 945GME - Advanced CPU Configuration - Setting options Panel PC 800 User's Manual V 1.00...
APIC ACPI SCI IRQ [Disabled] C4 On C3 [Disabled] Select Screen Select Item Change Option General Help Save and Exit Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Figure 91: 945GME Advanced Chipset Configuration Panel PC 800 User's Manual V 1.00...
Page 187
Fine-tunes the power saving function on Disabled Disables this function. an ACPI operating system. Enabled Processor is needed in C4 if the operating system is initiated in a C3 state. Table 98: 945GME Advanced Chipset setting options Panel PC 800 User's Manual V 1.00...
The audio mode can be selected or Enables High Definition Audio sound. Controller switched off here. AC97 Enables AC'97 sound. Disabled Disables the audio controller. Table 99: 945GME Advanced I/O Interface Configuration setting options Panel PC 800 User's Manual V 1.00...
Setting options Effect Spread spectrum With this option, the cycle frequency can Enabled Enables this function. be modulated by reducing Disabled Disables this function. electromagnetic disturbances. Table 100: 945GME Advanced Clock Configuration setting options Panel PC 800 User's Manual V 1.00...
The AHCI setting enables the internal memory driver for the SATA functions, which increase the storage performance for random read-write access by allowing the drive to determine the sequence of commands. Table 101: 945GME Advanced IDE Configuration setting options Panel PC 800 User's Manual V 1.00...
Page 191
3) These settings are only possible if ATA/IDE Configuration is set to Enhanced and Configure SATA as to IDE. 4) These settings are only possible if ATA/IDE Configuration is set to Enhanced and Configure SATA as to RAID or AHCI. Panel PC 800 User's Manual V 1.00...
Page 192
Automatic enabling of this function when enabled, the number of blocks per request supported by the system. from the configuration sector of the hard drive is read. Table 102: 945GME - Primary IDE Master - Setting options Panel PC 800 User's Manual V 1.00...
Page 193
Enabled Enables this function. 32 Bit Data Transfer This function enables 32-bit data transfer. Disabled Disables this function. Enabled Enables this function. Table 102: 945GME - Primary IDE Master - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
Page 194
Automatic enabling of this function when enabled, the number of blocks per request supported by the system. from the configuration sector of the hard drive is read. Table 103: 945GME - Primary IDE Slave - Setting options Panel PC 800 User's Manual V 1.00...
Page 195
DMA Mode [Auto] S.M.A.R.T. [Auto] 32Bit Data Transfer [Enabled] Select Screen Select Item Change Option General Help Save and Exit Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Figure 97: 945GME - Secondary IDE Master Panel PC 800 User's Manual V 1.00...
Page 196
Enabled Enables this function. 32 Bit Data Transfer This function enables 32-bit data transfer. Disabled Disables this function. Enabled Enables this function. Table 104: 945GME - Secondary IDE Master - Setting options Panel PC 800 User's Manual V 1.00...
Page 197
Automatic enabling of this function when enabled, the number of blocks per request supported by the system. from the configuration sector of the hard drive is read. Table 105: 945GME - Secondary IDE Slave - Setting options Panel PC 800 User's Manual V 1.00...
USB Beep Message [Enabled] Save and Exit USB Stick Default Emulation [Hard Disk] Exit USB Mass Storage Reset Delay [20 Sec] v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Figure 99: 945GME - Advanced USB Configuration Panel PC 800 User's Manual V 1.00...
Page 199
Hard Disk An HDD-formatted drive can be used as an FDD (e.g. zip drive) for starting the system. Table 106: 945GME - Advanced USB Configuration - Setting options Panel PC 800 User's Manual V 1.00...
NumLock key when booting. are enabled. Numeric keypad is enabled. Typematic rate The key repeat function is set here. Slow Slow key repeat. Fast Fast key repeat. Table 107: 945GME Advanced Keyboard/Mouse Configuration setting options Panel PC 800 User's Manual V 1.00...
The setting must be the same on the Software The interface transfer control is carried out terminal and the server. through software. Table 108: 945GME - Advanced Remote Access Configuration - Setting options Panel PC 800 User's Manual V 1.00...
Page 202
Enabled Enables this function. processor. Information: If this option is disabled, the boot time is reduced. Table 108: 945GME - Advanced Remote Access Configuration - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
Displays the processor's temperature (in None degrees Celsius and Fahrenheit). Top DIMM Displays the temperature of the first None Environment Temp. DRAM module. Table 109: 945GME - Advanced Remote Access Configuration - Setting options Panel PC 800 User's Manual V 1.00...
Serial Number: AF210168427 Enter Go to Sub Screen Product Name: 5PC820.1505-00 General Help User Serial ID: 00000000h Save and Exit Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Figure 103: 945GME - Advanced Baseboard/Panel Features Panel PC 800 User's Manual V 1.00...
Page 205
(e.g. to give the device a unique ID) and can only be changed with using the "B&R Control Center" via the ADI driver. Table 110: 945GME - Advanced Baseboard/Panel Features - Setting options Panel PC 800 User's Manual V 1.00...
Page 206
(in degrees Celsius and Fahrenheit). Fan speed Displays fan speed for the selected panel. None Keys/LEDs None Displays the available keys and LEDs on the selected panel. Table 111: 945GME - Panel Control - Setting options Panel PC 800 User's Manual V 1.00...
Page 207
Celsius and Fahrenheit. Case 1 Displays the fan speed of housing fan 1. None Case 2 Displays the fan speed of housing fan 2. None Table 112: 945GME Baseboard Monitor setting options Panel PC 800 User's Manual V 1.00...
Page 208
Base I/O address Selection of the base I/O address for the 238, 2E8, 2F8, 328, 338, Selected base I/O address is assigned. COM port. 3E8, 3F8 Table 113: 945GME - Legacy Devices - Setting options Panel PC 800 User's Manual V 1.00...
Page 209
Disabled Disables the controller. (ETH2) on and off. Enabled Enables the controller. ETH2 MAC Address Displays the Ethernet 2 controller MAC None address. Table 113: 945GME - Legacy Devices - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
The boot sequence of a device type list can be changed. Device types that are not connected can also be entered to this list. Table 114: 945GME - Boot Menu - Setting options Panel PC 800 User's Manual V 1.00...
Page 211
Determines if the system is on/off Remain Off Remains off. following power loss. Turn On Powers on. Last State Enables the previous state. Table 114: 945GME - Boot Menu - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
The hard disk security user password can Enter Opens the submenu User Passwords be created here. See "Hard disk security user password", on page 213 Table 115: 945GME - Security Menu - Setting options Panel PC 800 User's Manual V 1.00...
A user password allows the user to edit only certain BIOS settings. Table 116: 945GME Hard disk security user password Panel PC 800 User's Manual V 1.00...
This function makes it possible to use the Enter Enter password. Master Password user password to change or configure each hard drive without having to reboot the device. Table 117: 945GME Hard Disk Security Master Password Panel PC 800 User's Manual V 1.00...
Keyboard or PS/2 mouse activities return the Mouse saving mode is determined here. system to its normal state from a particular energy saving mode. IGNORE Activities are ignored. Table 118: 945GME - Power Menu - Setting options Panel PC 800 User's Manual V 1.00...
Page 216
Power Button Mode This function determines the function of On/Off Power button switches on/off. the power button. Suspend Suppresses the function. Table 118: 945GME - Power Menu - Setting options (cont.) Panel PC 800 User's Manual V 1.00...
Table 119: 855GME - (XTX) Exit menu - Setting options 1.9 BIOS default settings The various positions of the CMOS profile hex switch (see figure "Rear view 5PC820.1505-00", on page 66) can be used to load pre-defined BIOS profile settings. Panel PC 800 User's Manual V 1.00...
Page 218
Table 120: Profile overview The following pages provide an overview of the BIOS default settings for the different CMOS profile switch positions. Settings highlighted in yellow are variations from the BIOS default profile (=profile 0). Panel PC 800 User's Manual V 1.00...
USB Device Wakeup from Disabled Disabled S3/S4 Active Cooling Trip Point Disabled Disabled Passive Cooling Trip Point Disabled Disabled Critical Trip Point 105°C 105°C Table 122: 945GME Advanced - ACPI configuration profile setting overview Panel PC 800 User's Manual V 1.00...
Page 220
PIRQ F (INTA) Auto Auto PIRQ G (INTB) Auto Auto PIRQ H Auto Auto (INTC,UHCI0,EHCI) 1st Exclusive PCI 2nd Exclusive PCI 3rd Exclusive PCI Table 123: 945GME Advanced - PCI configuration profile setting overview Panel PC 800 User's Manual V 1.00...
Page 221
Expand Text & Graphics SDVO Port B Device SDVO Port C Device None SDVO/DVI Hotplug Enabled Enabled Support Display Mode Persistence Enabled Enabled Table 125: 945GME Advanced - Graphics configuration profile setting overview Panel PC 800 User's Manual V 1.00...
Page 223
Auto Auto Block (Multi-Sector Auto Auto Transfer) PIO Mode Auto Auto DMA Mode Auto Auto S.M.A.R.T. Auto Auto 32Bit data transfer Enabled Enabled Table 130: 945GME Advanced - IDE configuration profile setting overview Panel PC 800 User's Manual V 1.00...
Page 224
Table 131: 945GME Advanced - USB configuration profile setting overview Keyboard/mouse configuration Setting / View Profile 0 Profile 5 My setting Boot-up Num-lock Typematic rate Fast Fast Table 132: 945GME Advanced - Keyboard/Mouse Configuration profile setting overview Panel PC 800 User's Manual V 1.00...
Page 225
Case 1 Case 2 Case 3 Case 4 Legacy devices COM A Enabled Enabled Base I/O address Interrupt IRQ4 IRQ4 COM C Enabled Enabled Table 135: 945GME Advanced - Baseboard/Panel Features profile setting overview Panel PC 800 User's Manual V 1.00...
Display Interrupt 19 Capture Disabled Disabled PXE boot to LAN (ETH1) Enabled Disabled Slide-in 2 optional ROM Enabled Disabled Power Loss Control Turn On Turn On Table 136: 945GME Boot profile setting overview Panel PC 800 User's Manual V 1.00...
Secondary Slave IDE MONITOR MONITOR Resume On Ring Disabled Disabled Resume on PME# Disabled Disabled Resume On RTC Alarm Disabled Disabled Power Button Mode On/Off On/Off Table 138: 945GME Power profile setting overview Panel PC 800 User's Manual V 1.00...
Software • BIOS options 1.10 BIOS Error signals (beep codes) While the Panel PC 800 is booting, the following messages and errors can occur with BIOS. These errors are signaled by different beeping codes. 1.10.1 BIOS 945GME Beeping code Meaning...
1) TOM - Top of memory: max. installed DRAM 2) Only if ACPI Aware OS is set to "YES" in the setup. 3) The VGA frame buffer can be reduced to 1 MB in the setup. Panel PC 800 User's Manual V 1.00...
Table 141: I/O address assignment 1) The BIOS assigns the PCI and PCI Express Bus I/O resources from FFF0h downward. Devices that are not compatible with PnP/PCI/PCI Express cannot use the I/O resources in this area. Panel PC 800 User's Manual V 1.00...
5) PIRQ D: for PCIe; UHCI host controller 1, SMBus controller, PCI Express root port 3, Serial ATA controller in enhanced/native mode 6) PIRQ E: PCI bus INTD, UHCI Host Controller 3, Parallel ATA controller in enhanced/native mode 7) PIRQ F: PCI bus INTA Panel PC 800 User's Manual V 1.00...
Page 233
APIC IRQ 22 PIRQ H USB UHCI-0 USB EHCI APIC IRQ 23 B0:D29:F0 B0:D29:F7 PCI 1 PCI 2 Figure 114: PCI and PCIe routing with activated APIC for CPU boards 945GME version 1.15 Panel PC 800 User's Manual V 1.00...
BIOS setup (information about changes can be found in the Readme files of the BIOS upgrade). 2.1.1 What information do I need? Information: Individually saved BIOS settings are deleted when upgrading the BIOS. Before you begin the upgrade, it helps to determine the various software versions. Panel PC 800 User's Manual V 1.00...
Page 235
Select Item Serial Number: A3C70168427 Enter Go to Sub Screen Product Name: 5PC820.1505-00 General Help User Serial ID: 00000000h Save and Exit Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Figure 115: Software version Panel PC 800 User's Manual V 1.00...
Page 236
Select Screen Select Item Change Option General Help Save and Exit Exit v02.59 (C)Copyright 1985-2005, American Megatrends, Inc. Figure 116: Firmware version of the AP Link SDL transmitter Panel PC 800 User's Manual V 1.00...
B945" is automatically carried out and the PPC800 is automatically updated. • The system must be rebooted after a successful upgrade. • Reboot and press "Del" to enter the BIOS setup menu and load the setup defaults, then select "Save Changes and Exit". Panel PC 800 User's Manual V 1.00...
The following boot menu options including descriptions are based on Version 1.02 of the PPC800 upgrade (MTCX, SDLR, SDLT) disk. In some cases, these descriptions might not match the version you are currently using. Panel PC 800 User's Manual V 1.00...
Page 239
The SDLR controller is automatically updated on Automation Panel 3. 2.5. Upgrade all SDLR (AP800/AP900) All SDLR controllers are automatically updated on all Automation Panels on the Monitor/Panel (default after 5 sec). 2.6. Return to main menu Returns to the main menu. Panel PC 800 User's Manual V 1.00...
Power button (to put the system in Standby mode), before executing the required power off/on. If not, the firmware upgrade will not work because the UPS buffers the system. Panel PC 800 User's Manual V 1.00...
Then select the checkbox Create an MS-DOS startup disk, press Start and acknowledge the warning message with OK. Figure 118: Creating a bootable diskette in Windows XP - step 2 Figure 119: Creating a bootable diskette in Windows XP - step 3 Panel PC 800 User's Manual V 1.00...
Page 242
Figure 120: Creating a bootable diskette in Windows XP - step 4 Figure 121: Creating a bootable diskette in Windows XP - step 5 Now all files (marked) except Command.com, IO.sys and MSDOS.sys can be deleted. Panel PC 800 User's Manual V 1.00...
In the B&R Upgrade text box, it's also possible to enter the path to the ZIP file for the B&R Upgrade Disk and select the file. • Click on the Start action button in the toolbar. Panel PC 800 User's Manual V 1.00...
Information concerning creating an MS-DOS boot diskette can be found in section 2.3 "Creating an MS-DOS boot diskette in Windows XP", on page 241. Then the files from the diskette are to be copied to your hard drive. Panel PC 800 User's Manual V 1.00...
In the B&R Upgrade text box, it's also possible to enter the path to the ZIP file for the B&R Upgrade Disk and select the file. • Click on the Start action button in the toolbar. Panel PC 800 User's Manual V 1.00...
MS-DOS boot diskette in Windows XP", on page 241. Then the files from the diskette are to be copied to your hard drive. 2.6 Upgrade problems Potential upgrade problems are listed in the Liesmich.txt or Readme.txt files on the upgrade disks. Panel PC 800 User's Manual V 1.00...
Page 248
Software • Panel PC 800 with MS-DOS The following table shows the tested resolutions and color depths on the Monitor / Panel connector with 945GME CPU boards. Color depth Resolutions for DVI 8-bit 16-bit 24-bit ✓ ✓ ✓ 640 x 480 ✓...
Software • Panel PC 800 with Windows XP Professional 4. Panel PC 800 with Windows XP Professional Figure 125: Windows XP Professional Logo Model number Short description Note 5SWWXP.0600-GER WinXP Professional with SP3, GER Microsoft OEM Windows XP Professional Service Pack 3, CD, German. Only available with a new device.
Software • Panel PC 800 with Windows XP Embedded 5. Panel PC 800 with Windows XP Embedded Figure 126: Windows XP Embedded Logo Model number Short description Note 5SWWXP.0427-ENG WinXPe FP2007 PPC800 945GME Order Microsoft OEM Windows XP embedded Feature Pack 2007, English; for PPC800 with CPU boards 5PC800.B945-00, 5PC800.B945-01, 5PC800.B945-02, 5PC800.B945-03,...
Software • Panel PC 800 with Windows XP Embedded 5.2 Features with FP2007 (Feature Pack 2007) The feature list shows the most important device functions in Windows XP Embedded with Feature Pack 2007 (FP2007). Function Present ✓ Enhanced write filter (EWF) ✓...
Software • Panel PC 800 with Windows XP Embedded 5.3 Installation Upon request, Windows XP Embedded can be preinstalled at B&R Austria on a suitable CompactFlash card (min. 512MB). The PPC800 system is then automatically configured after it has been switched on for the first time. This procedure takes approximately 30 minutes, and the device will be rebooted a number of times.
Software • Panel PC 800 with Windows Embedded Standard 2009 6. Panel PC 800 with Windows Embedded Standard 2009 Figure 127: Windows Embedded Standard 2009 Logo Model number Short description Note 5SWWXP.0727-ENG Windows Embedded Standard 2009 PPC800 945GME Order Microsoft OEM Windows Embedded Standard 2009, English; for PPC800 with CPU boards 5PC800.B945-00, 5PC800.B945-01, 5PC800.B945-02, 5PC800.B945-03,...
Software • Panel PC 800 with Windows Embedded Standard 2009 6.2 Features with WES2009 (Windows Embedded Standard 2009) The feature list shows the most important device functions in Windows Embedded Standard 2009. Function Present ✓ Enhanced write filter (EWF) ✓...
Software • Panel PC 800 with Windows Embedded Standard 2009 6.3 Installation Upon request, Windows Embedded Standard 2009 can be preinstalled at B&R Austria on a suitable CompactFlash card (min. 1GB). The PPC800 system is then automatically configured after it has been switched on for the first time. This procedure takes approximately 30 minutes, and the device will be rebooted a number of times.
Automation Studio™ configuration 7.2 AR010 The hardware dongle 1A4300.LZ1U must be connected to use AR010 on a Panel PC 800 (see section 11 "B&R Automation Studio 3.0USBdongle", on page 323). Panel PC 800 User's Manual V 1.00...
The hardware components used have automatic diagnostics functions that can be applied in the event of error. 8.1 Function • Adjusting the display-specific parameters of connected Panels • Reading of device-specific keys Panel PC 800 User's Manual V 1.00...
Page 258
Content of B&R Windows XP Embedded image Mobile Panel BIOS devices Windows CE Content of B&R Windows CE image Together with APC620/ APC810/ APC820/ PPC700/ Automation Panel 800 PPC800 Table 151: System support - ADI driver Panel PC 800 User's Manual V 1.00...
If a more current ADI driver version exists (see the B&R homepage download area), it can be installed later. A potentially activated "Enhanced Write Filter (EWF)" must be taken into consideration when installing. Panel PC 800 User's Manual V 1.00...
The value is optimally defined for the cable length when using the "Automatic setting". The equalizer value can only be changed if the function is supported by Automation Panel 900 (starting with Panel Firmware version 1.04 or higher). Panel PC 800 User's Manual V 1.00...
The installed UPS must be selected and configured in the Control Panel using the energy options in order for battery operation to be supported. Information: The UPS service is supported starting with B&R Windows Embedded Version 2.10 or higher. Panel PC 800 User's Manual V 1.00...
In UPS firmware Version 1.07 or smaller, a change between battery operation and normal operation can lead to communication errors. 3) Select UPS monitor to display UPS status changes since the last time the system or UPS driver was started. Panel PC 800 User's Manual V 1.00...
Page 263
"low" in the energy options, even if the battery is OK (Windows error). In an English version, three battery status levels are displayed: unknown, OK, replace A low battery status is never displayed. Panel PC 800 User's Manual V 1.00...
B&R under a new name and make adjust the settings in this file for the battery being used. Current files with settings for batteries from B&R can be updated using B&R's "Upgrade PPC800 MTCX" software. Panel PC 800 User's Manual V 1.00...
Deleting the data in flash memory can take several seconds depending on the memory block being used. The progress indicator is not updated during this time. Information: The UPS is automatically restarted after a successful download. This can cause a brief failure in the UPS communication. Panel PC 800 User's Manual V 1.00...
3) Click on Change under UPS settings. This opens the following dialog box: Figure 133: ADI Control Center - UPS settings Further information regarding the UPD system settings can be found in the Windows help. Panel PC 800 User's Manual V 1.00...
Page 267
Low battery shutdown time. This will allow the operating system to shut down properly when UPS service is enabled. Panel PC 800 User's Manual V 1.00...
1) Open the Control Center in the Control Panel. 2) Select UPS tab. 3) Click on Advanced under UPS settings. This opens the following dialog box: Figure 134: ADI Control Center - Advanced UPS settings Panel PC 800 User's Manual V 1.00...
Page 269
If the checkbox Display UPS status with UPS monitor is also activated, a new message is not displayed for every change, but only a general message and request for you to start the B&R UPS monitor. As long as the UPS monitor is active, no new messages are displayed. Panel PC 800 User's Manual V 1.00...
Page 270
Software • Automation Device Interface (ADI) - Control Center Information: Regardless of these options, all changes to the UPS status are logged in Windows event protocol (under "Application"). Panel PC 800 User's Manual V 1.00...
3: Stationary use at weather-protected locations EN 61000-3-2 Electromagnetic compatibility (EMC) - part 3-2: Limits for harmonic current emissions (equipment input current ≤ 16 A per phase) Table 152: Overview of standards Panel PC 800 User's Manual V 1.00...
Page 272
Federal Communications Commission (FCC), 47 CFR Part 15 Subpart B Class A VCCI V-3 Agreement of Voluntary Control Council for Interference by Information Technology Equipment; Class ICES 003 Devices that cause interference - Digital devices; Class A Table 152: Overview of standards (cont.) Panel PC 800 User's Manual V 1.00...
≤ 16 A per phase and not subject to low-voltage supply systems, equipment with rated current ≤ 16 conditional connection, class A/D A per phase, and not subject to conditional connection. Table 153: Overview of limits and testing guidelines for emissions Panel PC 800 User's Manual V 1.00...
Average Other connections 150 kHz - 500 kHz Other connections 500 kHz - 30 MHz Table 154: Test requirements - Network-related emissions for industrial areas 1) AC network connections only with EN 61131-2 Panel PC 800 User's Manual V 1.00...
10 m Quasi-peak value > 960 MHz < 300 dB (µV/m) measured at a distance of 10 m Quasi-peak value Table 155: Test requirements - Electromagnetic emissions for industrial areas Panel PC 800 User's Manual V 1.00...
A temporary function failure is permitted if the function restores itself, or the function can be restored by activating configuration and control elements. Criteria D: Deterioration or failure of the function, which can no longer be established (operating equipment destroyed). Panel PC 800 User's Manual V 1.00...
±0.5 kV, criteria B DC power outputs, L to PE ±1 kV, criteria B ±1 kV, criteria B Signal connections >30 m ±1 kV, criteria B All shielded cables Table 160: Test requirements - Surge voltages Panel PC 800 User's Manual V 1.00...
AC power inputs Voltage interruptions < 5% (> 95% reduction), 250 periods, criteria C AC power inputs 20 interruptions, 0.5 periods, criteria A Table 163: Test requirements - Voltage dips, fluctuations, and short-term interruptions Panel PC 800 User's Manual V 1.00...
2 m, criteria B max. 2.5 kV, 1 MHz ±10%, repeat DC power inputs rate 400/seconds, length 2 seconds, connection lengths 2 m, criteria B Table 164: Test requirements - Damped oscillatory waves Panel PC 800 User's Manual V 1.00...
< 20 kg < 20 kg 20 - 100 kg 20 - 100 kg 20 - 100 kg > 100 kg > 100 kg > 100 kg Table 170: Test requirements - Toppling Panel PC 800 User's Manual V 1.00...
Devices with product packaging each with 5 fall tests Weight Height < 10 kg 0.3 m 10 - 40 kg 0.3 m > 40 kg 0.25 m Table 171: Test requirements - Free fall Panel PC 800 User's Manual V 1.00...
Limits according to EN 60068-2-1 EN 61131-2 Dry cold 16 hours at -40°C for 1 cycle, then 1 hour acclimatization and function testing, duration approximately 17 hours Table 175: Test requirements - Dry cold Panel PC 800 User's Manual V 1.00...
EN 60068-2-3 EN 61131-2 Humid heat, constant (storage) 48 hours at +40°C and 92.5% RH, then insulation test within 3 hours, duration approximately 49 hours Table 179: Test requirements - Humid heat, constant (storage) Panel PC 800 User's Manual V 1.00...
1.0 mm² 3.3 V 1.5 mm² 2.6 V 2.5 mm² 1.9 V 4.0 mm² 1.4 V > 6.0 mm² 1.0 V Table 181: Test requirements - Ground resistance Panel PC 800 User's Manual V 1.00...
< 60 V after 5 sec (active parts) < 60 V after 5 sec (active parts) < 60 V after 1 sec (plug pins) < 60 V after 1 sec (plug pins) Table 184: Test requirements - Residual voltage Panel PC 800 User's Manual V 1.00...
Protection against touching Protection against touching dangerous parts with fingers dangerous parts with conductor Protection against water IP.0 IP.5 permeation with damaging Not protected Protection against water jets consequences Table 190: Test requirements - Protection Panel PC 800 User's Manual V 1.00...
This mark is valid for the USA and Canada and simplifies certification of your machines and systems in these areas. Europe All harmonized EN standards for the applicable directives are met. Table 191: International Certifications Panel PC 800 User's Manual V 1.00...
2 x 12 V; 2.2 Ah; for battery unit 9A0100.14 9A0017.01 RS232 Null Modem Cable, 0.6 m To connect UPS and load system (9-pin DSUB socket - 9-pin DSUB socket) Table 192: Model numbers - Accessories Panel PC 800 User's Manual V 1.00...
Page 292
SDL cable for fixed type of layout with one-sided 45° plug; length: 1.8 m 5CASDL.0018-03 SDL flex cable 1.8 m SDL cable for fixed and flexible type of layout; length: 1.8 m Table 192: Model numbers - Accessories Panel PC 800 User's Manual V 1.00...
Page 293
RS232 extension cable for remote operation of a display unit with touch screen; length 5 m. 9A0014.10 RS232 cable DB9/f:DB9/m 10 m RS232 extension cable for remote operation of a display unit with touch screen; length 10 m. Table 192: Model numbers - Accessories Panel PC 800 User's Manual V 1.00...
Features 0AC201.91 4A0006.00-000 Capacity 950 mAh Voltage Self discharge at 23°C < 1% per year Storage time Max. 3 years at 30° C Table 194: Technical data - lithium batteries Panel PC 800 User's Manual V 1.00...
Page 295
Accessories • Replacement CMOS batteries Environment 0AC201.91 4A0006.00-000 Storage temperature -20 to +60°C Relative humidity 0 to 95% (non-condensing) Table 194: Technical data - lithium batteries (cont.) Panel PC 800 User's Manual V 1.00...
Name 0TB103.9 0TB103.91 Number of pins Type of terminal Screw clamps Cage clamps Distance between contacts 5.08 mm Table 196: Technical data - TB103 Panel PC 800 User's Manual V 1.00...
Page 297
Current load according to VDE / UL,CSA 14.5 A / 10 A per contact Terminal size 0.08 mm² - 3.31 mm² Cable type Copper wires only (no aluminum wires!) Table 196: Technical data - TB103 (cont.) Panel PC 800 User's Manual V 1.00...
Model number Description Figure 5AC900.1000-00 Adapter DVI-A/m to CRT DB15HD/f Adapter DVI (plug) to CRT (socket), for connecting a standard monitor to a DVI-I interface. Table 197: Order data - DVI - CRT adapter Panel PC 800 User's Manual V 1.00...
Accessories • USB interface cover (attached) 5. USB interface cover (attached) Front side USB port cap (attached) for Automation Panel 900, Panel PC 700 and Panel PC 800 devices. 5.1 Order data Model number Description Figure 5AC900.1200-01 USB port cap IP65 M20 /2 Front-side USB port cap (attached) knurled, short, not slotted.
Accessories • Uninterruptible power supply 6. Uninterruptible power supply With the optionally integrated UPS, the Panel PC 800 makes sure that the PC system completes write operations even after a power failure occurs. When the UPS detects a power failure, it switches to battery operation immediately without interruption.
2) Add-on UPS module 5AC600.UPSI-00 3) Battery unit 5AC600.UPSB-00 4) UPS connection cable 0.5 m (5CAUPS.0005-00) or 3 m (5CAUPS.0030-00) 5) For info regarding configuration of the B&R UPS using the ADI Control Center. Panel PC 800 User's Manual V 1.00...
Via the ADI Control Center (see section 8 "Automation Device Interface (ADI) - Control Center") Configuration Via the ADI Control Center (see section 8 "Automation Device Interface (ADI) - Control Center") Table 199: Technical data - 5AC600.UPSI-00 Panel PC 800 User's Manual V 1.00...
Page 303
The module is installed using the materials included in the delivery. Connection cable Mounting bracket Spacing bolt (14 mm) Spacing bolt (16 mm) Spacing ring (2 mm) Torx screws (T10) Figure 138: Add-on UPS module 5AC600.UPSI-00 - Installation materials Panel PC 800 User's Manual V 1.00...
Mounting instructions See "Mounting instructions", on page 307 Lifespan 10 years at 25°C (up to 80% battery capacity) Maintenance interval during storage 6 month interval between charges Table 200: Technical data - 5AC600.UPSB-00 Panel PC 800 User's Manual V 1.00...
Page 305
8000 2581 1674 1085 6000 4000 2000 65 70 Temperature [°C] Figure 140: Temperature life span diagram Deep discharge cycles 1000000 100000 10000 1000 Amount of discharge [%] Figure 141: Deep discharge cycles Panel PC 800 User's Manual V 1.00...
Page 306
Accessories • Uninterruptible power supply Dimensions ø5.4 ø11 87.5 All values in mm. Figure 142: Dimensions - 5AC600.UPSB-00 Panel PC 800 User's Manual V 1.00...
Page 307
38.9 126.5 All values in mm. Figure 143: Drilling template for the battery unit Mounting instructions Due to the unique construction of these batteries, they can be stored and operated in any position. Panel PC 800 User's Manual V 1.00...
Peak operating voltage 12 V DC Testing AC voltage Wire / wire 1500 V Operating voltage Max. 300 V Current load 10 A at +20°C Table 201: Technical data - UPS connection cable Panel PC 800 User's Manual V 1.00...
Data and commands are exchanged between the UPS and the load system via the handshake signals for an RS232 interface. More information concerning an external UPS is available in the "UPS manual", which can be downloaded from the B&R homepage (www.br-automation.com). Panel PC 800 User's Manual V 1.00...
To connect UPS and load system (9-pin DSUB socket - 9-pin DSUB socket) 9A0017.02 RS232 Null Modem Cable, 1.8 m To connect UPS and load system (9-pin DSUB socket - 9-pin DSUB socket) Table 202: UPS - Order data Panel PC 800 User's Manual V 1.00...
Page 313
2) The file is written/read sequentially in True IDE mode with the DOS program Thruput.exe. 3) Endurance of B&R CF cards (linear written block size with 128 kB) 4) Depending on the average file size. 5) Not supported by B&R Embedded OS installer. Panel PC 800 User's Manual V 1.00...
MP100/200, PP100/200, PP300/400, PPC300, PPC700, PPC725, PPC800, Provit 2000, Provit 5000, APC620, APC680, APC810, APC820 Windows XP Professional Windows XP Embedded Windows Embedded Standard 2009 Windows CE 6.0 Table 206: Technical data - CompactFlash cards 5CFCRD.xxxx-03 Panel PC 800 User's Manual V 1.00...
Page 318
Max. 1000 g (9810 m/s 0-peak) Storage/Transport Max. 3000 g (29430 m/s 0-peak) Altitude Maximum 80,000 feet (24,383 meters) Table 206: Technical data - CompactFlash cards 5CFCRD.xxxx-03 (cont.) 1) Not supported by B&R Embedded OS installer. Panel PC 800 User's Manual V 1.00...
The following characteristics, features and limit values only apply to this accessory and can deviate those specified for the entire device. For the entire device where this accessory is installed, refer to the data provided specifically for the entire device. Panel PC 800 User's Manual V 1.00...
Page 321
0-peak) and 11 ms length Transport Max. 80 g (784 m/s 0-peak) and 11 ms length Altitude Operation 3,048 meters Bearings 12,192 meters Transport 12,192 meters Table 208: Technical data - USB flash drive 5MMUSB.2048-00 Panel PC 800 User's Manual V 1.00...
Figure 152: Temperature humidity diagram - USB flash drive - 5MMUSB.2048-00 Temperature data is for operation at 500 meters. Derating the max. ambient temperature - typically 1°C per 1000 meters (from 500 meters above sea level). Panel PC 800 User's Manual V 1.00...
11. B&R Automation Studio 3.0USBdongle 11.1 Order data Model number Description Figure 1A4300.LZ1U B&R Automation Studio 3.0 USB dongle Dongle for using AR010. Table 209: Order data - B&R Automation Studio 3.0 Dongle Panel PC 800 User's Manual V 1.00...
• Power Panel 100 BIOS devices • Mobile Panel 100 BIOS devices • Power Panel 100 / Mobile Panel 100 user boot logo • Power Panel 100 / Mobile Panel 100 REMHOST utility Panel PC 800 User's Manual V 1.00...
Page 325
Intel PCI NIC boot ROM • Diagnostics • CompactFlash lifespan calculation for Silicon Systems CompactFlash cards 5CFCRD.xxxx-03 Windows and embedded operating systems • Thin client • Windows CE • Windows NT Embedded • Windows XP Embedded Panel PC 800 User's Manual V 1.00...
Page 326
Acrobat Reader 5.0.5 (freeware in German, English, and French) • Power Archiver 6.0 (freeware in German, English, and French) • Internet Explorer 5.0 (German and English) • Internet Explorer 6.0 (German and English) Panel PC 800 User's Manual V 1.00...
Single cable, DVI-D/m:DVI-D/m; length: 1.8 m 5CADVI.0050-00 DVI-D cable 5 m Single cable, DVI-D/m:DVI-D/m; length: 5 m 5CADVI.0100-00 DVI-D cable 10 m Single cable, DVI-D/m:DVI-D/m; length: 10 m Table 211: Model numbers - DVI cables Panel PC 800 User's Manual V 1.00...
DVI cables provided by B&R are guaranteed to function properly. DVI-D (24+1), male DVI-D (24+1), male Pin assignments DVI-D (24+1), male DVI-D (24+1), male Cable shielding Cable shielding Figure 156: Pin assignments - DVI cable Panel PC 800 User's Manual V 1.00...
SDL cable for a fixed type of layout; length: 25 m 5CASDL.0300-00 SDL cable 30 m SDL cable for a fixed type of layout; length: 30 m Table 213: Model numbers - SDL cables Panel PC 800 User's Manual V 1.00...
SDL cables provided by B&R are guaranteed to function properly. DVI (24+1), male DVI (24+1), male Pin assignments DVI (24+1), male DVI (24+1), male Cable shielding Cable shielding Figure 159: Pin assignments - SDL cable 5CASDL.0xxx-00 Panel PC 800 User's Manual V 1.00...
SDL cable for fixed type of layout with one-sided 45° plug; length: 10 m 5CASDL.0150-01 SDL cable 15 m 45° SDL cable for fixed type of layout with one-sided 45° plug; length: 15 m Table 215: Model numbers - SDL cables with 45° plug Panel PC 800 User's Manual V 1.00...
SDL cables provided by B&R are guaranteed to function properly. DVI (24+1), male DVI (24+1), male Pin assignments DVI (24+1), male DVI (24+1), male Cable shielding Cable shielding Figure 162: Pin assignments - SDL cable with 45° plug 5CASDL.0xxx-01 Panel PC 800 User's Manual V 1.00...
SDL cable for fixed and flexible type of layout; length: 25 m 5CASDL.0300-03 30 m flex SDL cable SDL cable for fixed and flexible type of layout; length: 30 m Table 217: Model numbers - SDL cable 5CASDL.0xxx-03 Panel PC 800 User's Manual V 1.00...
Temperature resistance Fixed installation -20 to +80°C Moving -5 to +60°C Bearings -20 to +80°C Fire resistance Fire resistant according to UL758 (cable vertical flame test) Table 218: Technical data - SDL cable 5CASDL.0xxx-03 Panel PC 800 User's Manual V 1.00...
SDL- TMDS DATA 2/SDL Shield TMDS DATA 2/SDL Shield TMDS Data 2+ TMDS Data 2+ TMDS Data 2- TMDS Data 2- Cable shielding Cable shielding Figure 166: Pin assignments - SDL cable 5CASDL.0xxx-03 Panel PC 800 User's Manual V 1.00...
Gold plated Mechanical protection Metal cover with crimped stress relief Max. tension ≤ 400 N During installation ≤ 50 N During operation Table 221: Technical data - SDL flex cable with extender 5CASDL.0x00-13 Panel PC 800 User's Manual V 1.00...
Page 342
Tested flex radius: 180 mm;15x cable diameter; hub: 460 mm; speed: 4800 cycles / hour Approbation UL AWM 20236 80°C 30 V Oil and hydrolysis resistance According to VDE 0282-10 Table 221: Technical data - SDL flex cable with extender 5CASDL.0x00-13 (cont.) Panel PC 800 User's Manual V 1.00...
• Connect the end labeled "SDL IN" with the video output of the Automation PC 620 or Panel PC 800 (monitor/panel output) or Panel OUT of an AP900 AP Link card. • The "SDL OUT" end should be connected to the display unit (e.g. Automation Panel 900) via the Automation Panel Link insert card (Panel IN).
DVI (24+1), male DVI (24+1), male Extender Unit Black Box Pin assignments DVI (24+1), male DVI (24+1), male Cable shielding Cable shielding Figure 171: Pin assignments - SDL flex cable with extender 5CASDL.0x00-13 Panel PC 800 User's Manual V 1.00...
Entire cable Connector type USB type A male and USB type B male Wire cross section AWG 24, 28 Flexibility Flexible Flex radius Min. 100 mm Table 225: Technical data - USB cables Panel PC 800 User's Manual V 1.00...
If a self-built cable is used, B&R cannot guarantee that it will function properly. The USB cables provided by B&R are guaranteed to function properly. Pin assignments USB type A, male USB type B, male Cable shielding Cable shielding Figure 175: Pin assignments - USB cable Panel PC 800 User's Manual V 1.00...
Page 350
Accessories • Cables Panel PC 800 User's Manual V 1.00...
The evaluated battery status is displayed in the BIOS Setup pages and in the B&R Control Center (ADI driver), but can also be read in a customer application via the ADI Library. Panel PC 800 User's Manual V 1.00...
To make the next battery change easier, be sure the removal strip is in place when inserting battery. • Reconnect power supply to Panel PC 800 (plug in power cable and press power button). • Date and time might need to be reset in BIOS.
1) The measured temperature is a guideline for the immediate ambient temperature, but can be influenced by neighboring components. 2) The B&R Control Center - ADI driver - can be downloaded for free from the download area on the B&R homepage (www.br- automation.com). Panel PC 800 User's Manual V 1.00...
The functions of the MTCX can be expanded via Firmware upgrade in BIOS (menu item "advanced" - baseboard/panel features) or in Microsoft Windows XP/embedded, using B&R Control Center. 1) Can be downloaded from the download area on the B&R homepage (www.br-automation.com). Panel PC 800 User's Manual V 1.00...
For example, slide-in 1: 44°C + 16°C = 60°C --> maximum fan speed The fans are first switched off again if the evaluated temperature remains 6°C lower than the start-up temperature for a time span of 30 minutes (=lag-time). Panel PC 800 User's Manual V 1.00...
4 assignments per key possible (using layer function) • Configuration of panel locking time when multiple Automation Panel 900 devices are connected to Automation PC 620, Panel PC 700 and Panel PC 800 devices Panel PC 800 User's Manual V 1.00...
Page 357
The B&R Key Editor can be downloaded for free from the download area on the B&R homepage (www.br-automation.com). Additionally, it can also be found on the B&R HMI Drivers & Utilities DVD (model number 5SWHMI.0000-00). Panel PC 800 User's Manual V 1.00...
Supported programming languages: Visual Basic, Visual C++ • Online documentation (German, English) • Installation using its own setup Supports following systems: • Automation PC 620 • Automation PC 810 • Automation PC 820 • Panel PC 300 Panel PC 800 User's Manual V 1.00...
The latest version of the B&R Automation Device Interface (ADI) Development Kit can be found in the download area (Service - Material Related Downloads - BIOS / Drivers / Updates) on the B&R homepage (www.br-automation.com). Run Setup.exe to install (e.g. by double-clicking in Explorer). Panel PC 800 User's Manual V 1.00...
Sea water Decon Table 229: Chemical resistance of the décor foil The décor foil conforms to DIN 42115 section 2 for exposure to glacial acetic acid for less than one hour without visible damage. Panel PC 800 User's Manual V 1.00...
6. Viewing angles The viewing angle information of the display types (R, L, U, D) can be seen in the technical data for the individual components. 6 o clock direction Figure 181: Viewing angle definition Panel PC 800 User's Manual V 1.00...
Although BIOS is used to configure a system's performance, the user does not usually come into contact with it. Panel PC 800 User's Manual V 1.00...
Page 363
High reliability using error detection, error handling, troubleshooting. Hamming distance. CD-ROM Abbreviation for "Compact Disc Read-Only Memory". A removable data medium with a capacity of ~700 MB. CD-ROMs are optically scanned. Panel PC 800 User's Manual V 1.00...
Page 364
CF cards were launched by SanDisk back in 1994. Currently, memory capacities reach up to 64 GB per unit. Since 1995, CompactFlash Association [CFA] has been looking after standardization and the worldwide distribution of CF technology Panel PC 800 User's Manual V 1.00...
Page 365
Although it is slower, dynamic RAM is used more often than static RAM since the simple design of the circuits means that it can store four times more data than static RAM. Panel PC 800 User's Manual V 1.00...
Page 366
An abbreviation for "Enhanced Integrated Drive Electronics". An expansion of the IDE standard. Enhanced IDE is considered the standard for hardware interfaces. This interface is designed for drives with an integrated drive controller. Panel PC 800 User's Manual V 1.00...
Page 367
Programs stored permanently in read-only memory. Firmware is software used to operate computer-controlled devices that generally stays in the device throughout its lifespan or over a long period of time. Such software includes operating systems for CPUs and application Panel PC 800 User's Manual V 1.00...
Page 368
An abbreviation for "Hard Disk Drive". Fixed magnetic mass memory with high capacities, e.g. 120 GB. An abbreviation for "Integrated Drive Electronics". A drive interface where the controller electronics are integrated in the drive. Panel PC 800 User's Manual V 1.00...
Page 369
If an electrical field is applied to the electrodes, the molecules align themselves with the field and form crystalline arrangements that polarize the light passing through. A polarization filter, which is arranged using lamellar electrodes, blocks the polarized light. In this way, a cell Panel PC 800 User's Manual V 1.00...
Page 370
An abbreviation for "Mean time between failure". The average time which passes before a hardware component fails and repair is needed. This time is usually expressed in thousands or ten thousands of hours, sometimes known as power-on hours (POH). Panel PC 800 User's Manual V 1.00...
Page 371
It communicates serially with the connection modules via the ISA or PCI bus or Ethernet. It communicates serially with the connection modules via the ISA or PCI bus or Ethernet. Panel A common term for B&R display units (with or without keys). Panel PC 800 User's Manual V 1.00...
Page 372
(generally the monitor). If the POST runs successfully, control is transferred over to the system's bootstrap loader. POWERLINK See "Ethernet POWERLINK". Panel PC 800 User's Manual V 1.00...
Page 373
See also "real-time demands" and "real- time system". An abbreviation for "Read-Only Memory". Semiconductor memory where programs or data were permanently stored during the production process. Panel PC 800 User's Manual V 1.00...
Page 374
PC insert card that has full PLC functionality. On the PC, it is coupled via a DPR with the process using a fieldbus connection. It is programmed externally or using the host PC. Panel PC 800 User's Manual V 1.00...
Page 375
Transmission Control Protocol/Internet Suit of Protocols. Network protocol that has become the generally accepted standard for data exchange in heterogeneous networks. TCP/IP is used both in local networks for communication between various computer and also for LAN to WAN access. Panel PC 800 User's Manual V 1.00...
Page 376
CD drives, printers, modems as well as the mouse and keyboard). This is done by connecting the devices in a row. USB allows devices to be changed when the power supply is switched on (hot plugging) and multi-layered data flow. Panel PC 800 User's Manual V 1.00...
Page 377
An abbreviation for "EXtended Graphics Array". An expanded standard for graphics controllers and monitors that was introduced by IBM in 1990. This standard supports 640x480 resolution with 65,536 colors or 1024x768 resolution with 256 colors. This standard is generally used in workstation systems. Panel PC 800 User's Manual V 1.00...
Page 378
Appendix A • Glossary Panel PC 800 User's Manual V 1.00...
Page 379
ATTO disk benchmark v2.34 - cyclic read............ 104 Figure 43: ATTO disk benchmark v2.34 - cyclic write ........... 104 Figure 44: Hard disk adapter (slide-in compact) 5AC801.ADAS-00......105 Figure 45: Slide-in HDD EE25 5AC801.HDDS-00 ............106 Panel PC 800 User's Manual V 1.00...
Page 381
Creating a USB flash drive for B&R upgrade files........244 Figure 123: Creating a CompactFlash card for B&R upgrade files ......... 246 Figure 124: Panel PC 800 with MS-DOS ................ 247 Figure 125: Windows XP Professional Logo ..............249 Figure 126: Windows XP Embedded Logo..............
Page 382
Figure 178: MTCX controller location ................354 Figure 179: B&R Key Editor screenshots (Version 3.00) ..........356 Figure 180: ADI development kit screenshots (Version 2.40) ......... 358 Figure 181: Viewing angle definition................361 Panel PC 800 User's Manual V 1.00...
Page 383
Table 44: Technical data - 5PC820.1906-00 ..............73 Table 45: Technical data - CPU boards ................78 Table 46: Technical data - Heat sink................... 79 Table 47: Technical data - Main memory ................80 Panel PC 800 User's Manual V 1.00...
Page 385
Table 138: 945GME Power profile setting overview ............227 Table 139: BIOS post code messages BIOS 945GME ............228 Table 140: RAM address assignment ................. 229 Table 141: I/O address assignment ..................230 Panel PC 800 User's Manual V 1.00...
Page 386
Table 185: Test requirements - Leakage current ..............288 Table 186: Test requirements - Overload ................288 Table 187: Test requirements - Defective component ............288 Table 188: Test requirements - Voltage range..............288 Panel PC 800 User's Manual V 1.00...
Page 387
Meaning of battery status OK - Bad ..............352 Table 227: Temperature sensor locations................353 Table 228: Temperature limits of the fan (MTCX PX32 V1.01)........... 355 Table 229: Chemical resistance of the décor foil ..............360 Panel PC 800 User's Manual V 1.00...
Page 388
Table index Panel PC 800 User's Manual V 1.00...