Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for B&R PROVIT 3030
Summary of Contents for B&R PROVIT 3030
- Page 1 PROVIT 3030 USER'S MANUAL Version: 1.0 (April 1992) Model No.: 6F0001.00-020 ARCNET is a registered trademark of Datapoint Corp. MS-DOS is a registered trademark of Microsoft Corp. is a registered trademark of International Business Machines Corp.
- Page 3 CONTENTS...
-
Page 4: Table Of Contents
CONTENTS 1. General Information ........................... 7 1.1 General Information ........................9 1.2 MS-DOS ........................... 10 1.3 Documentation ......................... 10 1.4 Technical Data .......................... 11 2. Install Procedures ........................... 13 2.1 Unpacking ............................15 2.2 Checking the Delivery ........................15 2.3 Before Power-on ..........................16 2.3.1 AC Input Voltage Switch ....................... - Page 5 4.3.4 Parallel Printer Interface ......................38 4.3.5 Keyboard Interface ........................ 38 4.3.6 I/O Port ..........................38 4.3.7 24 VDC Output ........................38 4.3.8 Fan ............................39 4.4 Monitor Module ..........................40 4.4.1 Fuses ............................. 40 4.4.2 Voltage Selection Switch ....................... 40 4.4.3 Power Connection .........................
-
Page 7: General Information
SECTION 1 GENERAL INFORMATION... -
Page 9: General Information
1.1 GENERAL INFORMATION New standards have been set in the areas of industrial quality, flexibility and functionality with the PROVIT 3030 industrial PC. Quality: Front is dust and water proof to IP54 standards (IP65 standards are in development) Soft rubber mounted hard disk for shock absorption High temperature range, software controlled temperature monitoring All boards solidly screw mounted (with board fasteners) Two electrically isolated RS232 interfaces... -
Page 10: Ms-Dos
PROVIT 3030 industrial PC comes with MS-DOS 5.0 in English or German. MS-DOS is delivered in its original package. To date the PROVIT 3030 has MS-DOS 5.0 installed on drive C in English. If a user requires the German version it can be easily installed (see the MS-DOS User's Manual, "Replacing an installed MS-DOS version). -
Page 11: Technical Data
1.4 TECHNICAL DATA Processor Type 80286 80386 SX 80386 DX 80486 Clock frequency 16 MHz 25 MHz 33 MHz 33 MHz Cache 64 KB 64 KB Memory Standard 2 MB 2 MB 4 MB 4 MB Expandible to 4 MB 16 MB 16 MB 16 MB... -
Page 13: Install Procedures
SECTION 2 INSTALL PROCEDURES... -
Page 15: Unpacking
4. Carefully remove all packing material 2.2 CHECKING THE DELIVERY The material used to package the PROVIT 3030 industrial PC has been tested and is an appropriate safeguard against any transporting accidents under normal circumstances. If in spite of these measures damages are noticed, whether to the packing or to the contents, the device may possibly be inoperable. -
Page 16: Before Power-On
2.3.2 POWER CABLE The power cable for PROVIT 3030 is included in the scope of delivery. The connection to the device is made with screw-on connector. The other end is free and can be terminated with a mains plug or direct to a supply line (section 3 "Installation"... -
Page 17: Transport Safety
2.3.3 TRANSPORT SAFETY The PROVIT 3030 industrial PC is constructed of three basic components. A 19" housing, the computer module and the monitor module. Both modules are fixed in place with easy-on/off hand screws and can be simply removed without any tools (Section 3 "Installation" contains more details). For delivery purposes the computer module and the monitor module are held fast with screws in the bottom of the device for transport. -
Page 18: Fan
2.3.5 FAN The fan cover is not installed during transport. Included with the delivery of the PROVIT 3030 is a fan cover, a grill for the fan and an air filter. The filter must only be used in very dusty or dirty conditions. Fan cover... -
Page 19: Installation
SECTION 3 INSTALLATION... -
Page 21: Structure
3.1 STRUCTURE The PROVIT 3030 has a modular structure consisting of: Housing Computer module Monitor module Monitor module Computer module Housing The computer and monitor module are held in place with hand screws and are easily fastened or unfastened by hand without the need of tools. -
Page 22: Computer Module
3.2 COMPUTER MODULE 3.2.1 REMOVAL Before removing the module be sure to pull the power plug. The computer module must always be removed before the monitor module. Unfasten the hand screw (turn to the left) Pull the module out 3.2.2 INSTALLATION The computer module may only be installed or replaced when the monitor module is in place. -
Page 23: Board Installation
3.2.3 BOARD INSTALLATION Removes screws from computer module cover Carefully lift computer module cover and remove protective (three per side) ground cable Remove back cover from slot Longer boards require a board fastener Carefully place card in slot with a gentle push and fasten it in place with a fastening screw Replace and fasten all screws for computer module cover Reconnect ground cable and replace computer module... -
Page 24: Monitor Module
3.3 MONITOR MODULE 3.3.1 REMOVAL Before removing the monitor module, be sure that the power is disconnected. The monitor module can only be removed after the computer module is taken out. Unfasten the computer module hand screws (turn to the left) Remove the computer module Remove the monitor module Unfasten the monitor module hand screws (turn to the left) -
Page 25: Installation
3.3.2 INSTALLATION The monitor module must be installed before the computer module can be set into place. Set the monitor module into the housing and gently push in until it makes contact Fasten monitor module hand screws (turn to the right) Before fastening the hand screw, turn it one or two times to the left. -
Page 26: Housing
3.4.1 HOUSING GASKET If the PROVIT 3030 should be installed in dusty or wet areas the gasket which is delivered with the unit must be in place (e.g. if the unit is installed in a wall). The gasket is slipped over the unit from the rear and moved up to the front frame. -
Page 27: 19" Rack Installation
USER TEMP. Installation: Insert the cage nuts into the 19" rack in positions respective to holes in the PROVIT 3030 frame Remove the monitor and computer modules Place the PROVIT 3030 housing in position in the rack Using the bolts and washers provided fix the unit to the rack... -
Page 28: Wall Installation
3.4.3 WALL INSTALLATION Before installing the PROVIT 3030 in the wall remove the monitor and computer modules. To install the unit in the wall you will need: four M6 screws four M6 washers four contact washers four M6 nuts Be sure that the wall material will hold the 28 kg of the PROVIT 3030. -
Page 29: Screw Covers
3.4.5 AIR CIRCULATION Proper air flow is important for the operation of the PROVIT 3030. The unit has ventilation areas on the left hand side, the rear and the bottom. At least 10 cm space must be left to allow the circulation of air through... -
Page 31: Device Description
SECTION 4 DEVICE DESCRIPTION... -
Page 33: General
4.1.1 MEMORY PROVIT 3030 models 286 and 386 SX both utilize a working memory of 2MB (dynamic RAM). The 386DX and 486 models are standard with 4 MB. Memory can be expanded in 1 MB modules up to 16 MB in slots on the CPU board (Section 6 "Options and Replacements"... -
Page 34: Floppy Disk Drive
4.2.1 FLOPPY DISK DRIVE The PROVIT 3030 industrial PC has a 3.5" floppy disk drive which is accessible from the front. The unit can run double (720 KB) or high (1.44 MB) density diskettes.The drive is made dust and water proof with a sealed door. -
Page 35: Monitor
4.2.3 MONITOR The 14" color monitor is controlled by a VGA card. The resolution and amount of colors depend on the operating mode which is set for the VGA card (e.g. 1024 x 768 for 16 colors or 640 x 480 for 256 colors). The safety glass used for the monitor is glare free, scratch resistant and improves readability. -
Page 36: Keyboard Legend
The label strips are inserted from under the floppy drive flap. There are five sheets of four insertable strips each delivered with the PROVIT 3030. These can be printed on with a laser printer and cut out properly on the lines provided. The strips have punch outs for the key LEDs. -
Page 37: Computer Module
I/O port Hand screw 4.3.1 SLOTS The PROVIT 3030 utilizes five slots for standard PC cards. The slots are numbered 1 - 5 from left to right. The standard configuration upon delivery is: CPU card is in slot 1 RS232 card is in slot 4 VGA card is in slot 5 Slots 1 to 4 are built for long cards while slot 5 can only operate a short card. -
Page 38: Serial Interfaces
8 pin DIN plug (F) (see picture in section 4.3 "Computer module"). 4.3.6 I/O PORT The PROVIT 3030 Industrial PC utilizes five relay outputs and four digital inputs. Inputs and outputs are all fed through a 15 way termination block situated on the rear of the computer module. -
Page 39: Fan
The fan provides a cool air flow. As long as the device is in operation the fan runs. The following fan components are delivered with the PROVIT 3030: a a a a a a a a a a a a a a a a... -
Page 40: Monitor Module
4.4.2 VOLTAGE SELECTION SWITCH The PROVIT 3030 industrial PC can be switched from 220 VAC to 120 VAC for use in different areas. The switch is set to 220 VAC as a standard for delivery. Before starting up be sure to check for the proper voltage selection depending on the area of the world that you are in. -
Page 41: Monitor Settings
4.4.4 MONITOR SETTINGS Horizontal and vertical positions as well as brightness and contrast can be set with four potentiometers on the rear side of the monitor module (see picture in section 4.4). When the settings are complete the adjustment knobs can be removed to prevent unwanted adjusting. 4.4.5 GROUND CONNECTION An additional ground connection can be made on the rear of the monitor module with the ground termination screw (see picture in section 4.4). -
Page 43: Software
SECTION 5 SOFTWARE... -
Page 45: B&R Utility Diskette
Be careful of the effect that setting the relay output could have on the device currently connected. 5.2 I/O PORTS The PROVIT 3030 industrial PC has two I/O ports which are addressed by addresses $300 to $307. I/O PORT 1... -
Page 46: Key Leds
5.2.1 KEY LEDs Both I/O ports are utilized for key LED control. User key LEDs are controlled through port one. Address $300 $300 $300 $300 $300 $300 $300 $300 $301 $301 $301 $301 $301 $301 $301 $301 Function keys are controlled through I/O port two: Address Address Address... -
Page 47: User Led
5.2.2 USER LED The user LED is controlled through I/O port two (address $306, Bit 7). User-LED POWER USER TEMP. 5.2.3 DIGITAL INPUTS The status of all four digital inputs can be read from the following addresses. Input Input Input Address Address Address... -
Page 48: Temperature Monitoring
5.2.5 TEMPERATURE MONITORING The flow of cool air from the fan follows a predefined course through the device: Hard disk Floppy disk drive Boards Air vents The temperature inside of the device is monitored by two sensors. Sensor number one keeps track of the cool air before it gets to the boards and sensor number two watches the temperature of the air on its way out through the vents. -
Page 49: Addresses And Interrupts
5.3 ADDRESSES AND INTERRUPTS 5.3.1 ADDRESSES PROVIT 3030 industrial PC addresses correspond with an AT personal computer, with the exception of I/O ports. The I/O ports used addresses $300 to $307. Addresses $308 to $31F are used for looking at prospective function expansion and should not be used by the user. -
Page 51: Options And Replacements
SECTION 6 OPTIONS AND REPLACEMENTS... -
Page 53: Keyboard Case
6.1 KEYBOARD CASE A standard AT keyboard can be connected to the keyboard interface on the PROVIT 3030. B&R offers an optional AT keyboard in a protective industrial case. The keyboard case is built for installation in a 19" cabinet or it can be mounted in a wall mount situation. The keyboard pulls out of the frame on rails with angle adjustment to allow for easier keyboard access. -
Page 54: Vga Card
To program MINICONTROL, M264, MIDICONTROL, or MULTICONTROL PLC systems with the B&R PROVIT 3030 an on-line interface module is required to communicate with the PLC processor (Model No. BRIFPC-0). The on-line interface module has two TTY interfaces for programming two PLC processor modules simultaneously. -
Page 55: Replacement Parts
6.8 REPLACEMENT PARTS Item Item Item Item Item Consisting of Consisting of Consisting of Consisting of Consisting of Model No. Model No. Model No. Model No. Model No. B&R utility diskette 1C0110.01-310 Utilities 4 screws M6, 4 nuts M6, 4 washers M6, 4 contact washers M6, 5A0000.00-011 4 cage nuts M6, 4 screw covers, fan cover, fan grill, air filter 5 card holders, 4 potentiometer adjustment knobs, housing gasket... -
Page 57: B&R Sales And Service
B&R SALES AND SERVICE... - Page 58 AUSTRIA TECHNICAL OFFICES IN GERMANY B&R Headquarters (1979) Sales, Applications, Training Development, Production, Sales, Applications, Training TB Bayern TB Südwest Freisinger Str. 34 Friedrich-Dürr-Str. 70 Bernecker + Rainer D-8045 Ismaning D-7100 Heilbronn Industrie-Elektronik Ges.m.b.H. Tel: 089 / 996554-0 Tel: 07131 / 5971-0 A-5142 Eggelsberg 120 Fax: 089 / 996554-99...
- Page 59 INDIA SINGAPORE B&R Representative B&R Representative Sales, Applications, Training Sales, Applications, Training Address, telephone and fax numbers SUMBER CO. PTE. LTD on request 1 & 3, Jalan Kilang Barat Singapore 0315 Tel: 65 / 2716086 Fax: 65 / 2784521 ITALY SLOWENIA B&R Subsiduary (1987) B&R Representative...
- Page 60 UKRAINE B&R Representative Sales, Applications, Training SKIF ENGINEERING 50 Zhovtea avenue, 106 274018 Tchernovtzy Tel: 3-90-69, 4-89-97 Fax: 03722 / 48994 B&R Subsiduary (1987) Sales, Application, Training B&R Industrial Automation Corp. 1325 Northmeadow Parkway Suite 130 Roswell, Georgia 30076 Tel: 404 772-0400 Fax: 404 772-0243...
-
Page 61: Index
INDEX... - Page 62 Symbol 24 VDC output 38 Ground connection 41 Ground screw 41 Ground termination 41 Access time 11 Addresses 49 Air circulation 29 Air flow 29 AT-keyboard 53 Hand screws 17, 21 Hard disk 11, 34, 45, 48 Height 11 Housing 21, 26 Housing gasket 26, 55 Humidity 11 Cache 11...
- Page 63 RS232 card 37, 38, 53 Memory 11, 33, 54 RS232 interfaces 38, 53 Memory expansion 54 Memory expansion modules 54 Memory modules 33 Mode register 45 Sales and service 57 Model numbers 11 Screw covers 29 Monitor 11, 35, 37, 41, 54 Serial interfaces 38 Monitor colors 45 Slots 11, 37...