Lightware MMX8x4-HT420M User Manual page 163

   
8. LW3 Programmers' Reference
Event Manager Tool Kit
Setting the Delay
SET·/EVENTS/E<loc>.ConditionTimeout=<time>
ç
SET·/EVENTS/E<loc>.ConditionEndCheck=<true/false>
ç
SET·/EVENTS/E<loc>.ConditionTimeoutContinuous=<true/false>
ç
Setting the Name of the Event
SET·/EVENTS/E<loc>.Name=<string>
ç
Enable the Event
SET·/EVENTS/E<loc>.Enabled=<true/false>
ç
Triggering a Condition
ç CALL·/EVENTS/E<loc>:triggerCondition(1)
Querying the Condition Counter
ç GET·/EVENTS/E<loc>.ConditionCount
Querying the Condition Trigger Counter
ç GET·/EVENTS/E<loc>.ExternalConditionTriggerCount
Testing an Action
ç CALL·/EVENTS/E<loc>:ActionTest(1)
Variable-Management
Value Assignment
SET·/CTRL/VARS/V<loc>.Value=<value>
ç
Addition and Subtraction (Add Method)
ç CALL·/CTRL/VARS/V<loc>:add(<operand>;<min>;<max>)
Addition and Subtraction (Cycle Method)
ç CALL·/CTRL/VARS/V<loc>:cycle(<operand>;<min>;<max>)
Value Change with Intervals (Case)
CALL·/CTRL/VARS/V<loc>:case(<min> <max>
ç
Scan and Store
ç CALL·/CTRL/VARS/V<loc>:scanf(<path>.<property>;<pattern>)
Reformatting a Value
ç CALL·/CTRL/VARS/V<loc>:printf(<prefix>%s<postfix>)
MMX8x4-HT series – User's Manual
<val>;)
Applied firmware package: v1.3.0 | LDC software: v2.4.2
Ethernet Tool Kit
Device Filter Based on MAC Address
SET·/MANAGEMENT/MACFILTER.MACaddress<loc>=<MAC_address>;<receive>;<send>;<name>
ç
LW2 Control Port Blocking
SET·/MANAGEMENT/SERVICEFILTER.Lw2Enabled=<port_mode>
ç
HTTP Port Blocking
SET·/MANAGEMENT/SERVICEFILTER.HttpEnabled=<port_mode>
ç
HTTP Post Receiving Blocking
SET·/MANAGEMENT/SERVICEFILTER.HttpEnabled=<port_mode>
ç
Powering on a Computer over Ethernet (Wake-on-LAN)
ç CALL·/MEDIA/ETHERNET:wakeOnLan(MAC_address)
Relay Port Configuration
Set Relay Connection Status
SET·/MEDIA/RELAY/<relay_port>.Output=<relay_status>
ç
GPIO Port Settings
Set the Direction of a GPIO Pin
SET·/MEDIA/GPIO/<gpio_port>.Direction=<dir>
ç
Set the Output Level of a GPIO Pin
SET·/MEDIA/GPIO/<gpio_port>.Output=<value>
ç
Toggle the Level of a GPIO Pin
ç CALL·/MEDIA/GPIO/<gpio_port>:toggle()
USB Port Settings
USB Host Select
SET·/MEDIA/USB/USBSWITCH.HostSelect=<USB_host>
ç
Power Switch Delay
SET·MEDIA/USB/USBSWITCH.DelayedSwitch=<delay_status>
ç
Host 5V Sense
GET·/MEDIA/USB/USBSWITCH.<HostPc>
ç
Device 5V Enable
SET·/MEDIA/USB/USBSWITCH.<Device5vEnable>=<enable>
ç
Query the 5V Overcurrent status of the Device
GET·/MEDIA/USB/USBSWITCH.<deviceid>
ç
163