Lightware MMX8x4-HT420M User Manual page 160

   
8. LW3 Programmers' Reference
Set the Duck on the Emb. Audio In
SET·/MEDIA/AUDIO/I11.Ducker=<duck_status>
ç
Set the Highpass Filter on the Emb. Audio In
SET·/MEDIA/AUDIO/I11.HPF=<hpf_status>
ç
Set the Lowpass Filter on the Emb. Audio In
SET·/MEDIA/AUDIO/I11.LPF=<lpf_status>
ç
Equalizer (EQ) Settings on the Emb. Audio In
SET·/MEDIA/AUDIO/I11.<eq_nr>Gain=<gain_value>
ç
Advanced Analog Audio Output
Mute the Analog Audio Out
SET·/MEDIA/AUDIO/O6.Mute=<mute_status>
ç
Set the Volume with Exact Value on Analog Audio Out
SET·/MEDIA/AUDIO/O6.Volume=<volume_dB>
ç
Set the Volume by Step Value - Volume up
ç CALL·/MEDIA/AUDIO/O6:volumeUp()
Set the Volume by Step Value - Volume down
ç CALL·/MEDIA/AUDIO/O6:volumeDown()
Set the Balance on Analog Audio Out
SET·/MEDIA/AUDIO/O6.Balance=<bal_set>
ç
Set the Phase Invert on Analog Audio Out
SET·/MEDIA/AUDIO/O6.InvertPhase=<invertphase_status>
ç
Set the Mono Function on Analog Audio Out
SET·/MEDIA/AUDIO/O6.Monomix=<mono_status>
ç
Set the Delay on Analog Audio Out
SET·/MEDIA/AUDIO/O6.Delay=<delay_status>
ç
Set the Delay Time on Analog Audio Out
SET·/MEDIA/AUDIO/O6.Delay=<delay_time>
ç
Equalizer (EQ) Settings on Analog Audio Out
SET·/MEDIA/AUDIO/O6.<eq_nr>Gain=<gain_value>
ç
Audio Presets
Save a Preset
ç CALL /PRESETS/MICADDON/<ch>:savePreset(<index>,<target_node>,<name>)
MMX8x4-HT series – User's Manual
Load a Preset
ç CALL /PRESETS/MICADDON/<ch>:loadPreset(<index>,<target_node>)
Delete a Preset
ç CALL·/PRESETS/MICADDON/<ch>:deletePreset(<index>)
Audio Scenes
Change the Scene Name
SET·/PRESETS/MICADDON/SCENES/<scene_id>.Name=<scene_name>
ç
Save a Scene
ç CALL·/PRESETS/MICADDON/SCENES:saveScene(<index>,I9,I10,I11,O6,<scene_name>)
Load a Scene
ç CALL·/PRESETS/MICADDON/SCENES:loadScene(<index>,I9,I10,I11,O6)
Delete a Scene
ç CALL·/PRESETS/MICADDON/SCENES:deleteScene(<index>)
Serial Port Configuration
Protocol Setting
SET·/MEDIA/UART/<serial_port>.ControlProtocol=<cont_protocol>
ç
BAUD Rate Setting
SET·/MEDIA/UART/<serial_port>.Baudrate=<baudrate>
ç
Operation Mode Setting
SET·/MEDIA/UART/<serial_port>.Rs232Mode=<rs232_mode>
ç
Command Injection Mode
SET·/MEDIA/UART/<serial_port>.CommandInjectionEnable=<ci_stat>
ç
Query the RS-232 Command Injection Port Number
ç GET·/MEDIA/UART/<serial_port>.CommandInjectionPort
Serial Port Messaging
Sending a Message (ASCII-format) via RS-232
ç CALL·/MEDIA/UART/P1:sendMessage(<message>)
Sending a Text (ASCII-format) via RS-232
ç CALL·/MEDIA/UART/P1:sendText(<message>)
Sending a Binary Message (HEX-format) via RS-232
ç CALL·/MEDIA/UART/P1:sendBinaryMessage(<message>)
Applied firmware package: v1.3.0 | LDC software: v2.4.2
160