Embedded Audio Input Settings - Lightware MMX8x4-HT420M User Manual

   
8. LW3 Programmers' Reference
8.10.2.8. Set the Phase Invert on Advanced Analog In
Command and Response
SET·/MEDIA/AUDIO/I10.InvertPhase=<invertphase_status>
ç
pw·/MEDIA/AUDIO/I10.InvertPhase=<invertphase_status>
æ
Parameters
<invertphase_status> true: Invert phase is on;
false: Invert phase is off.
Example
ç SET /MEDIA/AUDIO/I10.InvertPhase=true
æ pw /MEDIA/AUDIO/I10.InvertPhase=true
For more details about the Phase Invert feature see the
8.10.2.9. Set the Highpass Filter on Advanced Analog In
Command and Response
SET·/MEDIA/AUDIO/I10.HPF=<hpf_status>
ç
pw·/MEDIA/AUDIO/I10.HPF=<hpf_status>
æ
Example
ç SET /MEDIA/AUDIO/I10.HPF=true
æ pw /MEDIA/AUDIO/I10.HPF=true
<hpf_status> true: Highpass filter is on.
false: Highpass filter is off.
For more details about the Highpass Filter
8.10.2.10. Set the Lowpass Filter on Advanced Analog In
Command and Response
SET·/MEDIA/AUDIO/I10.LPF=<lpf_status>
ç
pw·/MEDIA/AUDIO/I10.LPF=<lpf_status>
æ
Parameters
<lpf_status> true: Lowpass filter is on.
false: Lowpass filter is off.
Example
ç SET /MEDIA/AUDIO/I10.LPF=true
æ pw /MEDIA/AUDIO/I10.LPF=true
For more details about the Lowpass Filter
Advanced Analog Input Channel
see the Advanced Analog Input Channel section.
see the Advanced Analog Input Channel section. .
Applied firmware package: v1.3.0 | LDC software: v2.4.2
MMX8x4-HT series – User's Manual
8.10.2.11. Equalizer (EQ) Settings on Advanced Analog In
Command and Response
SET·/MEDIA/AUDIO/I10.<eq_nr>Gain=<gain_value>
ç
pw·/MEDIA/AUDIO/I10.<eq_nr>Gain=<gain_value>
æ
Parameters
Identifier
<eq_nr>
<gain_value>
Example
section.
ç SET /MEDIA/AUDIO/I10.PEQ1Gain=-16
æ pw /MEDIA/AUDIO/I10.PEQ1Gain=-15.00
For more details, see
8.10.3. Embedded Audio Input Settings

INFO: Embedded audio input setting commands are available in MMX8x4-HT400MC and
MMX8x4-HT420M model. The settings refer to the chosen embedded audio channel in the audio mixer.
See more details in
8.10.3.1. Set the Audio Channel
Command and Response
SET·/MEDIA/AUDIO/I11.AudioSource=<in><a_v>
ç
pw·/MEDIA/AUDIO/I11.AudioSource=<in><a_v>
æ
Parameters
<a_v> A: Embed from AUX audio
V: HDMI audio
Example
ç SET /MEDIA/AUDIO/I11.AudioSource=I5A
æ pw /MEDIA/AUDIO/I11.AudioSource=I5A
Embedded analog audio of I5 port is chosen.

ATTENTION!
Parameter values
PEQ1: Low (100 Hz)PEQ2: Lmid (400 Hz)
PEQ3: Hmid: (1.6 kHz)
PEQ4: High: (8 kHz)
The EQ gain value can be set between -18dB and +18dB, in step of 3.00 dB. The value is rounded
down if necessary to match with the step value. For more details, see
Equalization (EQ) Settings.
Audio Interface section.
This setting affects to the crosspoint state.
123
Equalization (EQ) Settings.