Lightware MMX8x4-HT420M User Manual page 161

   
8. LW3 Programmers' Reference
RS-232 Message Recognizer
Enable the Recognizer
SET·/MEDIA/UART/<serial_port>.RecognizerEnable=<recognizer_enable>
ç
Set the Delimiter Hex
SET·/MEDIA/UART/RECOGNIZER.DelimiterHex=<delimiter>
ç
Set the Timeout
SET·/MEDIA/UART/RECOGNIZER.TimeOut=<timeout>
ç
Querying the Last Recognized Message (String)
ç GET·/MEDIA/UART/RECOGNIZER.Rx
Querying the Last Recognized Message(Hex)
ç GET·/MEDIA/UART/RECOGNIZER.RxHex
Clearing the Last Recognized Stored Message
ç CALL·/MEDIA/UART/RECOGNIZER:clear()
Querying the Last Recognized Active Message (String)
ç GET·/MEDIA/UART/RECOGNIZER.ActiveRx
Querying the Last Recognized Active Message (Hex)
ç GET·/MEDIA/UART/RECOGNIZER.ActiveRxHex
Set the Active Timeout
SET·/MEDIA/UART/RECOGNIZER.ActivePropertyTimeout=<a_timeout>
ç
Running an Immediate Event Action
SET·/MEDIA/UART/RECOGNIZER.ActionTrigger=<event_nr>
ç
IR Port Configuration
Enable the IR Port
SET·/MEDIA/IR/<ir_port>.Enable=<ir_port_staus>
ç
Query the IR Command Injection Port Number
ç GET·/MEDIA/IR/<ir_port>.CommandInjectionPort
IR Port Messaging
Sending Pronto Hex Codes in Little-endian Format
ç CALL /MEDIA/IR/<ir_port>:sendProntoHex(<hex_code>)
Sending Pronto Hex Codes in Big-endian Format
ç CALL /MEDIA/IR/<ir_port>:sendProntoHexBigEndian(<hex_code>)
MMX8x4-HT series – User's Manual
Ethernet Configuration
Query the Current IP Address
ç GET·/MANAGEMENT/NETWORK.IpAddress
Query the Current DHCP Status
ç GET·/MANAGEMENT/NETWORK.DhcpEnabled
Set a Dynamic IP Address
SET·/MANAGEMENT/NETWORK.DhcpEnabled=<dhcp_status>
ç
Set a Static IP Address
SET·/MANAGEMENT/NETWORK.StaticIpAddress=<IP_address>
ç
Change the Subnet Mask (Static)
SET·/MANAGEMENT/NETWORK.StaticNetworkMask=<netmask>
ç
Change the Gateway Address (Static)
SET·/MANAGEMENT/NETWORK.StaticGatewayAddress=<gw_address>
ç
Apply Network Settings
ç CALL·/MANAGEMENT/NETWORK:ApplySettings(1)
Ethernet Message Sending
Sending a TCP Message (ASCII-format)
ç CALL·/MEDIA/ETHERNET:tcpMessage(<IP_address>:<port_no>=<message>)
Sending a TCP Text (ASCII-format)
ç CALL·/MEDIA/ETHERNET:tcpText(<IP_address>:<port_no>=<text>)
Sending a TCP Binary Message (HEX-format)
ç CALL·/MEDIA/ETHERNET.tcpBinary(<IP_address>:<port_no>=<HEX_message>)
Sending UDP Message (ASCII-format)
ç CALL·/MEDIA/ETHERNET:udpMessage(<IP_address>:<port_no>=<message>)
Sending a UDP Text (ASCII-format)
ç CALL·/MEDIA/ETHERNET:udpText(<IP_address>:<port_no>=<text>)
Sending a UDP Binary Message (HEX-format)
ç CALL·/MEDIA/ETHERNET:udpBinary(<IP_address>:<port_no>=<HEX_message>)
TCP Message Recognizer
Setting the IP Address of the TCP Server
ç SET·/CTRL/TCP/C<loc>.ServerIP(<IP_address>)
Applied firmware package: v1.3.0 | LDC software: v2.4.2
161