Lightware MMX4x2-HDMI Quick Start Manual

Quick Start Guide

MMX4x2-HDMI
MMX4x2-HT200
Important Safety Instructions
Please read and keep the information in the attached safety instructions supplied with the
product before you start using the device.
Introduction
Thank You for choosing Lightware MMX4x2 series device. The product is a uniquely mini size
matrix switcher with additional Lightware developments. Audio can be de-embedded from the
HDMI signal to a balanced 5-pole Phoenix (Euroblock) port and external audio signal can
be embedded into the HDMI stream from another 5-pole Phoenix input port. The device has
a built-in Event Manager configurable via the Lightware Device Controller software. Further
control options are served by the USB, RS-232, IR (in and out) and Ethernet ports.
The MMX4x2-HT200 matrix is compatible with any third-
party HDBaseT device.
TM
HDBaseT and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
TM
Compatible Devices
MMX4x2-HT200 matrix is compatible with other Lightware TPS devices, matrix TPS and TPS2
boards, 25G boards, as well as third-party HDBaseT-extenders, but not compatible with the
phased out TPS-90 extenders.
Box Contents
Matrix unit 12V DC adaptor with Phoenix Combicon 3-pole
interchangeable plugs connector
Phoenix Combicon 5-pole Infrared detector unit Infrared emitter unit
connector (2x)
UTP patch cable (3 m) Safety and warranty info,
Quick Start Guide
Front View
1 2 3 4 5 6 7 8 9
1 Audio input port 5-pole Phoenix connector for balanced analog audio.
Infrared connectors 2 x 3.5mm jack (TS/TRS) connectors for Infrared units
2
(IR IN for the detector, IR OUT for the emitter).
USB connector USB interface for LDC connection to control and
3
configure the device.
RS-232 connector 3-pole Phoenix connector for serial communication.
4
Ethernet connector RJ45 connector for control and firmware upgrade purpose.
5
Status LEDs LEDs give feedback about current status of the unit.
6
7 Video select button Pushing the button selects video source for Output 1.
for Output 1
Input select LEDs LEDs give feedback about current crosspoint settings.
8
Video select button Pushing the button selects video source for Output 2.
9
for Output 2
q Reset button Pushing the button reboots the unit.
Set Audio Config button Audio configuration selector and special function button.
w
Front Panel LEDs
LIVE
ƒ OFF: device is not powered.
ƒ BLINKING (slow; 1 sec): device is powered and operational.
ƒ BLINKING (fast; 0,5 sec): device is in bootload mode.
ƒ ON: device is powered but not operational.
AUDIO OUT
ƒ OFF: embedded audio is not present or muted.
ƒ BLINKING: embedded audio format is not supported for audio de-embedding.
ƒ ON: embedded audio is present and de-embedded.
OUT 1 AUTO
ƒ ON: Autoselect is enabled on HDMI Output 1.
OUT 2 AUTO
ƒ ON: Autoselect is enabled on HDMI Output 2.
Crosspoint Status LEDs (OUT 1 and OUT 2)
ƒ ON (green): input is selected, signal is present.
ƒ BLINKING (green): input is selected, signal is not present.
ƒ BLINKING (amber): Audio configuration #1..4 is selected, see details in Front Panel
Operation section.
 Front view is exactly the same for both models.
Mounting
To mount the matrix Lightware supplies optional accessories for different usage. There are
two kinds of mounting kits with similar fixing method. The matrix switcher has two mounting
holes with inner thread on the bottom side. Fasten the device by the screws enclosed to the
accessory.
Under-desk double mounting kit 1U high rack shelf
The Under-desk double mounting kit makes easy to mount a single device on any flat surface,
e.g. furniture. 1U high rack shelf provides mounting holes for fastening two half-rack or four
quarter-rack sized units. Pocket-sized devices can also be fastened on the shelf. To order
mounting accessories please contact sales@lightware.com.
 Using different (e.g. longer) screws may cause damage to the device.
 The matrix is half-rack sized.
Locking DC Plug
Twist 90° clockwise to lock.
Rear View - MMX4x2-HT200
qw 1 2 3
Rear View - MMX4x2-HDMI
1 3
12V DC input 12V DC input for local powering.
1
connector
2 TPS input port TPS input port for compatible transmitter device (extender
/ matrix / board).
HDMI input ports HDMI input ports for sources. Applied cable shall not be
3
more than 20 m (22AWG) when signal resolution is 4K.
HDMI output ports HDMI output ports for sink devices.
4
Audio output port 5-pole Phoenix connector for balanced analog audio.
5
Rear Panel LEDs
TPS link LED - for MMX4x2-HT200 only
OFF: No TPS link.
BLINKING: Device is in low power or Ethernet fallback mode.
ON: TPS link is live.
HDMI Inputs - SIGNAL LED
ƒ OFF: signal is not present on input.
ƒ ON: signal is present on input.
HDMI Outputs - SIGNAL LED
ƒ OFF: output signal is not present or muted.
ƒ ON: signal is present.
HDMI Outputs - HDCP LED
ƒ OFF: output signal is not HDCP-encrypted.
ƒ BLINKING: non-HDCP capable device is connected, encrypted signal is replaced with
red screen.
ƒ ON: output signal is HDCP-encrypted.
Types of IR connectors (1/8" TRS / TS)
3 pole, 2 rings: IR receiver 2 pole, 1 ring: IR transmitter
Compact Size Matrix Concept
MMX4x2 series device is a multifunctional audio/video matrix switcher with four inputs and
two outputs. The HT200 model is built with HDBaseT TM (TPS) technology. The device can be
controlled over various interfaces, e.g. Ethernet, USB, RS-232, and Infrared. The matrix is built
with audio embedder and de-embedder functions.
INPUT
HDMI
Ethernet
TPS
RS-232
OUT OUT
Infrared AUDIO IN CONTROL RS-232 LIVE IN 1 RESET
AUDIO OUT IN 2
OUT 1 AUTO IN 3
OUT 2 AUTO IN 4
L R IR IN IR OUT TX RX LAN OUT 1 OUT 2
VIDEO SELECT VIDEO SELECT
HDMI
Analog audio
+ Local USB
+ Ethernet
+ RS-232
+ Infrared
 Only MMX4x2-HT200 model has TPS input. MMX4x2-HDMI model has HDMI + analog
audio input and HDMI + analog audio outputs.
Connecting Steps
4 5
IR unit
Media player Audio amplifier
IR Audio
4 5
CATx
Compatible
transmitter or
LAN
output board
Ethernet
CATx
For MMX4x2-HT200 only: connect the matrix and the TPS transmitter by a
CATx cable via the TPS connectors.
HDMI
Connect the matrix and the source devices (e.g. Blu-ray player) using the
HDMI inputs and HDMI cables.
HDMI
Connect the sink devices to the HDMI output port by HDMI cables.
Audio
Optionally for analog output connect an audio device (e.g. audio amplifier) to
the analog audio output port by an audio cable.
Audio
Optionally for audio extension: connect the audio source (e.g. media player)
to the audio input port by an audio cable.
IR
Optionally for Infrared extension:
ƒ Connect the IR emitter to the IR OUT port of the matrix, and/or
ƒ Connect the IR detector to the IR IN port of the matrix.
LAN
Optionally connect the matrix to a LAN in order to control the device.
RS-232
Optionally for RS-232 extension: connect a controller/controlled device (e.g.
touch panel) to the RS-232 port.
Power
Connect the power adaptor to the DC input on the matrix first, then to the
AC power socket.
 Powering on the devices is recommended to do as the final step during the installation.
Further Information
The document is valid with the following firmware version: 1.2.0
The product brief and further information are available on www.lightware.com.
See the Downloads
OUTPUT
sales@lightware.com
HDMI
support@lightware.com
Analog audio
SET AUDIO
CONFIG
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Projector Blu-ray player
Audio HDMI HDMI
MMX4x2 series
OUT OUT
AUDIO IN CONTROL RS-232 LIVE IN 1 RESET matrix
AUDIO OUT IN 2
OUT 1 AUTO IN 3
OUT 2 AUTO IN 4
OUT 1 OUT 2 SET AUDIO
L R IR IN IR OUT TX RX LAN VIDEO SELECT VIDEO SELECT CONFIG
RS-232 Power
Power adaptor
Touch panel
section on the website of the product.
Contact us
+36 1 255 3800
+36 1 255 3810
Doc. ver.: 1.1
19200068