Danfoss VLT FC 100 Series Programming Manual page 42

Parameter Description
1-06 Clockwise Direction
This parameter defines the term "Clockwise" corresponding to
the LCP direction arrow. Used for easy change of direction of
shaft rotation without swapping motor wires. (Valid from SW
version 5.84)
Option:
[0] Normal
*
[1] Inverse
NOTE!
This parameter cannot be changed while the motor is
running.
3.3.2 1-10 - 1-13 Motor Selection
NOTE!
This parameter group cannot be adjusted while the motor
is running.
The following parameters are active ('x') depending on the
setting of 1-10 Motor Construction
1-10 Motor construction
1-00 Configuration mode
1-03 Torque Characteristics
1-06 Clockwise direction
1-14 Damping gain
1-15 High pass filter damp time low
speed
1-16 High pass filter damp time
high speed
1-17 Machine voltage filter time
1-20 Motor power [KW]
1-21 - Motor power [HP]
1-22 Motor Voltage
1-23 Motor frequency
1-24 Motor current
1-25 Motor Nom. speed
1-26 Motor rated torque
1-28 Motor rotation check
1-29 AMA
1-30 RS
1-31 Rr
®
VLT HVAC Drive Programming Guide
Function:
Motor shaft will turn in clockwise
direction when the Adjustable
frequency drive is connected U ->
U; V -> V, and W -> W to motor.
Motor shaft will turn in counter
clockwise direction when the
Adjustable frequency drive is
connected U -> U; V -> V, and W -
> W to motor.
[0] [1] PM Motor
Asynchron non-salient
x x
x
x x
x
x
x
x
x
x
x
x
x x
x x
x
x x
x
x x
x
MG11CD22 - VLT ® is a registered Danfoss trademark
1-10 Motor construction
1-35 Xh
1-37 Ld
1-38 Lq
1-39 Motor poles
1-40 Back EMF
1-50 Motor Magnet. at 0 speed
1-51 Min Speed norm. magnet [rpm]
1-52 Min Speed norm. magnet [Hz]
1-58 Flystart test pulses current
1-59 Flystart test pulses frequency
1-60 Low Speed Load Compensation
1-61 High Speed Load Compen-
sation
1-62 Slip Compensation
1-63 Slip Compensation time const.
1-64 Resonance Damping
1-65 Resonance Damping time
const.
1-66 Min Current at low speed
1-70 PM Start mode
1-71 Start Delay
1-72 Start Function
1-73 Flying Start
1-77 Compressor Max Start speed
[rpm]
1-78 Compressor Max Start speed
[Hz]
1-79 Compressor start max time to
trip
1-80 Stop Function
1-81 Min Speed funct. at stop [rpm]
1-82 Min Speed funct. at stop [Hz]
1-86 Trip speed low [rpm]
1-87 Trip speed low [Hz]
1-90 Motor Thermal Protection
1-91 Motor External Fan
1-93 Thermistor Resource
2-00 DC Hold current
2-01 DC Brake current
2-02 DC Braking Time
2-03 DC Brake Cut-In Speed [rpm]
2-04 DC Brake Cut-in Speed [Hz]
2-06 Parking Current
2-07 Parking Time
2-10 Brake Function
2-11 Brake Resistor
2-12 Braking Energy Limit
2-13 Braking Energy Monitoring
2-15 Brake Check
2-16 AC Brake Max Current
[0] [1] PM Motor
Asynchron non-salient
x
x
x x
x
x
x
x
x x
x x
x
x
x
x
x
x
x
x
x x
x x
x x
x
x
x
x x
x x
x x
x x
x x
x x
x x
x x
x
x x
x
x
x
x
x
x x
x x
x x
x x
x x
x
3-15
3 3