WEG CFW-11 Programming Manual page 173

P0263
Functions
(DI1)
Speed/Torque 15
JOG+ 16
JOG- 17
No Ext. Alarm 18
No Ext. Fault 19
Reset 20
PLC Use 21
Manual/Auto 22
Disable FlyStart 24
DC Link Regul. 25
Program. Off 26
Load User 1/2 27
Load User 3 28
DO2 Timer 29
DO3 Timer 30
Trace Function 31
* Factory setting
Proprieties:
Access groups 07 I/O CONFIGURATION
via HMI:
Description:
Those parameters make it possible to configure the functions of the digital inputs, according to the listed range.
Some notes regarding the Digital Input functions are presented next.
- Run/Stop: In order to assure the correct operation of this function, it is necessary to program P0224 and/or
P0227 in 1.
- Increase E.P . and Decrease E.P . (Electronic Potentiometer): They are active when +24 V is applied (for Increasing
E.P .) or 0 V (for Decreasing E.P .) at the respective input programmed for that function. It is also necessary to
program P0221 and/or P0222 in 7. Refer to the section 12.5.
- Local/Remote: When programmed, this function activates "Local" when 0 V is applied to the input, and "Remote"
when +24 V are applied. It is also necessary to program P0220=4 (DIx).
- Speed/Torque: This function is valid for P0202=3 or 4 (Sensorless Vector Control or Vector with Encoder), and
"Speed" is selected with 0 V applied to the input, whereas "Torque" by applying 24 V.
When Torque is selected, the speed regulator parameters P0161 and P0162 become inactive (*). Thus the Total
Reference becomes the Torque Regulator input. Refer to the figures 11.1 and 11.2.
(*) The speed regulator of the PID type is converted into a P type, with proportional gain 1.00 and a null integral
gain.
When Speed is selected, the gains of the speed regulator become again defined by P0161 and P0162. In the
applications with torque control it is recommended to follow the method described at the parameter P0160.
- DC Link Regulation: it must be used when P0184=2. For more details, refer to this parameter description in
the section 11.8.7 of this manual.
- JOG+ and JOG-: those are functions valid only for P0202=3 or 4.
P0264 P0265
(DI2) (DI3)
15 15
16 16
17 17
18 18
19 19
20 20
21 21
22 22
24 24
25 25
26 26
27 27
28 28
29 29
30 30
31 31
40 Digital Input
Digital and Analog Inputs and Outputs
P0266 P0267 P0268
(DI4) (DI5) (DI6)
15 15 15
16 16 16
17 17 17
18 18 18
19 19 19
20 20 20
21 21 21
22 22 22
24 24 24
25 25 25
26 26 26
27 27 27
28 28 28
29 29 29
30 30 30
31 31 31
or 01 PARAMETER GROUPS
40 Digital Input
P0269 P0270
(DI7) (DI8)
15 15
16 16
17 17
18 18
19 19
20 20
21 21
22 22
24 24
25 25
26 26
27 27
28 28
29 29
30 30
31 31
13-13
13