Selection; Electrical Data, 380-500 - Danfoss VLT AutomationDrive FC 300 Design Manual

Selection

4 Selection
4.1 Electrical Data, 380–500 V
FC 302
4 4
High/Normal load*
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
Typical shaft ouptut at 500 V [kW]
Enclosure IP21
Enclosure IP54
Enclosure IP20
Output current
Continuous (at 400 V) [A]
Intermittent (60 s overload)
(at 400 V)[A]
Continuous (at 460/500 V) [A]
Intermittent (60 s overload)
(at 460/500 V) [kVA]
Continuous kVA (at 400 V) [kVA]
Continuous kVA (at 460 V) [kVA]
Continuous kVA (at 500 V) [kVA]
Maximum input current
Continuous (at 400 V) [A]
Continuous (at 460/500 V) [A]
Max. cable size: line power, motor,
brake and load share [mm
Max. external electrical fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
Weight, enclosure IP21, IP54 kg (lbs.)
Weight, enclosure IP20 kg (lbs.)
5)
Efficiency
Output frequency
Heatsink overtemp trip
Control card ambient trip
*High overload=150% current for 60 s, Normal overload=110% current for 60 s
Table 4.1 Technical Specifications, D-frame 380–500 V Line Power Supply 3x380–500 V AC
1) American Wire Gauge.
2) Wiring terminals on N132, N160, and N315 adjustable frequency drives cannot receive cables one size larger.
3) For fuse ratings, see chapter 7.2.1 Fuses.
4) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the adjustable frequency drive.
If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical control card power consumptions are
included. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
5) Measured using 16.5 ft. [5 m] shielded motor cables at rated load and rated frequency.
6) Additional frame size weights are as follows: D5h - 166 (255) / D6h - 129 (285) / D7h - 200 (440) / D8h - 225 (496). Weights are in kg (lbs).
64
Design Guide
N90K
HO NO
90 110
125 150
110 132
D1h
D1h
D3h
177 212
266 233
160 190
240 209
123 147
127 151
139 165
171 204
154 183
2x95 (2x3/0)
2 1)2)
(AWG)]
315
3
4) 5) 2031 2559 2289
4) 5) 1828 2261 2051
6)
6)
167 °F [75 °C]
Danfoss A/S © Rev. 2014-02-10 All rights reserved.
N110 N132
HO NO HO NO
110 132 132 160 160
150 200 200 250 250
132 160 160 200 200
D1h D1h
D1h D1h
D3h D3h
212 260 260 315 315
318 286 390 347 473
190 240 240 302 302
285 264 360 332 453
147 180 180 218 218
151 191 191 241 241
165 208 208 262 262
204 251 251 304 304
183 231 231 291 291
350 400
2954 2923 3770 3093
2724 2089 3628 2872
62 (135)
62 (135)
0.98
0–590 Hz
230 °F [110 °C]
± 15% (tolerance relates to variety in voltage and cable conditions.) These
N160 N200
HO NO HO NO
200 200 250
300 300 350
250 250 315
D2h D2h
D2h D2h
D4h D4h
395 395 480
435 593 528
361 361 443
397 542 487
274 274 333
288 288 353
313 313 384
381 381 463
348 348 427
2x185 (2x350 mcm)
550 630
4116 4039 5137 5005
3569 3575 4566 4458
125 (275)
125 (275)
176 °F [80 °C]
N250
HO NO
250 315
350 450
315 355
D2h
D2h
D4h
480 588
720 647
443 535
665 588
333 407
353 426
384 463
463 567
427 516
800
6674
5714
MG34S222