Danfoss VLT AutomationDrive FC 300 Design Manual page 79

Selection
FC 302
High/ Normal load*
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [HP]
Typical shaft output at 690 V [kW]
Enclosure IP21, IP54 without/with
options cabinet
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V)
[A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload)
(at 575/690 V) [A]
Continuous KVA (at 550 V) [KVA]
Continuous KVA (at 575 V) [KVA]
Continuous KVA (at 690 V) [KVA]
Maximum input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V) [A]
2
Max. cable size, motor [mm (AWG)
Max. cable size, line power F12
[mm 2 (AWG) 1) ]
Max. cable size, line power F13
2 1)
[mm (AWG) ]
2
Max. cable size, brake [mm (AWG
Max. external electrical fuses [A] 2)
Estimated power loss at 600 V [W]
Estimated power loss at 690 V [W]
F3/F4 Max added losses CB or
disconnect & contactor
Max panel options losses
Weight, enclosure IP21, IP 54 [kg]
Weight, rectifier module [kg]
Weight, inverter module [kg]
4)
Efficiency
Output frequency
Power heatsink overtemp. trip
Power card ambient trip
* High overload=160% torque during 60 s, Normal overload=110% torque during 60 s.
Table 4.14 Technical Specifications, F12/F13 frames, 525–690 V Line Power Supply 6x525–690 V AC, 12-Pulse
1) American Wire Gauge.
2) For fuse ratings, see chapter 7.2.1 Fuses.
3) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the adjustable frequency drive.
If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical control card power consumptions are
included. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
4) Measured using 16.5 ft. [5 m] shielded motor cables at rated load and rated frequency.
MG34S222
Design Guide
P900
HO NO
750 850
1050 1150
900 1000
F12/F13
988 1108
1482 1219
945 1060
1418 1166
941 1056
941 1056
1129 1267
962 1079
920 1032
920 1032
1)
]
1)
)]
1600
3) 4) 12062 13731
3) 4) 12524 14250
556 665
136
102
203 °F [95 °C]
Danfoss A/S © Rev. 2014-02-10 All rights reserved.
P1M0
HO NO
850 1000
1150 1350
1000 1200
F12/F13
1108 1317
1662 1449
1060 1260
1590 1386
1056 1255
1056 1255
1267 1506
1079 1282
1032 1227
1032 1227
12x150 (12x300 mcm)
8x240 (8x500 mcm)
8x400 (8x900 mcm)
6x185 (6x350 mcm)
2000
13269 16190
13801 16821
634 863
400
1261/1562
136
102
0.98
0–500 Hz
221 °F [105 °C]
185 °F [85 °C]
± 15% (tolerance relates to variety in voltage and cable conditions.) These
P1M2
HO NO
1000 1100
1350 1550
1200 1400
F12/F13
1317 1479
1976 1627
1260 1415
1890 1557
1255 1409
1255 1409
1506 1691
1282 1440
1227 1378
1227 1378
2500
16089 18536
16719 19247
861 1044
1295/1596
136
136
203 °F [95 °C]
77
4 4