Danfoss VLT AutomationDrive FC 300 Design Manual page 76

Selection
FC 302
High/Normal load*
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [HP]
Typical shaft output at 690 V [kW]
Enclosure IP21, IP54 without/with options
cabinet
4 4
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V) [A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V) [A]
Continuous KVA (at 550 V) [KVA]
Continuous KVA (at 575 V) [KVA]
Continuous KVA (at 690 V) [KVA]
Maximum input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V) [A]
Max. cable size, motor [mm
Max. cable size, line power F2 [mm
Max. cable size, line power F4 [mm
Max. cable size, load sharing [mm
Max. cable size, brake [mm
Max. external electrical fuses [A]
Estimated power loss at 600 V [W]
Estimated power loss at 690 V [W]
F3/F4 Max added losses CB or disconnect &
contactor
Max panel options losses
Weight,
enclosure IP21, IP54 (lb [kg])
Weight, rectifier module [kg]
Weight, inverter module [kg]
Efficiency 4)
Output frequency
Heatsink overtemp. trip
Power card ambient trip
* High overload=160% torque during 60 s, Normal overload=110% torque during 60 s.
Table 4.11 Technical Specifications, F2/F4 frames, 525–690 V Line Power Supply 3x525–690 V AC
1) American Wire Gauge.
2) For fuse ratings, see chapter 7.2.1 Fuses.
3) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the adjustable frequency drive.
If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical control card power consumptions are
included. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
4) Measured using 16.5 ft. [5 m] shielded motor cables at rated load and rated frequency.
74
Design Guide
HO
750
1050
900
988
1482
945
1418
941
941
1129
962
920
920
2 1)
(AWG) ]
2 1)
(AWG) ]
2 1)
(AWG) ]
2 (AWG) 1) ]
2 1)
(AWG) ]
2)
3) 4) 12062
3) 4) 12524
556
203 °F [95 °C]
Danfoss A/S © Rev. 2014-02-10 All rights reserved.
P900 P1M0
NO HO
850 850
1150 1150
1000 1000
F2/F4 F2/F4
1108 1108
1219 1662
1060 1060
1166 1590
1056 1056
1056 1056
1267 1267
1079 1079
1032 1032
1032 1032
12x150 (12x300 mcm)
8x240 (8x500 mcm)
8x456 (8x900 mcm)
4x120 (4x250 mcm)
6x185 (6x350 mcm)
1600 2000
13731 13269
14250 13801
665 634
400
1260/1561
136 136
102 102
0.98
0–500 Hz
221 °F [105 °C]
185 °F [85 °C[
± 15% (tolerance relates to variety in voltage and cable conditions.) These
P1M2
NO HO NO
1000 1000 1100
1350 1350 1550
1200 1200 1400
F2/F4
1317 1317 1479
1449 1976 1627
1260 1260 1415
1386 1890 1557
1255 1255 1409
1255 1255 1409
1506 1506 1691
1282 1282 1440
1227 1227 1378
1227 1227 1378
2500
16190 16089 18536
16821 16719 19247
863 861 1044
1294/1595
136
136
203 °F [95 °C]
MG34S222