Danfoss VLT AutomationDrive FC 300 Design Manual page 70

Selection
FC 302
High/Normal load *
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [HP]
Typical shaft output at 500 V [kW]
Enclosure IP21, IP54 without/with
options cabinet
4 4
Output current
Continuous (at 400 V) [A]
Intermittent (60 s overload)
(at 400 V) [A]
Continuous (at 460/500 V) [A]
Intermittent (60 s overload)
(at 460/500 V) [A]
Continuous KVA (at 400 V) [KVA]
Continuous KVA (at 460 V) [KVA]
Continuous KVA (at 500 V) [KVA]
Maximum input current
Continuous (at 400 V) [A]
Continuous (at 460/500 V) [A]
Max. cable size, motor [mm
Max. cable size, line power
2 1)
[mm (AWG)
Max. cable size, brake [mm
Max. external electrical fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
F9/F11/F13 max. added losses A1 RFI,
CB or disconnect, & contactor
F9/F11/F13
Max. panel options losses
Weight, enclosure IP21, IP54 [kg]
Weight, rectifier module [kg]
Weight, inverter module [kg]
4)
Efficiency
Output frequency
Heatsink overtemp. trip
Power card ambient trip
* High overload=160% torque during 60 s, Normal overload=110% torque during 60 s.
Table 4.5 Technical Specifications, F10-F13 frames, 380–500 V Line Power Supply 6x380–500 V AC, 12-Pulse
1) American Wire Gauge.
2) For fuse ratings, see chapter 7.2.1 Fuses.
3) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the adjustable frequency drive.
If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical control card power consumptions are
included. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
4) Measured using 16.5 ft. [5 m] shielded motor cables at rated load and rated frequency.
68
P450
HO
450
600
530
F10/F11
800
1200
730
1095
554
582
632
779
711
2 1)
(AWG) ]
]
2 (AWG) 1) ]
2)
3) 4) 9492
3) 4)
8730
893
102
102
Danfoss A/S © Rev. 2014-02-10 All rights reserved.
Design Guide
P500 P560
NO HO NO HO
500 500 560 560
650 650 750 750
560 560 630 630
F10/F11 F10/F11
880 880 990 990
968 1320 1089 1485
780 780 890 890
858 1170 979 1335
610 610 686 686
621 621 709 709
675 675 771 771
857 857 964 964
759 759 867 867
8x150 (8x300 mcm)
6x120 (6x250 mcm)
4x185 (4x350 mcm)
900
10647 10631 12338 11263 13201 13172 15436 14967 18084 16392 20358
9414 9398 11006 10063 12353 12332 14041 13819 17137 15577 17752
963 951 1054 978
1017/ 1319
102 102
102 102
± 15% (tolerance relates to variety in voltage and cable conditions.) These
P630 P710
NO HO NO HO
630 630 710 710
900 900 1000 1000
710 710 800 800
F10/F11 F12/F13
1120 1120 1260 1260
1232 1680 1386 1890
1050 1050 1160 1160
1155 1575 1276 1740
776 776 873 873
837 837 924 924
909 909 1005 1005
1090 1090 1227 1227
1022 1022 1129 1129
12x150 (12x300 mcm)
6x185 (6x350 mcm)
1500
1093 1092 1230 2067
400
102 136
136 102
0.98
0–590 Hz
203 °F [95 °C]
185 °F [85 °C]
P800
NO HO NO
800 800 1000
1200 1200 1350
1000 1000 1100
F12/F13
1460 1460 1720
1606 2190 1892
1380 1380 1530
1518 2070 1683
1012 1012 1192
1100 1100 1219
1195 1195 1325
1422 1422 1675
1344 1344 1490
2280 2236 2541
1261/ 1562
136
102
MG34S222