Danfoss VLT AutomationDrive FC 300 Design Manual page 75

Selection
FC 302
High/Normal load*
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [HP]
Typical shaft output at 690 V [kW]
Enclosure IP21, IP54 without/with options
cabinet
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V) [A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V) [A]
Continuous KVA (at 550 V) [KVA]
Continuous KVA (at 575 V) [KVA]
Continuous KVA (at 690 V) [KVA]
Maximum input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V) [A]
2
Max. cable size, motor [mm (AWG)
Max. cable size, line power F1 [mm
Max. cable size, line power F3 [mm
Max. cable size, load sharing [mm
2
Max. cable size, brake [mm (AWG)
2)
Max. external electrical fuses [A]
Estimated power loss at 600 V [W]
Estimated power loss at 690 V [W]
F3/F4 Max added losses CB or disconnect &
contactor
Max panel options losses
Weight, enclosure IP21, IP54 [kg]
Weight, rectifier module [kg]
Weight, inverter module [kg]
Efficiency 4)
Output frequency
Heatsink overtemp. trip
Power card ambient trip
* High overload=160% torque during 60 s, Normal overload=110% torque during 60 s.
Table 4.10 Technical Specifications, F1/F3 frames, 525–690 V Line Power Supply 3x525–690 V AC
1) American Wire Gauge.
2) For fuse ratings, see chapter 7.2.1 Fuses.
3) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the adjustable frequency drive.
If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical control card power consumptions are
included. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
4) Measured using 16.5 ft. [5 m] shielded motor cables at rated load and rated frequency.
MG34S222
Design Guide
P630
HO
500
650
630
F1/ F3
659
989
630
945
628
627
753
642
613
613
1)
]
2 1)
(AWG) ]
2 1)
(AWG) ]
2 (AWG) 1) ]
1)
]
3) 4) 8075
3) 4) 8388
342
102
102
203 °F [95 °C]
Danfoss A/S © Rev. 2014-02-10 All rights reserved.
P710
NO HO NO
560 560 670
750 750 950
710 710 800
F1/ F3
763 763 889
839 1145 978
730 730 850
803 1095 935
727 727 847
727 727 847
872 872 1016
743 743 866
711 711 828
711 711 828
8x150 (8x300 mcm)
8x240 (8x500 mcm)
8x456 (8x900 mcm)
4x120 (4x250 mcm)
4x185 (4x350 mcm)
1600
9500 9165 10872
9863 9537 11304
427 419 532
400
1017/1318
102
102
0.98
0–500 Hz
221 °F [105 °C]
185 °F [85 °C]
± 15% (tolerance relates to variety in voltage and cable conditions.) These
P800
HO NO
670 750
950 1050
800 900
F1/ F3
4
889 988
1334 1087
850 945
1275 1040
847 941
847 941
1016 1129
866 962
828 920
828 920
10860 12316
11291 12798
519 615
102
136
203 °F [95 °C]
73
4