Omron NY532-5400 User Manual page 385

Connection status
General Additional
Status Status
(hex) (hex)
01 011A Error code generated by originator:
Connection could not be established
because the buffer was full due to
high traffic.
01 011B Error code returned from target:
The RPI was set to a value that is
below the specifications.
01 0203 Error code generated by originator:
The connection timed out.
01 0204 Error code generated by originator:
The connection open process timed
out.
01 0205 Error code returned from target:
There was a parameter error in the
frame used to open the connection.
01 0302 Error code generated by originator
or returned from target:
The tag data link's allowable band-
width (pps) was exceeded.
01 0311 Error code returned from target:
There was a parameter error in the
frame used to open the connection.
01 0312 Error code returned from target:
There was a parameter error in the
frame used to open the connection.
01 0315 Error code returned from target:
There was a parameter error in the
frame used to open the connection.
01 0316 Error code returned from target:
There was a parameter error in the
frame used to close the connection.
01 031C Error code generated by originator:
Some other error occurred.
NY-series Industrial Panel PC / Industrial Box PC Built-in EtherNet/IP Port User's Manual (W563)
14 Checking Communications Status of Network and Troubleshooting
Source of error
Handling
Configuration 1 Configuration 2
Unexpected network Unexpected network
traffic may have traffic may have been
been received. Use received. Use the Net-
the Network Configu- work Configurator
rator Device Monitor Device Monitor or the
or the Ethernet Tab Ethernet Tab Page to
Page to check the check the bandwidth
bandwidth usage, usage, and correct the
and correct the load. load. If there are places
If there are places where broadcast
where broadcast storms occur, such as
storms occur, such loop connections in the
as loop connections network connection for-
in the network con- mat, then correct them.
nection format, then
correct them.
This error does not Depends on the tar-
occur. get's specifications.
(Contact the target
device's manufacturer.)
Tag data link communications from the target timed out. Check the power
supply and cable wiring of the devices in the communications path,
including the target and switches. If performance has dropped due to
heavy traffic, change the performance settings. For example, increase
the timeout time or RPI setting.
There was no response from the target. Check the power supply and
cable wiring of the devices in the communications path, including the tar-
get and switches.
This error does not Depends on the tar-
occur. get's specifications.
(Contact the target
device's manufacturer.)
Check the connec- Check the target's con-
tion settings (number nection settings (num-
of connections and ber of connections and
RPI) at the origina- RPI). Check the con-
tor and target. nection settings (num-
ber of connections and
RPI) at the originator
and target.
This error does not Depends on the tar-
occur. get's specifications.
(Contact the target
device's manufacturer.)
This error does not Depends on the tar-
occur. get's specifications.
(Contact the target
device's manufacturer.)
This error does not Depends on the tar-
occur. get's specifications.
(Contact the target
device's manufacturer.)
This error does not Depends on the tar-
occur. get's specifications.
(Contact the target
device's manufacturer.)
This error does not The originator gener-
occur. ates this code when an
unsupported response
code is returned from
the target in reply to an
open request.
Configuration 3
Depends on the tar-
get's specifications.
(Contact the target
device's manufacturer.)
Set the originator's RPI
setting to 1 ms or
greater.
14
Depends on the origi-
nator's specifications.
(Contact the originator
device's manufacturer.)
Check the connection
settings (number of
connections and RPI)
at the originator and
target.
Depends on the origi-
nator's specifications.
(Contact the originator
device's manufacturer.)
Depends on the origi-
nator's specifications.
(Contact the originator
device's manufacturer.)
Depends on the origi-
nator's specifications.
(Contact the originator
device's manufacturer.)
Depends on the origi-
nator's specifications.
(Contact the originator
device's manufacturer.)
Depends on the origi-
nator's specifications.
(Contact the originator
device's manufacturer.)
14-11