Menu 22: Additional Menu 0 Set-Up - Emerson unidrive sp User Manual

Safety Product Mechanical
Information Information Installation
Encoder phase angle (servo mode only)
With drive software version V01.08.00 onwards, the encoder phase angles in Pr 3.25 and Pr 21.20 are copied to the SMARTCARD when using
any of the SMARTCARD transfer methods.
With drive software version V01.05.00 to V01.07.01, the encoder phase angles in Pr 3.25 and Pr 21.20 are only copied to the SMARTCARD
WARNING
when using either Pr 0.30 set to Prog (2) or Pr xx.00 set to 3yyy.
This is useful when the SMARTCARD is used to back-up the parameter set of a drive but caution should be used if the SMARTCARD is used to
transfer parameter sets between drives.
Unless the encoder phase angle of the servo motor connected to the destination drive is known to be the same as the servo motor connected
to the source drive, an autotune should be performed or the encoder phase angle should be entered manually into Pr 3.25 (or Pr 21.20). If the
encoder phase angle is incorrect the drive may lose control of the motor resulting in an O.SPd or Enc10 trip when the drive is enabled.
With drive software version V01.04.00 and earlier, or when using software version V01.05.00 to V01.07.01 and Pr xx.00 set to 4yyy is used,
then the encoder phase angles in Pr 3.25 and Pr 21.20 are not copied to the SMARTCARD. Therefore, Pr 3.25 and Pr 21.20 in the destination
would not be changed during a transfer of this data block from the SMARTCARD.
11.20

Menu 22: Additional Menu 0 set-up

Parameter
22.01 Parameter 0.31 set-up
22.02 Parameter 0.32 set-up
22.03 Parameter 0.33 set-up
22.04 Parameter 0.34 set-up
22.05 Parameter 0.35 set-up
22.06 Parameter 0.36 set-up
22.07 Parameter 0.37 set-up
22.10 Parameter 0.40 set-up
22.11 Parameter 0.41 set-up
22.18 Parameter 0.48 set-up
22.20 Parameter 0.50 set-up
22.21 Parameter 0.51 set-up
22.22 Parameter 0.52 set-up
22.23 Parameter 0.53 set-up
22.24 Parameter 0.54 set-up
22.25 Parameter 0.55 set-up
22.26 Parameter 0.56 set-up
22.27 Parameter 0.57 set-up
22.28 Parameter 0.58 set-up
22.29 Parameter 0.59 set-up
RW Read / Write RO Read only
FI Filtered DE Destination
Unidrive SP User Guide
Issue Number: 13
Electrical Getting Basic
installation Started parameters the motor
Range( )
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Pr 1.00 to Pr 21.51
Uni Unipolar Bi
NC Not copied RA
www.controltechniques.com
Running SMARTCARD
Optimization
operation
OL
Pr 6.09
Bi-polar Bit Bit parameter
Rating dependent PT Protected
Onboard Advanced Technical
Diagnostics
PLC parameters Data
Default( )
VT SV
Pr 11.33 RW Uni
Pr 11.32 RW Uni
Pr 5.16 Pr 0.00 RW Uni
Pr 11.30 RW Uni
Pr 11.24 RW Uni
Pr 11.25 RW Uni
Pr 11.23 RW Uni
Pr 5.12 RW Uni
Pr 5.18 RW Uni
Pr 11.31 RW Uni
Pr 11.29 RW Uni
Pr 10.37 RW Uni
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Pr 0.00 RW Uni
Txt Text string
US User save PS
UL Listing
Information
Type
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
PT US
Power down save
255