R&S EB200 Manual page 213

EB200 Manual
With bits 0 to 2 and 7 to 10 and 12 to 13, the host can be informed via an SRQ about parameter
changes. Cyclical polling of the settings by the host is thus stopped during manual operation or if the
signal parameters are to be indicated. In the CONDition section of the register, the change bits are set
after manual control or signal change and are reset by special query commands. Changes done by
front panel or by another remote client affect the change bits equally.
Table 4-11 Change bit allocation in STATus:EXTension register
Bit No. Set by change of
0 Frequency, demodulation, bandwidth, threshold value,
MGC value, control mode, antenna number,
attenuation, type of detector, squelch enable, squelch
control, sensor function, AFC, TONE mode, tone
reference threshold, AUX bit(s), AUX output mode, IF-
panorama display width, IF-panorama display mode,
measuring time
1 FSCAN:
Start frequency, stop frequency, stepwidth, number of
runs, synchronizing time, listening time, scan mode
2 Signal level, offset
7 Display variants, display mode, display disable,
antenna names, display illumination cut-out time,
display brightness
8 Volume, loudspeaker, balance, external reference, tone
monitoring
9 MSCAN:
Number of runs, synchronizing time, listening time,
scan mode
10 DSCAN:
Center frequency, marker frequency, span frequency,
start frequency, stop frequency, BWZOOM, number of
runs, display mode, speed, reference level
12 Frequency, demodulation, bandwidth, threshold value,
antenna number, attenuation, squelch enable, AFC
13 Query bit (set, reset)
4052.2000.02
Reset by one of the commands
FREQ?, DEM?, BAND?, OUTP:SQU:THR?, GCON?,
GCON:MODE?, ROUTe:CLOSe:STATe?,
INP:ATT:STAT?, DET?, OUTP:SQU?,
OUTP:SQU:CONT?, FUNC?, FREQ:AFC?, MEM:CONT?
RX, OUTP:TONE?, OUTP:TONE:THR?, OUTP:BITAx?,
OUTP:AUX?
OUTP:BYTAx?,
CALC:IFPAN:TYPE?, CALC:IFPAN:AVER:TIME?,
MEAS:TIME?
FREQ:STAR?, FREQ:STOP?, SWE:STEP?,
SWE:COUN?, SWE:DWEL?, SWE:HOLD:TIME?,
SWE:DIR?, SWE:CONT?
SENS:DATA?
DISP:MENU?, DISP:CMAP?, DISP:ENAB?,
ROUT:PATH[:DEF]?, DISP:BRIG?, DISP:BRIG:DWEL?
SYST:AUD:VOL?, SYST:SPE:STAT?, SYST:AUD:BAL?,
ROSC:SOUR?, OUTP:TONE:CONT?
MSC:COUN?, MSC:DWEL?, MSC:HOLD:TIME?,
MSC:DIR?; MSC:CONT?
FREQ:DSC:CENT?, FREQ:DSC:MARK?,
FREQ:DSC:SPAN?, FREQ:DSC:STAR?,
FREQ:DSC:STOP?, FREQ:DSC:RES?; DSC:COUNT?,
CALC:DSC:AVER:TYPE?, FREQ:DSC:SPEED?,
VOLT:AC:RANG?
MEM:CONT? MEM0 ... MEM999
MEM: CONT: MPAR? MEM0 ... MEM999
MEM:CONT? MEM0 ... MEM999
MEM: CONT: MPAR? MEM0 ... MEM999
4.139
Remote control
, FREQ:SPAN?,
E-7