Buell 2009 XB Series Service Manual page 685

2009 Buell XB Models Service Manual
FASTENER
Active cable jam nut
Active intake cable connector
Actuator fasteners
Air cleaner backplate fasteners
Air scoop fastener at oil cooler
Anti-rotation screws (lifter)
Axle, rear (final torque, see ANTI-SEIZE
procedure)
Axle, rear (final torque)
Axle, rear (final torque)
Axle, rear (initial torque)
Axle, rear (initial torque)
Axle, rear (initial torque)
Axle (front)
Axle (rear, final torque)
Axle (rear, initial torque)
Axle pinch fastener, rear
Axle pinch fastener, rear
Axle pinch fastener, rear
Axle pinch fastener, rear
Axle pinch fasteners, front
Axle pinch fasteners, rear
Bank angle sensor
Bank angle sensor
Bank angle sensor
Bank angle sensor fastener
Bank angle sensor fastener, Firebolt
BAS fastener
Battery (+) to starter fastener
Battery ground cable and actuator
ground wire
Battery ground cable and actuator
ground wire
Battery terminal fastener
TORQUE VALUE
48-60 in-lbs 5.4-7 Nm
20-24 in lbs 2.3-2.7 Nm
36-40 in-lbs 4-4.5 Nm
84-120 in-lbs 9.5-13.6 Nm
48-72 in-lbs 5.4-8 Nm
55-65 in-lbs 6-7 Nm
48-52 ft-lbs 65-70.5 Nm
48-52 ft-lbs 65-70.5 Nm
48-52 ft-lbs 65-70.5 Nm
23-27 ft-lbs 31.2-36.6 Nm
23-27 ft-lbs 31.2-36.6 Nm
23-27 ft-lbs 31.2-36.6 Nm
39-41 ft-lbs 53-56 Nm
48-52 ft-lbs 65-70.5 Nm
23-27 ft-lbs 31.2-36.6 Nm
40-45 ft-lbs 54-61 Nm
40-45 ft-lbs 54-61 Nm
40-45 ft-lbs 54-61 Nm
40-45 ft-lbs 54-61 Nm
20-22 ft-lbs 27-30 Nm
40-45 ft-lbs 54-61 Nm
12-36 in-lbs 1.4-4 Nm
12-36 in-lbs 1.4-4 Nm
12-36 in-lbs 1.4-4 Nm
12-36 in-lbs 1.4-4 Nm
12-36 in-lbs 1.4-4 Nm
60-96 in-lbs 7-11 Nm
60-85 in-lbs 7-10 Nm
48-72 in-lbs 5.4-8 Nm
48-72 in-lbs 5.4-8 Nm
72-96 in-lbs 8-11 Nm
NOTES
E.1 ACTIVE INTAKE SYSTEM (JAPANESE
MODELS ONLY), Installation
E.1 ACTIVE INTAKE SYSTEM (JAPANESE
MODELS ONLY), Installation
6.17 INTERACTIVE EXHAUST SYSTEM, Installa-
tion
4.3 AIR CLEANER ASSEMBLY, Installation
3.13 OIL COOLER, Installation/LOCTITE 271 (red)
3.16 HYDRAULIC LIFTERS, Installation
5.7 DRIVE BELT AND IDLER PULLEY, Idler Pulley
Installation/Follow special ANTI-SEIZE procedure.
5.7 DRIVE BELT AND IDLER PULLEY, Drive Belt
Installation/Follow special ANTI-SEIZE procedure.
5.17 TRANSMISSION SPROCKET, Installa-
tion/Follow special ANTI-SEIZE procedure.
5.7 DRIVE BELT AND IDLER PULLEY, Drive Belt
Installation/Follow special ANTI-SEIZE procedure.
5.7 DRIVE BELT AND IDLER PULLEY, Idler Pulley
Installation/Follow special ANTI-SEIZE procedure.
5.17 TRANSMISSION SPROCKET, Installa-
tion/Follow special ANTI-SEIZE procedure.
2.5 FRONT WHEEL, Installation/ANTI-SEIZE, left
handed thread
2.6 REAR WHEEL, Installation/Follow special
instructions, ANTI-SEIZE
2.6 REAR WHEEL, Installation/Follow special
instructions, ANTI-SEIZE
2.37 BELT GUARDS, Installation
5.7 DRIVE BELT AND IDLER PULLEY, Drive Belt
Installation
5.7 DRIVE BELT AND IDLER PULLEY, Idler Pulley
Installation
5.17 TRANSMISSION SPROCKET, Installation
2.5 FRONT WHEEL, Installation
2.6 REAR WHEEL, Installation
4.9 BANK ANGLE SENSOR (BAS), Installation
4.9 BANK ANGLE SENSOR (BAS), Installation
4.9 BANK ANGLE SENSOR (BAS), Installation
2.43 LEFT TAIL SECTION AND BATTERY PAN:
ULYSSES MODELS, Assembly
2.26 HEADLAMP ASSEMBLY AND SUPPORT
BRACKET, Assembly: Firebolt
4.9 BANK ANGLE SENSOR (BAS), Installation
6.7 BATTERY CABLES, Installation
6.7 BATTERY CABLES, Installation
6.29 INTERACTIVE EXHAUST HARNESS: XB12
MODELS, Firebolt
1.5 BATTERY MAINTENANCE, Battery Installation
and Connection
VII