Chrysler 1998 Voyager Service Manual page 40

2 - 8 SUSPENSION
SPECIFICATIONS (Continued)
ALIGNMENT ANGLE
* FRONT INDIVIDUAL CAMBER IN
DEGREES............................................
Front Side To Side Camber
Difference Not To Exceed...................
** FRONT INDIVIDUAL CASTER IN
DEGREES............................................
Front Side To Side Caster Difference
Not To
Exceed.....................................
*** FRONT INDIVIDUAL TOE
RIGHT/
LEFT.........................................
FRONT TOTAL
TOE....................................................
Specified In Degrees
FRONT SIDE TO SIDE TOE
DIFFERENTIAL.....................................
****REAR INDIVIDUAL CAMBER IN
DEGREES............................................
REAR INDIVIDUAL TOE RIGHT/
LEFT........................................
**** REAR TOTAL TOE.....................
Specified In Degrees
TOE OUT: When
Alignment Rack Is TOE In When
Driving
****REAR THRUST ANGLE................
STEERING WHEEL
ANGLE................
FRONT RIDE HEIGHT (MEASURED
AT TOP OF FENDER WHEEL
OPENING)............................................
FRONT RIDE HEIGHT SIDE TO
SIDE
DIFFERENTIAL.....................................
*****REAR RIDE HEIGHT
(MEASURED AT TOP OF FENDER
WHEEL
OPENING)............................................
*****REAR RIDE HEIGHT SIDE TO
SIDE
DIFFERENTIAL.....................................
* Camber is adjustable using the Mopar Camber Adjustment Service Kit. Refer to the Mopar
Parts Catalog for the required service kit part number.
** Caster is not adjustable. If found to be out of specification check for proper ride heights and
damaged/worn out suspension components and replace as necessary.
*** Toe-In is positive.
**** Toe, Camber and thrust angle are not adjustable. If found to be out of specification check for
proper ride heights and damaged/worn out suspension components and replace as necessary.
***** When Measuring ride heights: 1) Ensure that the tire pressures are correct. 2) Jounce the vehicle at the
bumper several times and release at the bottom of the stroke. 3) Measure from the ground to the outboard, lower,
center section of the fender wheel well opening. Ride heights are not adjustable. If found to be out of specification
check for damaged and/or worn out suspension components and replace as necessary.
TIRE SIZES
P205/75/R14
P215/65/R15
+0.15° +or- 0.40°
0.00° - 0.50° MAX
+1.40° + or - 1.00°
0.00° - 1.00° MAX
+0.05°+or- 0.10°
+0.10° +or- 0.20°
0.00° - 0.06° MAX
+0.00° +or- 0.25°
0.00° +or- 0.40°
0.00° +or- 0.40°
Backed On
0.00° +or- 0.30°
0.00° +or- 2.50°
747.5 mm +or-10.0mm
0.0 mm 12.5 mm MAX
766.0 mm +or-10.0mm
0.0 mm 12.5 mm MAX
TIRE SIZES
P205/75/R15
P215/65/R16
+0.05° +or- 0.40°
0.00° - 0.50° MAX
+1.40° + or - 1.00°
0.00° - 1.00° MAX
+0.05° +or- 0.10°
+0.10° +or- 0.20°
0.00° - 0.06° MAX
+0.00° +or- 0.25°
0.00° +or- 0.40°
0.00° +or- 0.40°
0.00° +or- 0.30°
0.00° +or- 2.50°
753.5 mm +or-10.0mm
0.0 mm 12.5 mm MAX
772.0 mm +or-10.0mm
0.0 mm 12.5 mm MAX
NS
ALTERNATIVE FUELS
C.N.G.
ELECTRIC
+0.15° +or- 0.40°
0.00° - 0.50° MAX
+1.40° +or- 1.00°
0.00° - 1.00° MAX
+0.05° +or- 0.10°
+0.10° +or- 0.20°
0.00° - 0.06° MAX
-0.10° +or- 0.25
0.00° +or- 0.40°
0.00° +or- 0.40°
0.00° +or- 0.30°
0.00° +or- 2.50°
783.5 mm +or-10.0mm
0.0 mm 12.5 mm MAX
802.5 mm +or-10.0mm
0.0 mm 12.5 mm MAX