Table of Contents
Advertisement
Network and Security Manager Administration Guide
Viewing Device Monitor Alarm Status
Setting the Polling Interval For Device Alarm Status
638
Table 48: Device Polling Intervals
Statistic
Description
Device
Details traffic, interface, zone, and
system-related statistics on a specific device.
Information appears in the Device Monitor.
VPN
Details VPN tunnels between your managed
devices, including VPN tunnel status (Up, Down,
Not Monitored), VPN name, VPN Type, VPN
source, VPN destination, security parameter
index (SPI), IP address, and protocol.
Information appears in the VPN Monitor.
NSRP
Details high availability events and statistics,
including VSD group ID, number of units in the
cluster, state change counter, init counter,
number of Master devices, number of Backup
devices, and heartbeat information. Information
appears in the NSRP Monitor.
Interface
Details the interface number, IP address, and
zone to which the interface is mapped.
Information appears in the Device Monitor, in
the Device Summary.
Alarms refresh automatically through periodic polling. To view the Alarm status and time:
From Device Monitor, right-click on the device row entry and select the View Alarm
1.
option.
The device Alarm Status dialog box displays the alarm list and polling time for the
device.
To retrieve the current alarm status in the device, click the Refresh button.
2.
The poll time is derived from the device server time.
The default polling interval is 900 seconds (15 minutes). To configure polling intervals
for Alarm Status:
From Device Manager>Devices, double-click on the device to open it.
1.
The Info tab dialog box is displayed.
Select the Device Admin page to set the polling interval for the device.
2.
The minimum polling interval is 60 seconds. The maximum interval is 2,147,483,647
seconds. You cannot disable polling.
Save
Poll Interval
Interval (in
(in seconds)
seconds)
300
300
300
300
300
300
300
300
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1 and is the answer not in the manual?