Table of Contents
Advertisement
Network and Security Manager Administration Guide
136
After the update is complete, the device status displays as "Managed", indicating that
the device has connected and the management system has successfully updated the
device configuration.
Activating a JUNOS Device
The procedure for activating a device with an unknown IP address is similar for all JUNOS
devices. This procedure requires specific actions to be taken on the device in addition to
those taken in the NSM UI. In NSM, you must complete the Activate Device workflow.
You must also make sure the device is properly installed and configured with login
credentials for the NSM administrator, and configure the device to connect with NSM.
Finally, you must load the modeled configuration onto the device:
Install the device and configure it with logon credentials for the NSM administrator:
1.
Connect the device to the network and configure one of the interfaces so that
a.
the device can reach the NSM device server.
Add a user for NSM that has full administrative rights.
b.
Activate the device in NSM:
2.
In Device Manager, right-click the device and then select Activate Device from
a.
the list.
In the Activate Device dialog box, select Device is deployed, but not reachable,
b.
and then click Next.
In the Specify Name and Device type dialog box, perform the following tasks:
c.
Make a note of the automatically generated Unique External ID for the
i.
device. This ID number represents the device within the management system.
The device administrator will need this ID to configure connectivity between
the device and NSM.
Specify the administrator user name and password for the SSH connection.
ii.
This name and password must match the name and password already
configured on the device.
Specify the First Connection One Time Password (OTP) that authenticates
iii.
the device. Make a note of this password. The device administrator will need
it to configure the connectivity between the device and NSM.
NOTE: All passwords handled by NSM are case-sensitive.
Click Finish to complete the Add Device wizard and include the new device in
d.
the Device Manager list.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008