Table of Contents
Advertisement
Copyright © 2010, Juniper Networks, Inc.
In the main navigation tree, click VPN Manager > VPNs.
Click the Add icon and then select AutoKey IKE VPN. The New AutoKey IKE VPN
dialog box appears.
Select the Enable check box to enable the VPN.
Select the default termination zone for the VPN tunnels from the Terminal Point
drop-down list.
Select the type of VPN from the Type drop-down list, and then click OK.
Add the devices to the hub-and-spoke topology.
2.
In the navigation tree, click Security Devices. The Security Devices dialog box
appears.
Click the Add icon, and then select the devices to be included in the hub- and-spoke
topology.
Click OK.
Configure the topology.
3.
In the general configuration area of the VPN Manager, click the Topology link. The
New Topology dialog box appears.
Select the device to be the hub for the topology from the Hub drop-down list.
Select the Enable Auto-Connect VPN check box.
In the Mains pane, select each device you want to be a main. Main devices can
communicate with every other device in the topology.
Click OK, and then click the Save button to save the VPN configuration.
Configure the IP address for the tunnel interface on the hub and spokes.
4.
In the configuration area of this VPN, click the Device Tunnel Summary link. A list
of tunnels appears.
Right-click the tunnels and assign the IP address. The Tunnel Interface dialog box
appears.
Enter the IP address and netmask, and then click OK.
Click the Close button in the AutoKey IKE VPN.
Specify the AutoConnect VPN parameters to complete the procedure.
5.
In the configuration area of this VPN, click the AutoConnect VPN Parameters link.
The AutoConnect VPN Parameters dialog box appears.
Click the Import Gateway and AutoKey Parameters button to import the existing
hub-and-spoke configuration for the hub and spoke. You can configure the VPN
and gateway by using ACVPN-Dynamic(Mains) or ACVPN-Profile(Hub) parameters
in the navigation tree.
Chapter 11: Configuring VPNs
601
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008