Table of Contents
Advertisement
Network and Security Manager Administration Guide
114
Enter the following connection information:
6.
Enter the IP Address of the security device.
Enter the username of the device administrator.
Enter the password for the device administrator.
NOTE: All passwords handled by NSM are case-sensitive.
Select the connection method (Telnet, SSH version 1, SSH version 2) and the port
number for the selected service.
If you selected Telnet, click Next and go directly to step 7.
If you selected an SSH version, click Next and the Verify Device Authenticity dialog
box opens. The device wizard displays the RSA Key FingerPrint information; to
prevent man-in-the-middle attacks, you should verify the fingerprint using an
out-of-band method.
After the wizard displays the autodetected device information, verify that the device
7.
type, ScreenOS version, and the device serial number are correct. NSM autodetects
the hostname configured on the device and uses it as the device name. You can also
change the autodetected hostname.
Modify the autodetected device name within the device from its config editor page
8.
in NSM, and select
Update device
If you modified the device host name through the JUNOS CLI, SNMP, or J-Web
interface, you can modify the device name again in NSM after importing the device,
using the edit option. If the device was bulk added, the name you specify in the CSV
file is used.
NOTE: If you select the
Device is not reachable
detect the hostname automatically. You need to specify a device name.
Click Next to add the device to NSM.
9.
After the device is added, click Next to import the device configuration.
10.
Click Finish to complete the Add Device wizard.
11.
Double-click the device in Device Manager to view the imported configuration.
12.
NOTE: After importing a NetScreen-5GT device that uses extended port mode, NSM
displays the modes as "ns5GT-Trust-Untrust-DMZ" and sets the license mode to
Extended.
To check the device configuration status, mouse over the device in Device Manager (you
can also check configuration status in Device Monitor). The device status displays as
.
or the
Model Device
Copyright © 2010, Juniper Networks, Inc.
workflow, NSM cannot
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008