WAGO 750 Product Manual page 86

750-1632/000-100
Proportional Valve Module, 2 -Channel; 24 VDC; 1.6 A
The 750-1632/000-100 Proportional Valve Module controls two single-coil valves with up to 24 V/1.6 A or one valve with up to 24 V/2 A. The module features two current-con-
trolled PWM* outputs with adjustable dithering.
Both unipolar and bipolar valve control are possible. Additionally, operation of a valve with two unipolar coils is also provided. A two-channel module may also be used for simple
applications. Characteristic curve adaptations, such as zero offset, dual gain compensation or range limitations, can be adjusted via parameters.
Scaling and configurable up/down ramps permit set point adjustment to the application. For example, monitoring threshold value switches is performed via two additional digital in-
puts. Start-up and valve parameters adjustment are performed via WAGO-I/O-CHECK software or the controller.
*PWM = Pulse width modulation
Technical data
Number of digital inputs
Number of outputs
Type of output
Input characteristic
Input characteristic
Input current (typ.)
Output current
Load type
PWM frequency (typ.)
Data width
Supply voltage (system)
Current consumption (5 V system supply)
Supply voltage (field)
Current consumption, field supply (module with no external load)
Isolation
Number of incoming power jumper contacts
Number of outgoing power jumper contacts
Connection data
Connection technology: inputs/outputs
Connection type 1
Connectable conductor materials
Solid conductor
Fine-stranded conductor
Strip length
Connection requirement (permissible cable length)
Connection requirement (permissible cable type)
Note (conductor cross-section)
Temperature range of connection cable
Physical data
Width
Height
Depth
Depth from upper-edge of DIN-rail
Mechanical Data
Mounting type
Material Data
Color
Housing material
Fire load
Weight
Conformity marking
Environmental requirements
Ambient temperature (operation)
Surrounding air temperature (storage)
Protection type
Pollution degree
Operating altitude
Mounting position
Relative humidity (without condensation)
Vibration resistance
Shock resistance
WAGO GmbH & Co. KG
Subject to changes
2
2 bipolar outputs (A+, A- and B+, B-)
H-bridge output with current-regulated PWM output (short-circuit-proof and thermal over-
load-proof for each channel)
high-side switching
Type 1
2.7 mA at 24 V
1-channel operation: 2 A; 2-channel operation: 1.6 A per channel
Operating range: inductive (1 mH ... 600 mH); Internal load resistance (> 8 Ohm)
25 kHz
6 bytes: single-channel operating mode; 12 bytes: dual-channel operating mode
5 VDC; via data contacts
125 mA
24 VDC (-25 ... +30 %); via power jumper contacts (power supply via blade contact; trans-
mission via spring contact)
20 mA
500 V system/field
2
2
16 x Push-in CAGE CLAMP®
Inputs/outputs
copper
0.08 ... 1.5 mm² / 28 ... 16 AWG
0.25 ... 1.5 mm² / 22 ... 16 AWG
8 ... 9 mm / 0.31 ... 0.35 inches
30 m
Outputs
Coil connections A+/A-/B+/B-: 1.5 mm²/16 AWG; For use according to UL: 16 AWG for all
connections
The permissible temperature range of the connecting cable must be dimensioned based on
the mounting position and current intensity, as the temperature of the terminal connection
can be up to 25 K above the maximum expected surrounding air temperature (at 10 A).
12 mm / 0.472 inch
100 mm / 3.937 inch
69 mm / 2.717 inch
61.8 mm / 2.433 inch
DIN-35 rail
light gray
Polycarbonate; polyamide 6.6
0,824 MJ
54,4 g
CE
0 ... +55 °C
-25 ... +85 °C
IP20
2 per IEC 61131-2
0 ... 2000 m / 0 ... 6562 ft
horizontal (standing/lying); vertical
95 %
4g per IEC 60068-2-6
15g per IEC 60068-2-27
Postfach 2880 - D-32385 Minden
18.09.23
Hansastr. 27 - D-32423 Minden
Phone: +49(0)571/887-0 Email: info@wago.com
Fax: +49(0)571/887-844169 www.wago.com