Table of Contents
Advertisement
VLT® AutomationDrive FC 302
Operating Guide
FC 302
Intermittent (60 s overload) (at 575/690 V) [A]
Continuous kVA (at 550 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Maximum input current
Continuous (at 525 V) [A]
Continuous (at 575/690 V) [A]
Maximum number and size of cables per phase
2
- Mains [mm
(AWG)]
- Mains with disconnect [mm
- Mains with fusible disconnect [mm
- Mains with contactor [mm
2
- Motor [mm
(AWG)]
Drive module power loss at 600 V [W]
Drive module power loss at 690 V [W]
Drive efficiency
(2)
Output frequency [Hz]
(4)
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
PHF overtemperature trip [°C (°F)]
Line reactor overtemperature trip [°C (°F)]
dU/dt filter overtemperature trip [°C (°F)]
Sine-wave filter overtemperature trip [°C (°F)]
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These
1
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimension-
ing of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control card power
consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-efficiency-direc-
tive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each
add only 4 W.
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficien-
2
cy class, see the Ambient Conditions section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
See also Input Power Option Losses section.
3
If using an output filter, the output frequency is limited further. See
4
Table 107: Electrical Data, Mains Supply 3x525–690 V AC
FC 302
High/normal overload
168 | Danfoss A/S © 2021.10
2
(AWG)]
2
(AWG)]
2
(AWG)]
(1)(2)(3)
(1)(2)(3)
N200
363
319
230
276
241
289
289
347
244
292
233
279
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
3012
3723
3123
3851
0.98
0–590
110 (230)
80 (176)
150 (302)
150 (302)
150 (302)
150 (302)
10.3.1 Motor Output (U, V,
W).
N355
HO
NO
Specifications
N250
N315
435
378
516
276
327
327
289
343
343
347
411
411
292
347
347
279
332
332
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
3642
4465
4146
3771
4614
4258
0.98
0.98
0–590
0–590
110 (230)
110 (230)
80 (176)
80 (176)
150 (302)
150 (302)
150 (302)
150 (302)
150 (302)
150 (302)
150 (302)
150 (302)
N400
N500
HO
NO
HO
AQ262139143212en-000301 / 130R0879
440
380
398
478
403
385
5028
5155
NO
Advertisement
Table of Contents
Troubleshooting
